M9 Taps | McMaster-Carr

Cut and repair threads and drill holes in many different sizes. Tap and die wrenches are included. The dies are hex shaped for use with conventional wrenches. The taps are made of carbon steel and are recommended for thread repair and occasional tapping.

Taper Chamfer—Taper chamfer taps have 7-10 chamfered threads at the tip for cutting into the workpiece. They require less torque than other chamfer types, making them a good choice for starting threads and tapping through holes. However, a longer taper means that they cannot thread as close to the bottom of closed-end holes.

Plug Chamfer—Plug chamfer taps are a versatile choice for most tapping applications. With 3-5 chamfered cutting threads, they require moderate torque and are often used for start-to-finish tapping of through holes and closed-end holes. However, they do not start threads as easily as taper chamfers. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.

	Drill Bit Sizes Included	Container Type	Includes	Tap Chamfer Type		Each
Carbon Steel







	Right-Hand Thread

	117	4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/8"-28, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/8"-28, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	5/64", 7/64", 5/32", 1/4", 19/64", 5/16", 21/64", 3/8", 25/64", 13/32", 27/64", 29/64", 43 ga., 39 ga., 36 ga., 30 ga., 29 ga., 25 ga., 21 ga., 20 ga., 16 ga., 9 ga., 7 ga., 3 ga., B, F, H, I, J, O, Q, R, S, U, Z	Plastic Case	Die Wrench (2), Extractor (5), Tap Wrench (3), Thread Gauge (2)	Taper, Plug	00000000	0000000

Tap Sets

These sets include a variety of taps for threading holes so screws, bolts, and rods fit snugly.

High-Speed Steel—Single Thread Size Sets

Taper, Plug, and Bottoming

Chamfer Set

The most versatile taps resist heat and wear to stay sharp. They’re good for most metals and plastic. These sets include one of each chamfer type: Taper for starting holes and threading through holes; plug for through holes and blind holes; and bottoming for cutting the closest to the bottom of any hole.

Uncoated—The economical choice, these won't last as long as coated taps.

							Taper Chamfer, Plug Chamfer, Bottoming Chamfer
	No. of Pieces	Tap Sizes Included	Thread Type	Container Type	No. of Flutes	Shank Type		Each
Uncoated



		3	M9	Metric	Plastic Case	4	Square	000000000	000000


		3	M9	Metric	Plastic Case	4	Square	000000000	000000

Carbon Steel—Multiple Thread Size Sets

Plug Chamfer Set

The economical choice for occasional hand tapping. These work on most metals and plastic but will dull more quickly than other taps. Sets include multiple sizes of plug chamfer taps for through holes and blind holes.

						Plug Chamfer
	No. of Pieces	Tap Sizes Included	Thread Type	Container Type	Shank Type		Each
Uncoated



		113	5 each of sizes M3 × 0.50 mm, M3 × 0.60 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm; M12 × 1.25 mm, M12 × 1.50 mm, and M12 × 1.75 mm, 1 each of sizes M14 × 1.25 mm, M14 × 1.50 mm; M5 × 0.90 mm, M6 × 1.00 mm, M6.3 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm; M9 × 0.75 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.00 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm; M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 2.50 mm, M20 × 2.50 mm, and M24 × 3.00 mm	Metric	Plastic Case	Square	0000000	0000000

Tap and Die Sets

Use a single set for many sizes of internal and external threads. The taps and dies are for use on most metal and plastic.

Carbon Steel—Carbon steel taps are for thread repair and occasional tapping.

Plug Chamfer—Plug-chamfer taps are a versatile choice for most tapping applications. With 3-5 chamfered cutting threads, they require moderate torque and are often used for start-to-finish tapping of through holes and closed-end holes. However, they do not start threads as easily as taper-chamfer taps. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.

Taper Chamfer—Taper-chamfer taps have 7-10 chamfered threads at the tip for cutting into the workpiece. They require less torque than other chamfer types, making them a good choice for starting threads and tapping through holes. However, a longer taper means that they cannot thread as close to the bottom of closed-end holes.

