Cut left-hand external threads on bolts, studs, and rods.

Use these dies with Ridgid pipe and conduit threader die heads on Ridgid pipe and conduit threaders.

Use these dies with Ridgid pipe and conduit threader die heads on Ridgid pipe and conduit threaders.

Grip compatible die heads to cut external pipe and conduit threads by hand.

Create external pipe and conduit threads.

A smaller width than standard hex dies lets you repair threads in tight spaces.

Clamp these dies around your workpiece, so you can start thread repair anywhere along the length of a bolt, stud, or rod. They're hex shaped for use with conventional wrenches.

Renew rusted and damaged pipe and conduit threads.

Clean and restore the fine threads on power transmission shafts that are used with bearing locknuts. Dies are sized according to the American Bearing Manufacturer's Association (ABMA).

Tap threads for left-hand threaded fasteners.

Sized to cut oversized threads, these tools are often used to tap holes where the threads will shrink due to heat treatment or plating.

Keep chips clear while tapping. Also known as gun taps, these have spiral-point flutes that push chips ahead of the tap and out of through holes.

Create oversized threads while keeping chips clear. These taps are sized for use in holes where the threads will shrink due to heat treatment or plating.

The spiral flute design pulls chips back toward the tap, so chips won't accumulate in closed-end holes.

With a drill bit point to drive into the workpiece, these taps can drill and tap holes in a single step. A 1/4" hex shank connects them directly to tools such as drills and power screwdrivers.

A high helix angle provides the cutting strength needed to tap threads in titanium. These cobalt steel taps have an open flute design that keeps chips clear, so they don't need to be reversed to prevent buildup.

To tap nickel and other hard material, these cobalt steel taps have high cutting strength. Their flutes are designed to keep chips clear, so they don't need to be reversed to prevent buildup.

Tap threads into hardened steel and iron. These cobalt steel taps have straight flutes for high durability.

With an extra-long shank, these taps have extended reach for tapping deep and hard-to-reach areas in pipe and conduit.

Use these carbon steel taps for thread repair and occasional tapping of pipe and conduit. They can tap threads into most metal and plastic, but they have a shorter tool life than standard taps.

Drill and thread holes for pipe and conduit without switching tools.

Made of cobalt steel, these taps are for use on hard pipe and conduit material, such as hardened steel.

The cutting teeth are shaped to cut smooth threads in soft pipe and conduit material.

Connect these extensions to your tap for greater access to hard-to-reach areas. Sets include nine extensions to fit different tap sizes.

For start-to-finish tapping of left-hand threads, these sets include one taper-, one plug-, and one bottoming-chamfer tap.

Create pipe and conduit threads in a range of hole diameters.

Drill and tap a variety of hole sizes. These taps and drill bits are for use on metal and plastic.

Also known as gun taps, the taps in these sets have spiral-point flutes that push chips ahead of the tap and out of through holes.

Cut and repair threads and drill holes in many different sizes. Tap and die wrenches are included.

Switch from internal to external threading with interchangeable tap and die adapters. Use them with the included ratcheting wrench.

Renew external threads in a wide range of sizes. The dies in these sets have a narrower width than standard dies, making them a good choice for thread repair in tight spots.

Cut several sizes of external screw threads.

Made from 410 stainless steel, these screws are strong, wear resistant, and mildly chemical resistant.

Made from 410 stainless steel, these screws are strong, wear resistant, and mildly chemical resistant.

Made from 410 stainless steel, these screws are strong, wear resistant, and mildly chemical resistant.

A wide cutting slot provides excellent chip clearing and low driving torque in soft metal.

Commonly used with door hinge hardware, these screws cut threads in material such as aluminum and brass.

These 18-8 stainless steel screws have a hardened steel drill point to penetrate steel and are coated to increase corrosion resistance.

These steel screws have corrosion-resistant finishes.

Made from stainless steel, these screws are more corrosion resistant than steel, and almost as strong.

These steel screws save you time and effort by drilling their own holes and fastening in a single operation.

A tamper-resistant Torx driver is required for installation and removal. Also known as pin-in-Torx, these screws allow you to apply extra force with less slippage or damage to the recess.

Also known as pancake head screws, these have a head that is about two-thirds the height of standard rounded head screws.

By drilling their own holes and fastening in a single operation, these square-drive screws save time and effort. Made of 410 stainless steel, they're both stronger and more wear resistant than 18-8 stainless steel screws.

Stronger and more wear resistant than 18-8 stainless steel, these screws are mildly chemical resistant.

Drill a pilot hole, cut threads, and fasten in one motion with these metric-threaded screws. Made of steel, they’re strong and wear resistant.

Made from 18-8 stainless steel, these screws have good chemical resistance.

One-third the weight of steel, aluminum screws resist corrosion in wet environments.

Beveled under the head for use in countersunk holes.

These steel screws are available with corrosion resistant finishes. A rubber-bonded washer compresses to form a watertight seal. They save you time and effort by drilling their own holes and fastening in a single operation.

Made from 410 stainless steel, these screws are strong, wear resistant, and mildly chemical resistant.

A point centers the screw in a starter hole and widely spaced threads reduce the risk of cracking plastic.

These screws speed installation by drilling, tapping, and fastening wood and metal in a single operation.

18-8 stainless steel screws have good chemical resistance.

More corrosion resistant than 18-8 stainless steel screws, these have excellent resistance to chemicals and salt water.

A drill point powers through metal up to 0.105" thick.

Power through drywall and into metal studs up to 0.105" thick.

Also known as plumber's lard oil, these light-colored lubricants are chlorine and sulfur free, so they won't stain soft metal, such as aluminum or copper. They reduce friction between your cutting tool and workpiece to make cutting cycles faster and easier.

Reduce mess and waste with these easy-to-apply, nonstaining lubricants. They reduce friction between your cutting tool and workpiece to make cutting cycles faster and easier, improve surface finishes, and extend tool life. All resist running and dripping.

These easy-to-apply stick lubricants won't drip or run for a cleaner workspace. Use them for tapping many types of metal, as well as plastic and rubber. Apply to taps to make cutting faster and easier, improve surface finishes, and extend tool life.

Formulated for use on soft metal, such as aluminum, copper, and brass, these lubricants won’t stain. They reduce friction between your cutting tool and workpiece to make cutting cycles faster and easier, improve surface finishes, and extend tool life.