System of Measurement System of Measurement |
|---|
|
Thread Size Thread Size | Show |
|---|
Thread Size Thread Size | Hide |
|---|
Thread Pitch Thread Pitch |
|---|
|
Vertical Capacity Vertical Capacity |
|---|
|
Fabrication Fabrication |
|---|
|
Movement Movement |
|---|
|
Material Material |
|---|
|
Pull Capacity per Mount Pull Capacity per Mount |
|---|
|
Length Length |
|---|
|
Application Application |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Finish Finish |
|---|
|
Specifications Met Specifications Met |
|---|
|
Body Style Body Style |
|---|
 | With Shoulder |
Threading Threading |
|---|
 | Fully Threaded |
Inside Width Inside Width |
|---|
|
Base Material Base Material |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
About Leveling Mounts
More
About Lifting with Hoist Rings
More
Hoist Rings—For Lifting
Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back and a base that swivels 360° to compensate for pitch, roll, and sway when lifting heavy or unbalanced loads. Install the base of the hoist ring flush to the mounting surface and tighten to the recommended torque that is stamped on the ring. Torque Wrenches are sold separately.
Black-oxide steel offers mild corrosion resistance.
Hoist rings that are CE marked meet European requirements for health, safety, and environmental protection.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
For technical drawings and 3-D models, click on a part number.
| Thread Size | Thread Pitch, mm | Thread Lg., mm | Inside Wd., mm | Overall Ht., mm | Vertical Capacity, lbs. | Movement | Specifications Met | Each | |
Forged Black-Oxide Steel | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| M36 | 4 | 67 | 101 | 302 | 24,250 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 0000000 | 0000000 |
Rotating Eyebolts—For Lifting
Unlike conventional eyebolts, you can rotate the eye 360° to match the angle of your load.
Powder-coated steel eyebolts are impact resistant, but less corrosion resistant than stainless steel eyebolts. They include a removable key for tightening the bolt.
Note: Capacities listed are for vertical lifting only. Eyebolts with shoulder can be used for angular lifting up to 45°, but the capacities will be significantly reduced. For angular lifting, we recommend Hoist Rings.
Warning: Never use to lift people or items over people.
For technical drawings and 3-D models, click on a part number.
Thread | With Shoulder | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| Size | Pitch, mm | Lg., mm | Shank Lg., mm | Overall Lg., mm | Eye Dia., mm | Vertical Capacity, lbs. | Color | Each | |
Powder-Coated Steel | |||||||||
| M36 | 4 | 54 | 54 | 190 | 73 | 15,400 | Pink | 00000000 | 0000000 |
Seismic Swivel Leveling Mounts
Adjust the swivels on these mounts to level equipment on uneven surfaces for protection during earthquakes. All meet NZS 4219, a New Zealand standard for seismic-rated components. Use the threaded stud to raise equipment for cleaning and inspection, and the mounting holes to bolt equipment down and keep it in place. A rubber cushion helps reduce vibration to cut down on noise, protect floors, and extend machine life. Made of 304 stainless steel, these leveling mounts won’t corrode from frequent washdowns and harsh cleaners.
For technical drawings and 3-D models, click on a part number.
Capacity per Mount, lbs. | Mounting Holes | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Thread Size | Thread Pitch, mm | Thread Length | Load | Pull | Base Diameter | Overall Height | Temperature Range, °F | Mounting Fasteners Included | Number of | Diameter | Center-to-Center Length | Specifications Met | Each | |
304 Stainless Steel with Rubber Cushion | ||||||||||||||
| M36 | 4 | 7 1/8" | 21,580 | 6,290 | 5 7/8" | 11 3/8" | 0° to 230° | No | 3 | 17/32" | 4 3/32" | NZS 4219 | 00000000 | 0000000 |
| M36 | 4 | 7 1/8" | 21,580 | 8,540 | 7 7/8" | 11 3/8" | 0° to 230° | No | 4 | 5/8" | 4 15/32" | NZS 4219 | 00000000 | 000000 |