Comparable to Grade 8 steel, these threaded rods have a tensile strength of 150,000 psi, making them about 25% stronger than medium-strength steel rods.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

About half the strength of medium-strength steel threaded rods, use these for light duty hanging, mounting, and fastening.

18-8 stainless steel threaded rods have good chemical resistance.

Grade B8 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges. They have good chemical resistance.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

These hardened 316 stainless steel threaded rods are 40% stronger than standard Grade B8M threaded rods. They meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

Made from nylon 6/6, these threaded rods resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.

Unlike metal rods, these threaded rods will not warp at extreme temperatures, making them ideal for heat treating and furnace fixtures.

These acetal threaded rods won't absorb moisture like nylon and fiberglass rods, so they're good for use in wet environments. They resist alcohol, gasoline, and solvents.

One-third the weight of steel, aluminum threaded rods resist corrosion in wet environments.

Bronze threaded rods are stronger and more resistant to salt water than brass rods.

Commonly used in valves, pumps, and shafts, these 400 nickel threaded rods resist salt water and caustic chemicals.

A hex drive on one end allows these rods to be turned with a hex key for ease of installation.

18-8 stainless steel studs have good chemical resistance and may be mildly magnetic. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.

Pass these studs through a hole and weld them in place.

Connect and separate threaded rods, studs, and other components. These hollow rods have internal threads on both ends, so you can make connections and still pass wiring and other objects through the center of the rod.

About half the strength of medium-strength steel coupling nuts, these nuts are for light duty fastening applications.

Made from Grade 5 steel, these inch-sized coupling nuts are suitable for most applications.

Comparable in strength to Grade 9 bolts, these coupling nuts are about 20% stronger than high-strength steel coupling nuts. Available in inch thread sizes.

More corrosion resistant than 18-8 stainless steel coupling nuts, these nuts have excellent resistance to chemicals and salt water.

Brass coupling nuts are corrosion resistant in wet environments and electrically conductive.

Known for their strength, steel coupling nuts are available with a corrosion-resistant finish.

Connect two differently sized male-threaded parts, such as threaded rods, and tighten with a standard wrench.

Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.

Mount these two-piece collars anywhere on an Acme lead screw without removing components.

Designed for use with right-hand, externally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.

Clip retaining rings into the grooves to separate and position collars, supports, and housings.

Connect these internally threaded shafts directly to threaded components, or use a fastener to secure.

A flat surface area allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings.

Combine with a machine key to transmit torque to gears, sprockets, and other power transmission components.

Secure setup clamps and fixtures to your machine table, or assemble heavy machines, such as engine mounts.