How to Identify and Measure Fittings
Pipe size is an industry designation, not the actual size. View information about how to measure threaded and unthreaded pipe and pipe fittings.
More
About Leveling Mounts
More
About Lifting with Hoist Rings
More
Hoist Rings—For Lifting
Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back and a base that swivels 360° to compensate for pitch, roll, and sway when lifting heavy or unbalanced loads. Install the base of the hoist ring flush to the mounting surface and tighten to the recommended torque that is stamped on the ring. Torque wrenches are sold separately.
Machined hoist rings have a smooth finish to protect slings and hooks from damage and excess wear during lifting.
Black-oxide steel hoist rings have mild corrosion resistance.
Nickel-plated steel hoist rings are more corrosion resistant than black-oxide steel hoist rings.
High-visibility hoist rings are fluorescent green, so they’re easy to distinguish from other hardware when attached to equipment being lifted.
Hoist rings that are CE marked meet European safety standards.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Lg., mm | Inside Wd., mm | Overall Ht., mm | Vertical Capacity, lbs. | Movement | Specifications Met | Each | |
Forged Black-Oxide Steel | |||||||||
---|---|---|---|---|---|---|---|---|---|
M30 | 3.5 | 38 | 71 | 226 | 9,900 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 00000000 | 0000000 |
M30 | 3.5 | 38 | 71 | 267 | 9,900 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 00000000 | 000000 |
M30 | 3.5 | 48 | 71 | 236 | 9,900 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 0000000 | 000000 |
M30 | 3.5 | 48 | 71 | 277 | 9,900 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 00000000 | 000000 |
M30 | 3.5 | 67 | 101 | 302 | 15,425 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 0000000 | 000000 |
Machined Black-Oxide Steel | |||||||||
M30 | 3.5 | 46 | 89 | 268 | 15,425 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 00000000 | 000000 |
M30 | 3.5 | 54 | 71 | 220 | 9,900 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 00000000 | 000000 |
M30 | 3.5 | 54 | 71 | 261 | 9,900 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 00000000 | 000000 |
M30 | 3.5 | 66 | 89 | 288 | 15,425 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 00000000 | 000000 |
Forged Fluorescent Green Powder-Coated Steel—High Visibility | |||||||||
M30 | 3.5 | 38 | 76.2 | 225.2 | 4,500 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 0000000 | 000000 |
Forged Nickel-Plated Steel | |||||||||
M30 | 3.5 | 38 | 71 | 226 | 9,900 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 0000000 | 000000 |
Swivel-Under-Load Hoist Rings—For Lifting
The ball bearing on these hoist rings makes it easy to rotate your load even after it’s suspended. For unbalanced or heavy loads, the base also swivels to compensate for pitch, roll, and sway. Their lifting ring pivots 180° front to back. Ideal for angular lifting, these hoist rings withstand stresses that bend or break eyebolts.
Install the base of these hoist rings flush to your mounting surface. Use a torque wrench to tighten to the recommended torque stamped on the ring.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Lg., mm | Inside Wd., mm | Overall Ht., mm | Vertical Capacity, lbs. | Movement | Specifications Met | Each | |
Yellow Powder-Coated Steel | |||||||||
---|---|---|---|---|---|---|---|---|---|
M30 | 3.5 | 45 | 54 | 269 | 21,160 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked | 0000000 | 0000000 |
Hoist Ring Assortments—For Lifting
Keep on hand all the parts needed to assemble custom hoist rings. Ideal for angular lifting, these hoist rings will withstand stresses that bend or break eyebolts. The base of these hoist rings will swivel 360° to compensate for pitch, roll, and sway when lifting heavy or unbalanced loads. The shackle will pivot 180° front to back. All parts have a black oxide finish for mild corrosion resistance.
