A nonreflective black oxide finish prevents glare that can interfere with machine vision systems.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

The handle locks in a horizontal position for more clearance above the clamp than standard hold-down toggle clamps.

Hold workpieces of different thicknesses without adjustment.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Push the lever to lock the handle and prevent accidental opening.

Weld these clamps to the side of an object or drill your own holes in the mounting plate and bolt into place.

Two sets of mounting holes allow mounting on the bottom or side.

The mounting base secures these clamps to a rail or bar.

These clamps have mounting holes on the bottom.

Suitable for production applications, these clamps have double the service life of other air-powered toggle clamps.

Mount the base to a work surface using screws.

Smaller than standard push/pull toggle clamps, these are often used for electronics and small fixturing applications.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Smaller than standard push toggle clamps, these are often used for electronics and small fixturing applications.

The handle can be rotated 125° for easier access or extra clearance above the clamp.

Push the lever to lock the handle and prevent accidental opening.

Secure these clamps to a rail or bar.

Eliminating the need for step blocks or other rear support, the pivoting rocker clamps workpieces of various thicknesses.

The stepped end provides support and quick height adjustment when paired with a step block.

Get everything needed for basic workholding on a machine table.

Designed to provide more clearance above the nut than standard clamps, these have an offset shape. Also known as gooseneck clamps.

A plastic pad on the gripping surface of these clamps prevents workpiece marring, making them useful for holding polished surfaces and reducing the need for secondary finishing steps.

Making minimal contact with the workpiece while holding securely, these clamps are good for small parts and can clamp into holes and notches.

Unlike other setup clamps that grip the horizontal surface of a workpiece, these clamps have a pivoting ball in the tip to get a firm hold on angled parts.

The built-in T-slot nut on these side clamps lets you clamp a part to a machine table quickly. Their small footprint leaves more free space on your table than standard side clamps.

An alternative to setup clamps, these heavy duty clamps have high holding power to secure workpieces during machining.

Mount using the holes in the base.

Use the power of hydraulic fluid to quickly, consistently, and repeatedly clamp and release parts with a greater clamping force than air-powered hold-down fixture clamps.

Machine these clamps to match the contours of your workpiece and turn the screw to grip.

Install these clamps into a slot in your fixture to grip at the bottom of a workpiece edge, giving the cutting tool maximum access.

Set one of these clamps between two workpieces in a fixture and tighten the screw to push the clamp's sides out for a secure hold.

Secure a workpiece from the inside, leaving the outside clear for machining.

Build these components into fixture plates, machine subplates, and tombstones for quick changes. The system clamps and locates at the same time for accurate positioning with repeatability of ±0.0005".

Push the lever to lock the handle and prevent accidental opening.

Mount the clamp on a lid and the latch plate on the side of a container.

With five times the capacity of standard corner clamps, these secure two workpieces at a 90° angle.

The clamping surfaces pivot individually to secure workpieces of different thicknesses at any angle from 5° to 180°.

Use the switch to engage and disengage the magnet for easy placement and removal of your workpiece.

Each arm has a handle for turning the magnets on and off.

Clamp workpieces from the outside at a 90° angle, leaving the inside free for welding or fabrication.

A removable, heavy duty steel base plate provides a flat, durable clamping surface. Carry it where needed or mount the base plate to your workbench.