The T-handle provides a good grip for your whole hand and the long shaft reaches into tight spots.

When working in tight spaces, these short keys fit where others can't.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

The textured grip provides comfort, slip resistance, and maximum torque. These keys have a long shaft for reaching into tight spots to turn fasteners.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places. These keys have a textured grip that provides comfort, slip resistance, and maximum torque.

With a simple loop handle, these keys are the economical choice. They have a long shaft for reaching into tight spots and the T-handle provides a good grip for your whole hand when turning fasteners.

The long shaft has a ball end for angled entry to turn screws in hard-to-reach areas. The short shaft provides additional torque.

Use the long shaft for more reach and the short shaft for more torque when turning fasteners.

The extra-long shaft lets you access fasteners in deep recesses. To change tips, use a hex key to loosen the set screw.

The ball-end tip has a retaining ring that grips inside the recess to hold screws in place and allows angled entry to turn fasteners in hard-to-reach areas.

Protect your stainless steel screws by using a stainless steel key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Sets include an assortment of keys with a long shaft for more reach and a short shaft for more torque. Use stainless steel keys to protect your stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

These assorted keys have a retaining ring on the tip that grips inside the recess to hold screws in place. Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC and ASTM standards. They have a long shaft that reaches into tight spots to turn fasteners.

Bits are held in place with a retaining ring or set screw rather than a magnet, so the tool won't attract loose metal parts and shavings.

The ratcheting mechanism turns sockets quickly.

Turn sockets from above when there's not room to swing a standard wrench handle.

Also known as tank-strap bolts, these T-bolts are commonly used with a band clamp or a strap to hold fuel tanks and other objects in place.

For a more secure hold than standard quick-release pins, these pins lock in place until you push the button to release the spring-loaded retaining balls.

A T-handle makes these pins easy to grip. Made entirely of stainless steel, they stand up to corrosive enviroments. Pins lock in place until you push the button to release the spring-loaded retaining balls.

Also known as double-acting pins, these pins lock in place until you push or pull the handle to release the spring-loaded retaining balls. The T-handle is easy to grip.

A T-handle makes these pins easy to grip. The shoulder keeps a portion of the pin outside the hole and makes them easy to grab.

A quarter turn of the handle locks these plungers in the retracted position. The T-handle is easy to grip.

Install these knobs on a threaded stud. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Long shafts can thread through these knobs for mounting versatility. The knobs provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

To build a custom knob or thumb screw, pair one of these knobs with a hex or socket head screw. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Also known as compression cam latches, turn the handle a quarter-turn to latch, then another quarter-turn to draw the cam firmly against the door or drawer surface.

The mounting screws on these latches are concealed to prevent tampering.

Designed for food-processing and hygienic applications, these corrosion-resistant latches are FDA compliant for direct food contact and DGUV tested to meet European regulations for use with food.

Use these latches in a 3/4" dia. through hole, which is the most common through-hole size.

Also known as compression cam locks, turn the handle a quarter-turn to latch, then another quarter-turn to draw the cam firmly against the door or drawer surface.

The mounting screws on these locks are concealed to prevent tampering.

In addition to an IP65 rating for low-pressure washdown environments, these locks have a squeeze-release handle to prevent accidental opening when unlocked.

The mounting screws on these locks are concealed to prevent tampering.

Use these latches alone for single-point latching, or add latch kits for more holding power.

Use these valves in general purpose applications such as those with water, oil, air, and inert gas.

A built-in strainer traps debris and allows you to replace the screen without disconnecting your pipeline.

These valves can handle at least twice the pressure of other compact valves. Install them in tight spots. Use with water, oil, air, and inert gas.

These valves have union fittings that disassemble for fast installation and removal from pipelines. Use with water, air, and inert gas.

Plastic provides a lightweight and economical alternative to metal. All valves have barbs that grip onto tubing for a secure hold. They’re for use with water, oil, air, and inert gas.

Attach these valves to industry-standard two-bolt flanges on circulation pumps from manufacturers such as Bell and Gossett, Taco, Grundfos, and Armstrong. Use with water, air, and steam.

With 45° flared tube fittings, these valves form a tight seal on metal tubing lines for natural gas, propane, and butane.

For fast installation and removal from pipelines, these valves have union fittings that disassemble into multiple pieces. All have a fluoroelastomer seal and a plastic body that can stand up to aggressive and corrosive solutions in chemical-processing applications.

For chemical-processing applications in confined areas, these valves have an EPDM seal and a PVC or CPVC body to withstand aggressive and corrosive solutions and a low-profile handle to fit in tight spots.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves have a fluoroelastomer seal and a plastic body that can withstand aggressive and corrosive solutions in chemical-processing applications.

For use in drinking water systems, these valves meet NSF/ANSI 61.

Disassemble the union fittings on these valves for fast installation and removal from your pipeline. All meet NSF/ANSI 61 for use with drinking water.

Often used in hydraulic and compressed air systems, these valves can withstand at least 6,000 psi. They’re for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Also known as block and bleed valves, these have two vent ports to isolate pressure gauges, switches, and other components in high-pressure systems for maintenance, calibration, and sampling without interrupting the process. They are rated for up to 10,000 psi. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Also known as block and bleed valves, these have a vent port that allows you to remove instrumentation equipment attached to the valve without depressurizing your line. Turn the handle to shut off flow and remove the vent port plug to drain liquid trapped in the valve. Use them with water, oil, air, and inert gas. These valves adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Rated for nearly twice the maximum temperature of standard threaded precision flow-adjustment valves, these can handle up to 700° F. They’re for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

A compression sleeve bites into tubing as you tighten the nut, forming a strong seal. These valves are for use with air. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Solder these valves to tubing for a permanent, leak-tight connection. Use them with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

To withstand a maximum steam pressure of at least 4,800 psi @ 355° F in applications such as petroleum refineries, these valves are machined from a single piece of metal for seamless construction. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Divert the flow of compressed air and other media to multiple pieces of equipment. Use with water, oil, air, and inert gas.

For easy installation and removal from pipelines, all ends on these valves have union fittings that disassemble into multiple pieces. Their fluoroelastomer seal and plastic body can withstand aggressive and corrosive solutions for diverting flow between ports in chemical-processing applications.

To divert flow between ports in drinking water lines, these valves meet NSF/ANSI 61.