Install the base of these hoist rings flush to your mounting surface. Use a torque wrench to tighten to the recommended torque stamped on the ring.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
Number of Pieces | Thread Size | Movement | Includes | Specifications Met | Each | |
Black-Oxide Steel | ||||||
---|---|---|---|---|---|---|
104 | M12 M16 M20 M24 M30 | 180° Pivot and 360° Swivel | Four 3/4" Dia. Shackles Four 1" Dia. Shackles Four M12 × 1.75 mm Bolts for 3/4" Dia. Shackle—2,310 lbs. Capacity and 19 mm Thread Lg. Four M16 × 2 mm Bolts for 3/4" Dia. Shackle—4,180 lbs. Capacity and 29 mm Thread Lg. Four M20 × 2.5 mm Bolts for 3/4" Dia. Shackle—4,730 lbs. Capacity and 34 mm Thread Lg. Four M20 × 2.5 mm Bolts for 1" Dia. Shackle—6,610 lbs. Capacity and 32 mm Thread Lg. Four M24 × 3 mm Bolts for 1" Dia. Shackle—9,250 lbs. Capacity and 37 mm Thread Lg. Four M30 × 3.5 mm Bolts for 1" Dia. Shackle—9,250 lbs. Capacity and 38 mm Thread Lg. 24 Bushings 24 Retaining Rings 24 Washers | ASME B30.26 | 0000000 | 000000000 |
Rotating Eyebolts—For Lifting
Unlike conventional eyebolts, you can rotate the eye 360° to match the angle of your load.
Powder-coated steel eyebolts are impact resistant, but less corrosion resistant than stainless steel eyebolts. They include a removable key for tightening the bolt.
Note: Capacities listed are for vertical lifting only. Eyebolts with shoulder can be used for angular lifting up to 45°, but the capacities will be significantly reduced. For angular lifting, we recommend Hoist Rings.
Warning: Never use to lift people or items over people.
For technical drawings and 3-D models, click on a part number.
Thread | With Shoulder | ||||||||
---|---|---|---|---|---|---|---|---|---|
Size | Pitch, mm | Lg., mm | Shank Lg., mm | Overall Lg., mm | Eye Dia., mm | Vertical Capacity, lbs. | Color | Each | |
Powder-Coated Steel | |||||||||
M30 | 3.5 | 45 | 45 | 158 | 60 | 9,900 | Pink | 00000000 | 0000000 |
Push-On Barbed Hose Fittings for Hydraulic Fluid
These fittings have sharp barbs to grip rubber push-on hose with no clamps or ferrules required. The more you pull on the fittings, the tighter the hose will grip. Use them in low-pressure hydraulic applications up to 350 psi. Also known as hose nipples, they adapt a barbed end to a threaded end, so you can connect to pumps, cylinders, and other equipment in your hydraulic system. Fittings are zinc-plated steel, which has excellent strength and durability. Fittings have fair corrosion resistance.
Fittings that swivel until tightened rotate 360° for easy installation.
Note: To ensure proper connection, the barbed end has to be pushed in all the way, with the hose end concealed by the ring.
For technical drawings and 3-D models, click on a part number.
- Maximum Pressure: See table
- Maximum Vacuum: 28 in. of Hg @ 72° F
- Temperature Range: -40° to 155° F
- For Hose Manufacturer Series: Parker 801
Thread | Ring Stop | ||||||||
---|---|---|---|---|---|---|---|---|---|
For Hose ID | Dash Size | Size | Pitch, mm | Material | Color | Max. Pressure | Manufacturer Series | Each | |
Zinc-Plated Steel | |||||||||
3/4" | 12 | M30 | 2 | Plastic | Yellow | 300 psi @ 72° F | Parker 82 | 00000000 | 000000 |
Metric Yellow Zinc-Plated Steel Swivel Leveling Mounts with Threaded Stud
Yellow zinc-plated steel is more corrosion resistant than nickel-plated steel. Mounts have a ball-and-socket design that swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Lg., mm | Capacity per Mount, lbs. | Base Dia., mm | Overall Ht., mm | Hex Nut Wd., mm | Temperature Range, °F | Each | |
