Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.

A shoulder near the end of the shaft allows for easy positioning of housings, shaft supports, and collars.

Attach threaded accessories, such as mixer propellers and fan blades, to the end of these shafts.

Mount the flange to a machine or wall to support idler sprockets and pulleys in tensioning applications. They include washers and a nut to position your component and hold it in place.

A flat surface area allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings.

Combine with a machine key to transmit torque to gears, sprockets, and other power transmission components.

Comparable to Grade 8 steel, these threaded rods have a tensile strength of 150,000 psi, making them about 25% stronger than medium-strength steel rods.

Class 12.9 rods are about 20% stronger than Class 10.9 threaded rods and are for use in heavy machinery.

About half the strength of medium-strength steel threaded rods, use these for light duty hanging, mounting, and fastening.

These metric threaded rods tighten when turned to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.

These Grade B7 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

These metric Grade B7 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

An economical alternative to Grade B7 and Grade B16 threaded rods, these metric Class 8.8 rods are suitable for fastening most machinery and equipment.

18-8 stainless steel threaded rods have good chemical resistance.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

Stronger and more wear resistant than 18-8 stainless steel, these threaded rods are mildly chemical resistant. They meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

These metric 316 stainless steel threaded rods are more corrosion resistant than 18-8 and 410 stainless steel threaded rods and have excellent resistance to chemicals and salt water.

Grade B8M threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

The most corrosion resistant stainless steel threaded rods we offer, these Alloy 20 stainless steel threaded rods contain nickel to withstand exposure to sulfuric, phosphoric, and nitric acids.

These metric threaded rods are made from nylon 6/6 and resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.

Unlike metal rods, these metric threaded rods will not warp at extreme temperatures, making them ideal for heat treating and furnace fixtures.

Fiberglass threaded rods are stronger than nylon threaded rods. They resist acids, solvents, salt water, and oil.

PTFE threaded rods withstand temperatures up to 250° F and resist oil, grease, detergents, and most mineral acids. They're the lowest friction plastic threaded rods we offer, so they thread on smoothly.

Brass threaded rods are corrosion resistant in wet environments, electrically conductive, and nonmagnetic.

Titanium threaded rods have a high strength-to-weight ratio and are resistant to acids and salt water.

Commonly used in valves, pumps, and shafts, these 400 nickel threaded rods resist salt water and caustic chemicals.

A hex drive on one end allows these rods to be turned with a hex key for ease of installation.

Screw the threaded end of these metric studs into a tapped hole and use the unthreaded end as a pivot point, hinge, shaft, or locator pin.

Connect and separate threaded rods, studs, and other components. These hollow rods have internal threads on both ends, so you can make connections and still pass wiring and other objects through the center of the rod.

These studs have good chemical resistance. Weld them to stainless steel surfaces.

These metric 316 stainless steel studs have excellent resistance to chemicals and salt water. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.

These studs are also known as hanger bolts—use them to hang, mount, and fasten parts to wood structures.

A hollow center allows these studs to be used as an axle, a vent, or a passageway for wiring.

These steel studs are zinc plated to resist corrosion in wet environments.

These steel studs are zinc plated to resist corrosion in wet environments.

Designed for use with right-hand, internally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension. Add right- and left-hand threaded rod ends to build your linkages.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.

Combine with an externally threaded acme nut to create a custom flange nut.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Found in hand-powered clamps, vises, grates, doors, and work tables, lead screws and nuts have broad, square threads that are well suited for quick assembly, high clamping forces, and lifting and lowering heavy objects.

Thread these one-piece collars onto an Acme lead screw.

Install these threaded collars on a metric lead screw to separate and position components, or use them as an end stop to limit travel.

Keep your ball screw spinning without the ball nut damaging your system. When the ball nut reaches the stop pin at either end of the ball screw, it disengages and begins to idle.

Also known as single-start ball screws and nuts, these have a single thread that runs the length of the screw. They operate with more torque than fast-travel ball screws and nuts.

Internal ball bearings provide smooth low-friction travel in applications that require high speeds, accurate positioning, and repeatable movement. Also known as single-start metric ball screws and nuts, these have a single thread that runs the length of the screw.

A set of ball bearings reduces friction and secures the end of a ball or lead screw.

Secure setup clamps and fixtures to your machine table, or assemble heavy machines, such as engine mounts.