Hex—Hex-shaped dies are for thread repair and can be used with conventional wrenches.

	Die Shape	Die Sizes Included	Wd.	Container Type	Includes		Each
Carbon Steel Taps and Dies







	Right-Hand Thread

	24	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M5 × 0.80 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.25 mm, M10 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	Plug, Taper	Hex	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M5 × 0.80 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.25 mm, M10 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	1"	Plastic Case	Die Wrench, Tap Wrench	00000000	0000000


	40	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	Plug, Taper	Hex	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	5/8", 1"	Plastic Case	Die Wrench (2), Tap Wrench (3), Thread Gauge	0000000	000000
	52	1/4"-19, 1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.25 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, M18 × 2.50 mm	Plug, Taper	Hex	1/8"-28, 1/4"-19, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.25 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, M18 × 2.50 mm	1", 1 7/16"	Plastic Case	Die Wrench (2), Tap Wrench (3), Thread Gauge	0000000	000000
	65	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.25 mm, M14 × 1.50 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, M18 × 2.50 mm, M20 × 2.50 mm, M22 × 1.50 mm, M24 × 2.00 mm, M24 × 3.00 mm	Plug, Taper	Hex	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.25 mm, M14 × 1.50 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, M18 × 2.50 mm, M20 × 2.50 mm, M22 × 1.50 mm, M24 × 2.00 mm, M24 × 3.00 mm	5/8", 1", 1 3/16", 1 7/16", 1 13/16"	Plastic Case	Die Wrench (4), Tap Wrench (4), Thread Gauge	0000000	000000

Tap Extractor Sets for Screw Thread Taps

To extract taps of different sizes, these sets include multiple extractors. Fingers on the extractor grip the flutes on a broken tap. Use with a tap wrench to remove taps with straight flutes from the workpiece.

No. of Pieces	For Three-Flute Tap Size	For Four-Flute Tap Size	Material	Container Type	For Number of Tap Flutes	Each
6	—	No. 10, No. 12, No. 14, 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 15/32", 1/2", M4.5, M5, M5.5, M6, M6.3, M7, M8, M9, M10, M11, M12, M12.5	Steel	Plastic Case	4	0000000
6	—	No. 14, 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 15/32", 1/2", 9/16", 5/8", M6, M6.3, M7, M8, M9, M10, M11, M12, M12.5, M14, M16	Steel	Plastic Case	4	000000
6	—	5/16", 11/32", 3/8", 7/16", 15/32", 1/2", 9/16", 5/8", M7, M8, M9, M10, M11, M12, M12.5, M14, M16	Steel	Plastic Case	4	000000
11	No. 5, No. 6, 1/8", M3, M3.5	No. 8, No. 10, No. 12, No. 14, 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 15/32", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16", 7/8", 15/16", 1", M4, M4.5, M5, M5.5, M6, M6.3, M7, M8, M9, M10, M11, M12, M12.5, M14, M16, M18, M19, M20, M22, M24, M25	Steel	Plastic Case	3, 4	000000
13	No. 4, No. 5, No. 6, 1/8", M3, M3.5	No. 8, No. 10, No. 12, No. 14, 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 15/32", 1/2", 9/16", 5/8", 11/16", 3/4", M4, M4.5, M5, M5.5, M6, M6.3, M7, M8, M9, M10, M11, M12, M12.5, M14, M16, M18, M19, M20	Steel	Plastic Case	3, 4	000000
15	No. 4, No. 5, No. 6, 1/8", M3, M3.5	No. 8, No. 10, No. 12, No. 14, 3/16", 7/32", 1/4", 9/32", 5/16", 11/32", 3/8", 7/16", 15/32", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16", 7/8", 15/16", 1", M2, M4, M4.5, M5, M5.5, M6, M6.3, M7, M8, M9, M10, M11, M12, M12.5, M14, M16, M18, M19, M20, M22, M24, M25	Steel	Plastic Case	3, 4	000000

Taps

Cut threads into holes so screws, bolts, and rods fit snugly. Our basic taps have straight flutes that are good for most jobs.

