System of Measurement System of Measurement |
|---|
|
Thread Size Thread Size | Show |
|---|
Thread Size Thread Size | Hide |
|---|
Thread Pitch Thread Pitch |
|---|
|
Movement Movement |
|---|
 |  |
| 180° Pivot | 360° Swivel |
Vertical Capacity Vertical Capacity |
|---|
|
Material Material |
|---|
|
Specifications Met Specifications Met |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Application Application |
|---|
|
Fabrication Fabrication |
|---|
|
Inside Width Inside Width |
|---|
|
Finish Finish |
|---|
|
Base Material Base Material |
|---|
|
Mount Movement Mount Movement |
|---|
 | Swivel |
Swivel Range of Motion Swivel Range of Motion |
|---|
|
Pull Capacity per Mount Pull Capacity per Mount |
|---|
|
Cushion Color Cushion Color |
|---|
 | Black |
Load Capacity per Mount Load Capacity per Mount |
|---|
|
About Leveling Mounts
More
About Lifting with Hoist Rings
More
Hoist Rings—For Lifting
Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back and a base that swivels 360° to compensate for pitch, roll, and sway when lifting heavy or unbalanced loads. Install the base of the hoist ring flush to the mounting surface and tighten to the recommended torque that is stamped on the ring. Torque Wrenches are sold separately.
Machined hoist rings have a smooth finish to protect slings and hooks from damage and excess wear during lifting.
Black-oxide steel offers mild corrosion resistance.
Hoist rings that are CE marked meet European requirements for health, safety, and environmental protection.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
For technical drawings and 3-D models, click on a part number.
| Thread Size | Thread Pitch, mm | Thread Lg., mm | Inside Wd., mm | Overall Ht., mm | Vertical Capacity, lbs. | Movement | Specifications Met | Each | |
Machined Black-Oxide Steel | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| M42 | 4.5 | 79 | 114 | 396 | 27,550 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 00000000 | 0000000 |
Seismic Swivel Leveling Mounts
Adjust the swivels on these mounts to level equipment on uneven surfaces for protection during earthquakes. All meet NZS 4219, a New Zealand standard for seismic-rated components. Use the threaded stud to raise equipment for cleaning and inspection, and the mounting holes to bolt equipment down and keep it in place. A rubber cushion helps reduce vibration to cut down on noise, protect floors, and extend machine life. Made of 304 stainless steel, these leveling mounts won’t corrode from frequent washdowns and harsh cleaners.
For technical drawings and 3-D models, click on a part number.
Capacity per Mount, lbs. | Mounting Holes | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Thread Size | Thread Pitch, mm | Thread Length | Load | Pull | Base Diameter | Overall Height | Temperature Range, °F | Mounting Fasteners Included | Number of | Diameter | Center-to-Center Length | Specifications Met | Each | |
304 Stainless Steel with Rubber Cushion | ||||||||||||||
| M42 | 4.5 | 7 5/16" | 31,470 | 6,290 | 5 7/8" | 11 3/4" | 0° to 230° | No | 3 | 17/32" | 4 3/32" | NZS 4219 | 00000000 | 0000000 |
| M42 | 4.5 | 7 5/16" | 31,470 | 8,540 | 7 7/8" | 11 3/4" | 0° to 230° | No | 4 | 5/8" | 4 15/32" | NZS 4219 | 00000000 | 000000 |