Filter by
System of Measurement
Thread Size
Movement
Overall Height
Body Style
Capacity per Mount
Shank Thread Size
Height
Base Diameter
Installation Torque
Mount Movement
Rod End Type
Export Control Classification Number (ECCN)
Hoist Rings—For Lifting
 |
 |
180° Pivot |
 |
360° Swivel |
Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back and a base that swivels 360° to compensate for pitch, roll, and sway when lifting heavy or unbalanced loads. Install the base of the hoist ring flush to the mounting surface and tighten to the recommended torque that is stamped on the ring. Torque wrenches are sold separately.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
High Visibility—High-visibility hoist rings are fluorescent green, so they’re easy to distinguish from other hardware when attached to equipment being lifted.
Machined—Machined hoist rings have a smooth finish to protect slings and hooks from damage and excess wear during lifting.
Black-Oxide Steel—Black-oxide steel hoist rings have mild corrosion resistance.
Nickel-Plated Steel—Nickel-plated steel hoist rings are more corrosion resistant than black-oxide steel hoist rings.
316 Stainless Steel—316 stainless steel hoist rings are the most corrosion resistant.
CE Marked—Hoist rings that are CE marked meet European safety standards.
Each | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Lg. | Inside Wd. | Overall Ht. | Vert. Cap., lb. | Movement | Specs. Met | Certification | Mil. Spec. | 1-9 | 10-Up | |||
Forged Black-Oxide Steel | |||||||||||||
| 7/8"-9 | 1" | 3" | 8 3/8" | 8,000 | 180° Pivot and 360° Swivel | ASME B30.26 | CE Marked, Mil. Spec. | MIL-STD-1365, MIL-STD-209 | 2994T475 | 0000000 | 0000000 | ||
| 7/8"-9 | 1" | 3" | 10" | 8,000 | 180° Pivot and 360° Swivel | ASME B30.26 | CE Marked, Mil. Spec. | MIL-STD-1365, MIL-STD-209 | 2994T485 | 000000 | 000000 | ||
| 7/8"-9 | 1 1/4" | 3" | 8 5/8" | 8,000 | 180° Pivot and 360° Swivel | ASME B30.26 | CE Marked, Mil. Spec. | MIL-STD-1365, MIL-STD-209 | 2994T74 | 000000 | 000000 | ||
| 7/8"-9 | 1 1/4" | 3" | 10 1/4" | 8,000 | 180° Pivot and 360° Swivel | ASME B30.26 | CE Marked, Mil. Spec. | MIL-STD-1365, MIL-STD-209 | 2994T98 | 000000 | 000000 | ||
Machined Black-Oxide Steel | |||||||||||||
| 7/8"-9 | 1 1/16" | 2 3/4" | 7 5/8" | 8,000 | 180° Pivot and 360° Swivel | ASME B30.26 | CE Marked, Mil. Spec. | MIL-STD-1365, MIL-STD-209 | 3052T65 | 000000 | 000000 | ||
Forged Fluorescent Green Powder-Coated Steel—High Visibility | |||||||||||||
| 7/8"-9 | 15/16" | 3" | 8 5/16" | 8,000 | 180° Pivot and 360° Swivel | ASME B30.26 | CE Marked, Mil. Spec. | MIL-STD-1365, MIL-STD-209 | 4157N18 | 000000 | 000000 | ||
Machined Nickel-Plated Steel | |||||||||||||
| 7/8"-9 | 1" | 2 3/4" | 7 5/8" | 8,000 | 180° Pivot and 360° Swivel | ASME B30.26 | CE Marked, Mil. Spec. | MIL-STD-1365, MIL-STD-209 | 3145T74 | 000000 | 000000 | ||
Machined 316 Stainless Steel | |||||||||||||
| 7/8"-9 | 1 1/16" | 2 7/8" | 7 5/8" | 4,000 | 180° Pivot and 360° Swivel | ASME B30.26 | CE Marked, Mil. Spec. | MIL-STD-1365, MIL-STD-209 | 2949T29 | 000000 | 000000 | ||
Swivel-Under-Load Hoist Rings—For Lifting
 |
|
180° Pivot |
|
360° Swivel |
The ball bearing on these hoist rings makes it easy to rotate your load even after it’s suspended. For unbalanced or heavy loads, the base also swivels to compensate for pitch, roll, and sway. Their lifting ring pivots 180° front to back. Ideal for angular lifting, these hoist rings withstand stresses that bend or break eyebolts.
