Drill holes and cut threads without switching tools. Made of high-speed steel, these taps are for use on most metal and plastic. The square shank is compatible with tap holders for drill presses and milling machines. All have a plug chamfer with 3-5 chamfered cutting threads, so they're suitable for start-to-finish tapping.

Taps with spiral flutes keep chips clear by drawing them back toward the tap and out of the hole.

Uncoated taps are strong enough for most tapping jobs but have a shorter tool life.

For technical drawings and 3-D models, click on a part number.

These taps are made of cobalt steel for higher strength and wear resistance than standard taps. Their flutes are designed to keep chips clear, so they don't need to be reversed to prevent buildup. With a square shank, they're compatible with tap wrenches and tap holders for drill presses and milling machines. All have a plug chamfer with 3-5 chamfered cutting threads, so they're suitable for start-to-finish tapping.

Taps for through-hole threading have spiral-point flutes, which push chips ahead of the tap and out of through holes. They're also known as gun taps.

For technical drawings and 3-D models, click on a part number.

To tap nickel and other hard material, these cobalt steel taps have high cutting strength. Their spiral flutes keep chips clear, so they don't need to be reversed to prevent buildup. With a square shank, they're compatible with tap wrenches and tap holders for drill presses and milling machines. All have a plug chamfer with 3-5 chamfered cutting threads, so they're suitable for start-to-finish tapping.

Taps for through-hole threading push chips ahead of the tap and out of through holes.

For technical drawings and 3-D models, click on a part number.

A high helix angle provides the cutting strength needed to tap threads in titanium. These cobalt steel taps have an open flute design that keeps chips clear, so they don't need to be reversed to prevent buildup. With a square shank, they're compatible with tap holders for drill presses and milling machines. All have a plug chamfer with 3-5 chamfered cutting threads, so they're suitable for start-to-finish tapping.

Taps for closed-end hole threading have right-hand spiral flutes. They draw chips back toward the tap while cutting threads to prevent chip accumulation in closed-end holes.

For technical drawings and 3-D models, click on a part number.

These taps are for use on most metal and plastic. They have a square shank that's compatible with tap wrenches and tap holders for drill presses and milling machines.

Use uncoated high-speed steel taps for small-scale tapping jobs. Titanium-nitride (TiN) coated high-speed steel taps resist heat and wear better than uncoated taps, letting them last up to twice as long.

Taper-chamfer taps have 7-10 chamfered threads at the tip for cutting into the workpiece. They require less torque than other chamfer types, making them a good choice for starting threads and tapping through holes. However, a longer taper means that they cannot thread as close to the bottom of closed-end holes.

Plug-chamfer taps are a versatile choice for most tapping applications. With 3-5 chamfered cutting threads, they require moderate torque and are often used for start-to-finish tapping of through holes and closed-end holes. However, they do not start threads as easily as taper chamfers. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.

Bottoming-chamfer taps cut into the workpiece with just 1-2 chamfered threads. This short chamfer lets them thread holes closer to the bottom than other taps, but they require more torque to start threads.

For technical drawings and 3-D models, click on a part number.

Sets include multiple tap sizes for threading different hole diameters. Also known as gun taps, all have spiral-point flutes that push chips ahead of the tap and out of through holes. Because they don't need to be reversed to prevent buildup, they produce threads more efficiently than standard taps and are suitable for production work. They're made of high-speed steel and are for use on most metal and plastic. With a square shank, they're compatible with tap wrenches and tap holders for drill presses and milling machines. Their plug chamfer starts threads with moderate torque and is good for start-to-finish tapping.

Taps with a gold-oxide finish produce less friction than uncoated taps, but do not last as long as titanium-nitride (TiN) coated taps.

For technical drawings and 3-D models, click on a part number.