6-48 Taps | McMaster-Carr

After using a large-diameter bit to drill a starter hole in a broken tap, drill out the tap with one of these tools. Sets include multiple extractors for use with different tap sizes and two picks for removing the remains.

No. of Pieces	Includes	For Tap Size	Overall Lg.	OD	Material	Container Type		Each
7	Four Tap Extractors, Pin Vise, Two Picks	No. 4, No. 5, No. 6, No. 8, No. 10, No. 12, 1/4", 5/16", 3/8", 7/16", 1/2", M3, M3.5, M4, M5, M6, M7, M8, M10, M12	1 1/4" 1 1/2" 2" 2 1/2"	1/8" 5/64" 3/16" 1/4"	Carbide	Plastic Case	0000000	0000000

Tap Sets

These sets include a variety of taps for threading holes so screws, bolts, and rods fit snugly.

High-Speed Steel—Single Thread Size Sets

Taper, Plug, and Bottoming

Chamfer Set

The most versatile taps resist heat and wear to stay sharp. They’re good for most metals and plastic. These sets include one of each chamfer type: Taper for starting holes and threading through holes; plug for through holes and blind holes; and bottoming for cutting the closest to the bottom of any hole.

Uncoated—The economical choice, these won't last as long as coated taps.

							Taper Chamfer, Plug Chamfer, Bottoming Chamfer
	No. of Pieces	Thread Size	Thread Type	Container Type	No. of Flutes	Shank Type		Each
Uncoated



		3	6-48	UNS	Plastic Case	3	Square	00000000	000000

Carbon Steel—Single Thread Size Sets

Taper, Plug, and Bottoming

Chamfer Set

The economical choice for occasional hand tapping. These work on most metals and plastic but will dull more quickly than other taps. Sets include one each chamfer type: Taper for starting holes and through holes; plug for through holes and blind holes; and bottoming for cutting the closest to the bottom of any hole.

							Taper Chamfer, Plug Chamfer, Bottoming Chamfer
	No. of Pieces	Thread Size	Thread Type	Container Type	No. of Flutes	Shank Type		Each
Uncoated



		3	6-48	UNS	Plastic Case	3	Square	000000000	00000

Tap Extractor Sets for Screw Thread Taps

To extract taps of different sizes, these sets include multiple extractors. Fingers on the extractor grip the flutes on a broken tap. Use with a tap wrench to remove taps with straight flutes from the workpiece.

No. of Pieces	For Three-Flute Tap Size	For Four-Flute Tap Size	Material	Container Type	For Number of Tap Flutes	Each
11	No. 5, No. 6, 1/8", M3, M3.5	No. 8, No. 10, No. 12, No. 14, 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 15/32", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16", 7/8", 15/16", 1", M4, M4.5, M5, M5.5, M6, M6.3, M7, M8, M9, M10, M11, M12, M12.5, M14, M16, M18, M19, M20, M22, M24, M25	Steel	Plastic Case	3, 4	0000000
13	No. 4, No. 5, No. 6, 1/8", M3, M3.5	No. 8, No. 10, No. 12, No. 14, 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 15/32", 1/2", 9/16", 5/8", 11/16", 3/4", M4, M4.5, M5, M5.5, M6, M6.3, M7, M8, M9, M10, M11, M12, M12.5, M14, M16, M18, M19, M20	Steel	Plastic Case	3, 4	000000
15	No. 4, No. 5, No. 6, 1/8", M3, M3.5	No. 8, No. 10, No. 12, No. 14, 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 15/32", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16", 7/8", 15/16", 1", M2, M4, M4.5, M5, M5.5, M6, M6.3, M7, M8, M9, M10, M11, M12, M12.5, M14, M16, M18, M19, M20, M22, M24, M25	Steel	Plastic Case	3, 4	000000

Taps

Cut threads into holes so screws, bolts, and rods fit snugly. Our basic taps have straight flutes that are good for most jobs.

High-Speed Steel—The most versatile taps resist heat and wear to stay sharp. They’re good for most metals and plastic.