Install the base of these hoist rings flush to your mounting surface. Use a torque wrench to tighten to the recommended torque stamped on the ring.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
Thread Size | Thread Lg. | Inside Wd. | Overall Ht. | Vert. Cap., lb. | Movement | Specs. Met | Certification | Each | |||
|---|---|---|---|---|---|---|---|---|---|---|---|
Forged Yellow Powder-Coated Steel | |||||||||||
| 7/8"-9 | 1 3/16" | 1 5/16" | 6 13/16" | 10,580 | 180° Pivot and 360° Swivel | ASME B30.26 | CE Marked | 4137N27 | 0000000 | ||
Removable-Shackle Hoist Rings—For Lifting
 |
|
180° Pivot |
|
360° Swivel |
Remove the shackle after lifting while keeping the base installed for future use. Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back and a base that swivels 360° to compensate for pitch, roll, and sway when lifting heavy or unbalanced loads. Install the base of the hoist ring flush to the mounting surface and tighten to the recommended torque that is stamped on the ring. Torque Wrenches are sold separately.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
Thread Size | Thread Lg. | Inside Wd. | Overall Ht. | Vert. Cap., lb. | Movement | Specs. Met | Certification | Each | |||
|---|---|---|---|---|---|---|---|---|---|---|---|
Machined Black-Oxide Steel Base with Zinc-Plated Steel Eye | |||||||||||
| 7/8"-9 | 1 1/4" | 2 5/8" | 8 1/2" | 8,000 | 180° Pivot and 360° Swivel | ASME B30.26 | CE Marked | 3026T24 | 0000000 | ||
Hoist Ring Assortments—For Lifting
 |  |
Hoist Ring Assembly (Retaining Ring Not Pictured) |
| |
180° Pivot | 360° Swivel |
Keep on hand all the parts needed to assemble custom hoist rings. Ideal for angular lifting, these hoist rings will withstand stresses that bend or break eyebolts. The base of these hoist rings will swivel 360° to compensate for pitch, roll, and sway when lifting heavy or unbalanced loads. The shackle will pivot 180° front to back. All parts have a black oxide finish for mild corrosion resistance.
Install the base of these hoist rings flush to your mounting surface. Use a torque wrench to tighten to the recommended torque stamped on the ring.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
No. of Pieces | Thread Size | Movement | Includes | Specs. Met | Each | |||
|---|---|---|---|---|---|---|---|---|
Forged Black-Oxide Steel | ||||||||
| 104 | 1/2"-13 5/8"-11 3/4"-10 7/8"-9 1"-8 | 180° Pivot and 360° Swivel | Four 3/4" Dia. Shackles Four 1" Dia. Shackles Four 1/2"-13 Bolts for 3/4" Dia. Shackle—2,500 lbs. Capacity and 1" Thread Lg. Four 5/8"-11 Bolts for 3/4" Dia. Shackle—4,000 lbs. Capacity and 1" Thread Lg. Four 3/4"-10 Bolts for 3/4" Dia. Shackle—5,000 lbs. Capacity and 1" Thread Lg. Four 3/4"-10 Bolts for 1" Dia. Shackle—7,000 lbs. Capacity and 1 1/2" Thread Lg. Four 7/8"-9 Bolts for 1" Dia. Shackle—8,000 lbs. Capacity and 1 1/2" Thread Lg. Four 1"-8 Bolts for 1" Dia. Shackle—10,000 lbs. Capacity and 1 1/2" Thread Lg. 24 Bushings 24 Retaining Rings 24 Washers | ASME B30.26 | 5602N12 | 000000000 | ||
Swivel Leveling Mounts with Threaded Stud
 |
Without Cushion |
 |
With Cushion |
Keep equipment level on slightly sloped and pitted floors with mounts that have a ball-and-socket joint in the base. For mounting versatility, you can install them in either threaded holes or unthreaded through holes at the bottom of equipment.
