Connect to Fluke multimeters with a set of red and black test leads.

These kits include a set of red and black Fluke test leads with a variety of interchangeable tips.

Choose your own combination of test lead tips and cords.

Measure current without interrupting the circuit by connecting these test leads to a multimeter or current meter.

Perform electrical tests with a set of red and black test leads and interchangeable tips.

Hook up electrical testing equipment and create test circuits.

Convert a test lead tip style to take a new electrical measurement without switching test leads.

Also known as a geophone clip, this clip has rounded jaws that clamp onto battery terminal lugs and other curved surfaces for hands-free testing.

Create an automated system to test continuity in circuit boards. Combine these spring-loaded test probes with Spring Test Probe Sockets that are permanently attached to testing fixtures.

Determine how much current a device with a two- or three-wire power cord uses without pulling apart the wires. The splitter isolates hot and neutral wires so you can measure AC current in either wire with a clamp-on multimeter.

With this combination loop calibrator and multimeter, check for current control loop issues in PLCs, motors, and fans in addition to taking other electrical measurements. When used as a loop calibrator, the current input as well as the percentage of the input scale is shown on the dual display, giving you quick diagnostic information. Fluke is known for quality and durability.

Record measurements from electrical tests over time to identify intermittent issues such as voltage spikes and temporary power flow problems. Review data captured by these high-quality and durable Fluke multimeters in real-time or save it for future analysis.

More precise than test strips, this meter is often used to measure the pH of dirty liquids in agricultural systems, aquaculture tanks, and printing fountains.

Transmit pH readings to a PC for analysis. These meters have a sensor on a 6-ft. cable for taking remote readings of water and other clean liquids.

Since this oxidation reduction potential (ORP) meter has a housing that meets IP67 for complete resistance to dust and protection from temporary submersion, it’s often used to determine a solution’s ability to break down contaminants in harsh field conditions.

Check the oxygen levels of water and other clean liquids in harsh field conditions. This meter has a housing that meets IP67 for complete resistance to dust and protection from temporary submersion.

Pour contaminated water, wastewater, printing fountain solutions, and other dirty liquids into the meter cup to test electrical conductivity levels that indicate the concentration of salts, nutrients, chemicals, and other substances.

Commonly used to test environmental samples, boiler condensate, wastewater, and other dirty liquids for contaminants, this bench-top meter determines the total dissolved solids (TDS) in a solution.

Don’t strain your eyes reading a scale—these bench-top meters indicate exact results on the digital display.

Thick wire with ceramic insulation stands up to extreme air temperatures in forging, die casting, and heat treating.

An armored stainless steel cable protects wiring from corrosion and damage in humid conditions and harsh environments.

Send temperature readings from tanks, containers, and pipes to devices such as remote displays and programmable logic controllers (PLCs) without the need for a separate thermocouple transmitter.

Remotely monitor the temperature of liquids and gases in hard-to-access, hot, and high-vibration areas.

Trim these probes to the exact length you need with a pipe cutter.

The armored stainless steel cable resists wear, abrasion, and corrosion in humid and harsh conditions.

Bend these probes up to 90° for a custom fit.

Protect thermocouple wiring from wear and corrosion with an armored stainless steel cable.

To withstand harsh environments, a protective head seals out dust and moisture and thick probe walls reduce wear on the sensing element.

The probe tips come attached to mounting connections for fast installation.

For fast installation, the tips of these RTD probes come attached to mounting connections.

A built-in transmitter converts the probe’s air-temperature readings to a 4-20 mA signal for use with switches, controllers, and data loggers.

Measure and store temperature readings and upload the data to a PC.

Remotely check temperature on the go. These thermometers have a magnetic-back display for temporary mounting and a thermocouple probe with a 5-ft. coiled cable.

Store up to 500 readings on these thermometers and determine temperature within ±0.75° F accuracy.