Use the extra-long shank to thread deep and hard-to-reach holes.

Sized to cut oversized threads, these tools are often used to tap holes where the threads will shrink due to heat treatment or plating.

Use these taps on hard and abrasive material, such as heat-treated metal, nickel, and fiberglass.

Clear chips while tapping deep and hard-to-reach holes. These taps have an extra-long shank for extended reach.

These taps cut left-hand threads while keeping chips clear.

Also known as cold-forming and fluteless taps, these press threads into material without cutting it, so no chips are created.

Insert these taps directly into drills, power screwdrivers, and other tools that accept a 1/4" hex shank.

With a taper chamfer and bottoming chamfer at opposite ends, these taps start threads easily and are good for threading close to the bottom of closed-end holes.

Coated with chromium carbide or titanium carbonitride (TiCN), these cobalt steel taps cut smoothly through soft material to produce accurate threads.

To tap nickel and other hard material, these cobalt steel taps have high cutting strength. Their flutes are designed to keep chips clear, so they don't need to be reversed to prevent buildup.

With an extra-long shank, these taps have extended reach for tapping deep and hard-to-reach areas in pipe and conduit.

Use these carbon steel taps for thread repair and occasional tapping of pipe and conduit. They can tap threads into most metal and plastic, but they have a shorter tool life than standard taps.

Also known as short-projection taps, these have fewer tapered threads at the tip than standard pipe taps, so you don't have to drive them as deep to produce full threads.

Drill and thread holes for pipe and conduit without switching tools.

The cutting teeth are shaped to cut smooth threads in soft pipe and conduit material.

Cut threads in PG thread sizes commonly used for European conduit.

Connect a tap to these wrenches for occasional or light-duty hand tapping. All have a T-handle design, so they're more compact than straight-handle tap wrenches but provide less leverage.

Use with a tap to thread holes by hand. These tools have long handles to provide more leverage than T-handle wrenches, but they require more space for tapping.

Also known as hand tappers, these wrenches mount to a flat surface for stability and guide the tap straight into the hole for accurate threading.

These holders work like sockets to connect taps to ratchet wrenches.

Connect these extensions to your tap for greater access to hard-to-reach areas. Sets include nine extensions to fit different tap sizes.

Drawers and labeled compartments provide space for keeping tools organized. Taps and drill bits are not included.

Keep taps and drill bits organized. All holes are labeled with sizes. Taps and drill bits are not included.

One file restores a range of thread sizes in most hole diameters.

Attach these tools to a socket wrench to restore rusted and damaged spark plug threads in two common sizes.

With replaceable dies, these long-lasting tools can repair both screw threads and pipe and conduit threads. Use them for holes with an ID from 3/4" to 6".

After using a large-diameter bit to drill a starter hole in a broken tap, drill out the tap with one of these tools.

To extract taps of different sizes, these sets include multiple extractors. Use them with a tap wrench to remove taps with straight flutes from the workpiece without damaging the surrounding threads.

For use with a wide range of threaded hole diameters, these sets include multiple retrievers. Insert the retriever into a tapped hole and pull out to remove chips.

For start-to-finish tapping of left-hand threads, these sets include one taper-, one plug-, and one bottoming-chamfer tap.

Multiple tap sizes allow tapping a range of hole diameters. Connect these taps directly to drills, power screwdrivers, and other tools that accept a 1/4" hex shank.

Drill and tap a variety of hole sizes. These taps and drill bits are for use on metal and plastic.

All taps and drill bits have a hex shank for direct connection to tools such as drills and power screwdrivers.

Cut and repair threads and drill holes in many different sizes. Tap and die wrenches are included.

Switch from internal to external threading with interchangeable tap and die adapters. Use them with the included ratcheting wrench.

Multiple files and handles are included in these sets.

Slide over the end of threaded rod, pipe, and conduit to the area where threads are damaged, then tighten and rotate to repair threads.

Assortments include various sizes of helical inserts and a tap, a drill bit, and an installation tool for each thread size.

These kits have short-, normal-, and long-reach inserts, an installation tool, and a tap.

Place on your workpiece.

Also known as tap chucks, these fit into machines that have a Morse taper spindle.

Use to attach taps to Procunier auto-reversing tap holders.