Nickel-Plated Steel Base—With a shiny appearance, these mounts create a finished look. They're best for dry environments since the nickel plating offers minimal corrosion resistance.
Zinc-Yellow-Chromate-Plated Steel Base—More corrosion resistant than nickel-plated steel, these mounts are suitable for damp environments. However, they won’t hold up to chemical cleaners, high-pressure washdowns, and other harsh conditions like stainless steel can.
Black-Oxide Steel Base—With a matte black appearance, these mounts create a finished look. They offer minimal corrosion resistance, so they're best for dry environments.
303 Stainless Steel Base—The choice for most wet locations, these mounts can withstand repeated washdowns without corroding. However, they won't hold up to cleaning solutions that contain harsh chemicals like 316 stainless steel can.
Delrin® Acetal Base—These mounts are economical yet resistant to grease, oil, and chemicals that pool on the floor. Often used on small, lightweight machines, they have about 25% the capacity of similarly sized metal mounts.
Rubber Cushion—A cushion under the base grips surfaces so vibrating equipment doesn't slide. It also protects floors from scrapes and gouges.
Without Cushion | With Rubber Cushion | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Lg. | Swivel Range of Motion | Base Dia. | Cap. per Mount, lb. | Overall Ht. | Each | Cap. per Mount, lb. | Overall Ht. | Cushion Material | Each | ||||
Nickel-Plated Steel Base and Stud | ||||||||||||||
| 7/8"-9 | 4" | 7.5° | 4" | 15,000 | 5 7/8" | 6111K158 | 000000 | 11,250 | 6" | Natural Rubber | 6111K249 | 000000 | ||
Zinc-Yellow-Chromate-Plated Steel Base and Stud | ||||||||||||||
| 7/8"-9 | 4" | 7.5° | 4" | 15,000 | 5 7/8" | 6111K174 | 00000 | 11,250 | 6" | Natural Rubber | 6111K208 | 00000 | ||
Black-Oxide Steel Base and Zinc-Plated Steel Stud | ||||||||||||||
| 7/8"-9 | 4" | 7.5° | 4" | 15,000 | 5 7/8" | 6111K242 | 00000 | 11,250 | 6" | Natural Rubber | 6111K533 | 00000 | ||
303 Stainless Steel Base and Stud | ||||||||||||||
| 7/8"-9 | 4" | 7.5° | 4" | 15,000 | 5 7/8" | 6111K195 | 00000 | 11,250 | 6" | Natural Rubber | 5546N32 | 000000 | ||
Delrin® Acetal Base and Zinc-Plated Steel Stud | ||||||||||||||
| 7/8"-9 | 4" | 7.5° | 4" | — | — | ——— | 0 | 1,700 | 6" | Natural Rubber | 6111K494 | 00000 | ||
Fully Threaded Rod End Bolts
 |  |
For maximum mounting flexibility, cut the fully threaded shaft to whatever length you need. Also known as swing bolts and eyebolts, rod end bolts have no moving parts. They're designed to make pivoting or hinge movements in applications that don't need to compensate for misalignment.