Yellow Zinc-Plated Steel | |||||||||
---|---|---|---|---|---|---|---|---|---|
M30 | 3.5 | 102 | 42,990 | 152 | 172 | 48 | -20° to 170° | 0000000 | 0000000 |
M30 | 3.5 | 152 | 42,990 | 152 | 222 | 48 | -20° to 170° | 0000000 | 000000 |
Yellow Zinc-Plated Steel with Rubber Cushion | |||||||||
M30 | 3.5 | 102 | 32,295 | 152 | 175 | 48 | -20° to 170° | 0000000 | 000000 |
M30 | 3.5 | 152 | 32,295 | 152 | 225 | 48 | -20° to 170° | 0000000 | 000000 |
Nickel-Plated Steel Swivel Leveling Mounts with Threaded Stud
Nickel-plated steel has some corrosion resistance. Mounts have a ball-and-socket design that swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Lg. | Capacity per Mount, lbs. | Base Dia. | Overall Ht. | Temperature Range, °F | Performance | Each | |
Nickel-Plated Steel | ||||||||
---|---|---|---|---|---|---|---|---|
M30 | 102mm | 42,500 | 152mm | 172mm | -20° to 170° | __ | 00000000 | 0000000 |
M30 | 152mm | 42,500 | 152mm | 222mm | -20° to 170° | __ | 00000000 | 000000 |
Nickel-Plated Steel with Rubber Cushion | ||||||||
M30 | 102mm | 32,250 | 152mm | 175mm | -20° to 170° | Antislip | 00000000 | 000000 |
M30 | 152mm | 32,250 | 152mm | 225mm | -20° to 170° | Antislip | 00000000 | 000000 |
Metric Corrosion-Resistant Swivel Leveling Mounts with Threaded Stud
Made entirely of stainless steel, these mounts resist corrosion from water and most chemicals. Their ball-and-socket design swivels to compensate for uneven floors. In addition to leveling, mounts raise equipment off the floor for easier cleaning and inspection.
Mounts with a cushion are nonskid for an extra measure of stability.
For technical drawings and 3-D models, click on a part number.
Thread Size | Thread Pitch, mm | Thread Lg., mm | Capacity per Mount, lbs. | Base Dia., mm | Overall Ht., mm | Hex Nut Wd., mm | Each | |
303 Stainless Steel | ||||||||
---|---|---|---|---|---|---|---|---|
M30 | 3.5 | 102 | 42,000 | 152 | 172 | 48 | 0000000 | 0000000 |
M30 | 3.5 | 152 | 42,000 | 152 | 222 | 48 | 0000000 | 000000 |
303 Stainless Steel with Rubber Cushion | ||||||||
M30 | 3.5 | 102 | 32,200 | 152 | 175 | 48 | 00000000 | 000000 |
M30 | 3.5 | 152 | 32,200 | 152 | 225 | 48 | 00000000 | 000000 |
Seismic Swivel Leveling Mounts
Adjust the swivels on these mounts to level equipment on uneven surfaces for protection during earthquakes. All meet NZS 4219, a New Zealand standard for seismic-rated components. Use the threaded stud to raise equipment for cleaning and inspection, and the mounting holes to bolt equipment down and keep it in place. A rubber cushion helps reduce vibration to cut down on noise, protect floors, and extend machine life. Made of 304 stainless steel, these leveling mounts won’t corrode from frequent washdowns and harsh cleaners.
For technical drawings and 3-D models, click on a part number.
Capacity per Mount, lbs. | Mounting Holes | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Thread Pitch, mm | Thread Length | Load | Pull | Base Diameter | Overall Height | Temperature Range, °F | Mounting Fasteners Included | Number of | Diameter | Center-to-Center Length | Specifications Met | Each | |
304 Stainless Steel with Rubber Cushion | ||||||||||||||
M30 | 3.5 | 7 1/8" | 13,480 | 6,290 | 5 7/8" | 11 3/8" | 0° to 230° | No | 3 | 17/32" | 4 3/32" | NZS 4219 | 00000000 | 0000000 |
M30 | 3.5 | 7 1/8" | 13,480 | 8,540 | 7 7/8" | 11 3/8" | 0° to 230° | No | 4 | 5/8" | 4 15/32" | NZS 4219 | 00000000 | 000000 |