Uncoated—The economical choice, these won't last as long as coated taps.

Taper Chamfer—Good for both starting holes and threading through holes. These taps have the longest taper to gradually engage with the material, reducing the force needed to turn them. They can't reach the bottom of blind holes, however, so you will likely need to finish with a bottoming-chamfer tap.

Plug Chamfer—Our go-to chamfer type, these thread both through holes and blind holes. The tapered section is shorter than a taper chamfer and longer than bottoming chamfer. As a result, they're easier to turn than bottoming taps but require more force than taper taps.

Bottoming Chamfer—Cut all the way to the bottom of blind holes with taps that have the shortest taper. Since these require the most force to turn, they’re often used to finish holes started by taper- or plug-chamfer taps.

Number of Flutes—Taps with fewer flutes have more space to capture chips, so you won’t have to clear them as often. However, they can be more difficult to keep straight in the hole.

Taps Sold as Sets—Include one tap of each chamfer type.

	Taps														Taps Sold as Sets
						Drill Bit			Taper Chamfer		Plug Chamfer		Bottoming Chamfer
	Thread Size	Thread Lg.	Overall Lg.	Thread Type	No. of Flutes	Size, mm	Decimal Size Equiv.	Shank Type		Each		Each		Each	No. of Taps		Each
High-Speed Steel







				Uncoated

				6-48	11/16"	2"	UNS	3	2.9	0.1142"	Square	00000000	000000	00000000	000000	00000000	000000	3	00000000	000000

Chip-Clearing Taps

Spiral-Point Flute for Through Holes

Remove long, stringy chips to produce cleaner threads than standard taps. The flute design prevents buildup to protect the quality of the threads and avoid damage to the tap. Since you don’t need to reverse these taps to extract chips, they also create threads faster.

High-Speed Steel—The most versatile taps resist heat and wear to stay sharp. They’re good for most metals and plastic.

Uncoated—The economical choice, these won't last as long as coated taps.

Titanium Nitride (TiN) Coated—Run at higher speeds and last twice as long as uncoated taps.

Titanium Carbon Nitride (TiCN) Coated—Resist heat, chipping, and wear for three times the life of uncoated taps.

Spiral-Point Flute for Through Holes—Push chips ahead of the tap and out of through holes. Also known as gun taps.

Plug Chamfer—Our go-to chamfer type. With a longer taper than a bottoming chamfer, they are easier to turn but won't thread as close the bottom of a hole.

					Drill Bit			Spiral-Point Flute for Through Holes
	Thread Size	Thread Lg.	Overall Lg.	Thread Type	Size, mm	Decimal Size Equiv.	Shank Type	Chamfer Type	No. of Flutes		Each
High-Speed Steel







				Uncoated

				6-48	11/16"	2"	UNS	2.9	0.1142"	Square	Plug	2	00000000	000000




						Titanium Nitride (TiN) Coated

						6-48	45/64"	2"	UNS	2.9	0.1142"	Square	Plug	2	00000000	00000




								Titanium Carbon Nitride (TiCN) Coated

								6-48	23/32"	2"	UNS	2.9	0.1142"	Square	Plug	2	00000000	00000

Drill Out Tap Extractors for Screw Thread Taps

After using a large-diameter bit to drill a starter hole in a broken tap, drill out the tap with one of these tools. Remove the remains with a scriber or pick.

For Tap Size	OD	Overall Lg.	Material		Each
No. 4, No. 5, No. 6, M3, M3.5	5/64"	1 1/4"	Carbide	0000000	000000

Tap Extractors for Screw Thread Taps

Fingers on the extractor grip the flutes on a broken tap. Use with a tap wrench to remove taps with straight flutes from the workpiece without damaging the surrounding threads.

Tap Extractors						Replacement Tap Extractor Fingers
For Tap Size	Material	Square Shank Size	Choose a Number of Tap Flutes		Each	Choose a Number of Tap Flutes	Pkg. Qty.		Pkg.
No. 6, M3.5	Steel	0.092"	2 , 3 , 4	00000000	000000	2 , 3 , 4	12	00000000	000000