Shank | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Ctr. Lg. | Thread Lg. | ID | Overall Wd. | Shank Threading | Overall Thk. | Tensile Strength | Specs. Met | Each | |||
Right-Hand Shank Thread | ||||||||||||
Black-Oxide Carbon Steel | ||||||||||||
| 7/8"-9 | 5" | 3 13/16" | 7/8" | 1 7/8" | Fully Threaded | 7/8" | Not Rated | ASTM A521 Grade CA | 3798K45 | 000000 | ||
| 7/8"-9 | 6" | 4 13/16" | 7/8" | 1 7/8" | Fully Threaded | 7/8" | Not Rated | ASTM A521 Grade CA | 3798K33 | 00000 | ||
Side-Mount Hoist Rings—For Lifting
 |  |
D-Shape | D-Shape (Side View) |
 |  |
Triangle | Triangle (Side View) |
| |
180° Pivot | 360° Swivel |
Choose these hoist rings when you need to lift your load from the side. Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back and a base that swivels 360° to compensate for pitch, roll, and sway when lifting heavy or unbalanced loads. Install the base of the hoist ring flush to the mounting surface and tighten to the recommended torque that is stamped on the ring. Torque wrenches are sold separately.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
D-Shape—D-shape hoist rings have a wider end than triangle hoists, so it’s easier to attach webbing and large hooks.
Triangle—Triangle hoist rings have a narrow end to keep chain in place.
Black-Oxide Steel—Black-oxide steel hoist rings have mild corrosion resistance.
Thread Size | Thread Lg. | Inside Wd. | Overall Ht. | Vert. Cap., lb. | Movement | Specs. Met | Each | |||
|---|---|---|---|---|---|---|---|---|---|---|
D-Shape | ||||||||||
Forged Black-Oxide Steel | ||||||||||
| 7/8"-9 | 1 5/16" | 3 1/2" | 8 3/16" | 8,000 | 180° Pivot and 360° Swivel | ASME B30.26 | 7995N37 | 0000000 | ||
Triangle | ||||||||||
Forged Black-Oxide Steel | ||||||||||
| 7/8"-9 | 1 1/4" | 1 3/4" | 7 13/16" | 8,000 | 180° Pivot and 360° Swivel | ASME B30.26 | 7995N17 | 000000 | ||
Rotating Eyebolts—For Lifting
Powder-Coated Steel
 |  |
Thread | With Shoulder | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
Size | Lg. | Shank Lg. | Eye Dia. | Vert. Cap., lb. | Threading | Color | Overall Lg. | Each | |||
Closed Eye | |||||||||||
| 7/8"-9 | 1 5/32" | 1 5/32" | 1 9/16" | 5,050 | Fully Threaded | Pink | 4 1/8" | 3059T113 | 0000000 | ||
Rotating Flange Nuts
 |
Steel
Flange | |||||||||
|---|---|---|---|---|---|---|---|---|---|
Thread Size | Wd. | Ht. | Dia. | Thk. | Material | Each | |||
Black-Oxide Steel | |||||||||
| 7/8"-9 | 1 7/16" | 1 1/8" | 1 3/4" | 0.44" | Steel | 90477A037 | 000000 | ||
Swivel Leveling Mounts with Threaded Hole
 |
Without Cushion |
Without Cushion | |||||||||
|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Dp. | Swivel Range of Motion | Base Dia. | Cap. per Mount, lb. | Overall Ht. | Each | |||
303 Stainless Steel Base | |||||||||
| 7/8"-9 | 13/16" | 7.5° | 4" | 15,000 | 1 7/8" | 6103K226 | 000000 | ||
Corrosion-Resistant Fully Threaded Rod End Bolts
 |
304 Stainless Steel |
|
These rod end bolts are good for wet and corrosive environments—for maximum mounting flexibility, cut the fully threaded shaft to whatever length you need. Also known as swing bolts and eyebolts, rod end bolts have no moving parts. They're designed to make pivoting or hinge movements in applications that don't need to compensate for misalignment.
304 Stainless Steel—303 and 304 stainless steel rod end bolts won't rust in humid, wet, and washdown environments. They're stronger than brass bolts and nearly as strong as steel. They will rust when exposed to salt water and chemicals, however.
ASTM A193—ASTM rod end bolts meet a standard for material.