High-Speed Steel—The most versatile taps resist heat and wear to stay sharp. They’re good for most metals and plastic.

Uncoated—The economical choice, these won't last as long as coated taps.

Taper Chamfer—Good for both starting holes and threading through holes. These taps have the longest taper to gradually engage with the material, reducing the force needed to turn them. They can't reach the bottom of blind holes, however, so you will likely need to finish with a bottoming-chamfer tap.

Plug Chamfer—Our go-to chamfer type, these thread both through holes and blind holes. The tapered section is shorter than a taper chamfer and longer than bottoming chamfer. As a result, they're easier to turn than bottoming taps but require more force than taper taps.

Bottoming Chamfer—Cut all the way to the bottom of blind holes with taps that have the shortest taper. Since these require the most force to turn, they’re often used to finish holes started by taper- or plug-chamfer taps.

Number of Flutes—Taps with fewer flutes have more space to capture chips, so you won’t have to clear them as often. However, they can be more difficult to keep straight in the hole.

Taps Sold as Sets—Include one tap of each chamfer type.

	Taps														Taps Sold as Sets
						Drill Bit			Taper Chamfer		Plug Chamfer		Bottoming Chamfer
	Thread Size	Thread Lg.	Overall Lg.	Thread Type	No. of Flutes	Size, mm	Decimal Size Equiv.	Shank Type		Each		Each		Each	No. of Taps		Each
High-Speed Steel







				Uncoated

				M9 × 1 mm	1 1/4"	2 15/16"	Metric	4	8	0.315"	Square	000000000	000000	000000000	000000	000000000	000000	3	000000000	000000


				M9 × 1.25 mm	1 1/4"	2 15/16"	Metric	4	7.7	0.3031"	Square	000000000	00000	000000000	00000	000000000	00000	3	000000000	000000

Chip-Clearing Taps

Spiral Flute for Blind Holes

Remove long, stringy chips to produce cleaner threads than standard taps. The flute design prevents buildup to protect the quality of the threads and avoid damage to the tap. Since you don’t need to reverse these taps to extract chips, they also create threads faster.

High-Speed Steel—The most versatile taps resist heat and wear to stay sharp. They’re good for most metals and plastic.

Titanium Carbon Nitride (TiCN) Coated—Resist heat, chipping, and wear for three times the life of uncoated taps.

Spiral Flute for Blind Holes—Pull chips back toward the tap so they won't build up in blind holes. When tapping brittle material like iron that creates fine or powdery debris, choose a straight-flute tap.

Bottoming Chamfer—These taps have the shortest taper to thread close to the bottom of blind holes. They require the most force to turn, so they’re often used to finish holes started by plug-chamfer taps.

					Drill Bit			Spiral Flute for Blind Holes
	Thread Size	Thread Lg.	Overall Lg.	Thread Type	Size, mm	Decimal Size Equiv.	Shank Type	Chamfer Type	No. of Flutes		Each
High-Speed Steel







				Titanium Carbon Nitride (TiCN) Coated

				M9 × 1.25 mm	25/64"	3 17/32"	Metric	7.9	0.313"	Square	Bottoming	3	00000000	000000

Tap Extractors for Screw Thread Taps

Fingers on the extractor grip the flutes on a broken tap. Use with a tap wrench to remove taps with straight flutes from the workpiece without damaging the surrounding threads.

Tap Extractors						Replacement Tap Extractor Fingers
For Tap Size	Material	Square Shank Size	Choose a Number of Tap Flutes		Each	Choose a Number of Tap Flutes	Pkg. Qty.		Pkg.
3/8", M9, M10	Steel	0.223"	2 , 3 , 4	00000000	000000	2 , 3 , 4	12	00000000	000000