Shank | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Ctr. Lg. | Thread Lg. | ID | Overall Wd. | Shank Threading | Overall Thk. | Tensile Strength, psi | Specs. Met | Fastener Strength Grade/Class | Each | |||
Right-Hand Shank Thread | |||||||||||||
304 Stainless Steel | |||||||||||||
| 7/8"-9 | 5" | 3 13/16" | 7/8" | 1 7/8" | Fully Threaded | 7/8" | 75,000 | ASTM A193 | ASTM Grade B8 | 2434K44 | 000000 | ||
| 7/8"-9 | 6" | 4 13/16" | 7/8" | 1 7/8" | Fully Threaded | 7/8" | 75,000 | ASTM A193 | ASTM Grade B8 | 2434K33 | 00000 | ||
High-Strength Fully Threaded Rod End Bolts
 | |
These alloy steel rod end bolts have the highest tensile strength of any steel fully threaded rod end bolt we offer. For maximum mounting flexibility, cut the fully threaded shaft to whatever length you need. Also known as swing bolts and eyebolts, rod end bolts have no moving parts. They're designed to make pivoting or hinge movements in applications that don't need to compensate for misalignment.
Shank | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Ctr. Lg. | Thread Lg. | ID | Overall Wd. | Shank Threading | Overall Thk. | Tensile Strength, psi | Specs. Met | Fastener Strength Grade/Class | Each | |||
Right-Hand Shank Thread | |||||||||||||
Black-Oxide Alloy Steel | |||||||||||||
| 7/8"-9 | 5" | 3 13/16" | 7/8" | 1 7/8" | Fully Threaded | 7/8" | 125,000 | ASTM A193 | ASTM Grade B7 | 2440K45 | 000000 | ||
| 7/8"-9 | 6" | 4 13/16" | 7/8" | 1 7/8" | Fully Threaded | 7/8" | 125,000 | ASTM A193 | ASTM Grade B7 | 2440K33 | 00000 | ||
Partially Threaded Rod End Bolts
 |  |
Shank | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Ctr. Lg. | Thread Lg. | ID | Overall Wd. | Shank Threading | Overall Thk. | Tensile Strength, psi | Each | |||
Right-Hand Shank Thread | |||||||||||
Black-Oxide Carbon Steel | |||||||||||
| 7/8"-9 | 6" | 2" | 3/4" | 1 3/4" | Partially Threaded | 15/16" | 75,000 | 6066K61 | 000000 | ||
| 7/8"-9 | 12" | 4" | 3/4" | 1 3/4" | Partially Threaded | 15/16" | 75,000 | 6066K62 | 00000 | ||
| 7/8"-9 | 6" | 2" | 7/8" | 1 3/4" | Partially Threaded | 15/16" | 75,000 | 6066K72 | 00000 | ||
Tension-Indicating Hoist Rings—For Lifting
 |  |
|
180° Pivot |
|
360° Swivel |
An indicator dot changes from red to black when these hoist rings are properly tightened, eliminating the need for a torque wrench. The dot changes back to red if the hoist ring comes loose. Ideal for angular lifting, these hoist rings withstand stresses that bend or break eyebolts. They have a lifting ring that pivots 180° front to back and a base that swivels 360° to compensate for pitch, roll, and sway when lifting heavy or unbalanced loads. A black oxide finish gives these hoist rings mild corrosion resistance.
Install the base of these hoist rings flush to your mounting surface.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
Rings | Replacement Bolt Kits for Hoist Rings | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Lg. | Inside Wd. | Overall Ht. | Vert. Cap., lb. | Tension Indicated, ft·lbf | Indicator Temp., ° F | Movement | Specs. Met | Certification | Each | Each | ||||
Forged Black-Oxide Steel with Zinc-Plated Steel Bolt | |||||||||||||||
| 7/8"-9 | 1" | 2 13/16" | 7 1/2" | 8,000 | 160 | 0 to 165 | 180° Pivot and 360° Swivel | ASME B30.26 | CE Marked | 5596N21 | 0000000 | 5596N41 | 0000000 | ||
| 7/8"-9 | 1 1/4" | 2 13/16" | 7 3/4" | 8,000 | 160 | 0 to 165 | 180° Pivot and 360° Swivel | ASME B30.26 | CE Marked | 5596N22 | 000000 | 5596N42 | 000000 | ||
