Made of 18-8 stainless steel, these inserts have better corrosion resistance than black-phosphate steel.

These inserts are the most corrosion-resistant thread-locking inserts we offer.

These assortments include various sizes of thread-locking inserts.

Made of Nitronic 60 stainless steel, these inserts prevent the screw from binding or sticking without any coating or lubricant that could contaminate particle-free environments.

These inserts have a high strength-to-weight ratio and resist acids and salt water better than nickel alloy and stainless steel inserts.

A distorted thread grips the screw to resist loosening.

A dry film keeps the screw from sticking or binding in these inserts during installation.

Assortments include various sizes of helical inserts and a tap, a drill bit, and an installation tool for each thread size.

A dry film keeps the screw from sticking or binding in these inserts during installation.

These kits have short-, normal-, and long-reach inserts, an installation tool, and a tap.

A black-phosphate finish provides mild corrosion resistance.

The strongest key-locking inserts we offer, these inserts are made to stringent military specifications.

These inserts come with an installation tool. Drive the keys into the surrounding material for a more secure hold than thread-locking inserts.

Made from brass, these inserts are nonmagnetic, corrosion resistant, and electrically conductive.

These aluminum inserts are 70% lighter than brass inserts, electrically conductive, and nonmagnetic. They have good corrosion resistance, which is comparable to brass but not as good as stainless steel.

These 18-8 stainless steel inserts have better corrosion resistance than brass inserts and may be mildly magnetic.

The flange keeps these inserts from pulling through a hole. Press them in from the underside of material, and install a screw from the top of material.

Use these inserts to install fine-thread screws in existing holes.

These 18-8 stainless steel inserts have better corrosion resistance than aluminum inserts and may be mildly magnetic.

Install these inserts into plastic parts to create a secure base for fasteners.

The tapered shape makes it easier to guide these inserts into a hole during installation. Use a drill bit to create a straight hole, then taper the top half.

The flange keeps these inserts from being pulled through a hole and provides a load bearing surface.

Assortments include various sizes of tapping inserts for softwood.

Steel inserts have high strength for durability.

Steel inserts have high strength for durability.

The most corrosion resistant tee nut inserts we offer, these inserts stand up to chemicals and salt water.

Ridges on the barrel of these inserts make them less likely to split hardwood than inserts with prongs. They're often used in wood that has been cut across the growth rings.

Use where vibration is a concern—these tee nut inserts have distorted threads that lock screws in place.

Knurls hold these inserts in hardwoods such as oak, maple, and walnut to prevent twisting.

An open end allows long screws and bolts to pass through the insert.

Press these inserts into a drilled hole and the flexible metal teeth anchor them in the material. Use them with carbon fiber, fiberglass, and garolite.

Choose these standoffs for their adherence to NAS 1831 specifications.

These standoffs are made to NAS specifications.

Mount components onto food processing lines, walls, and sanitary equipment while leaving space to clean in between.

These standoffs are designed to fit in the limited space of compact electronics such as laptops and hand-held devices.

Use these barrels with a screw you already have or pair with a different type of screw to create a custom fastener. Made from 316 stainless steel, they have excellent chemical resistance and can be used in saltwater environments.

Use these barrels with a screw you already have or pair with a different type of screw to create a custom fastener. Made from 18-8 stainless steel, they are chemical resistant.

Use these barrels with a screw you already have or pair with a different type of screw to create a custom fastener. They're zinc plated to resist corrosion in wet environments.

Use these hex drive screws and binding barrels as a low-profile alternative to standard nut and bolt combinations.

Stainless steel binding barrels and screws have excellent corrosion resistance in most environments.

Brass binding barrels and screws are corrosion resistant in wet environments and electrically conductive.

An unthreaded barrel allows quick assembly with a press or a hammer.

Plastic binding barrels and caps are chemical resistant, nonconductive, and lightweight.

Brass binding barrels and screws are corrosion resistant in wet environments and electrically conductive.

More corrosion resistant than 18-8 stainless steel binding barrels and screws, these have excellent resistance to chemicals and salt water.

Sealed with PVC foam under the head to prevent leaks and keep contaminants out.

Connect two differently sized male-threaded parts, such as threaded rods, and tighten with a standard wrench.

Increase or decrease metric thread size from one male-threaded part to another. Commonly used to connect two differently sized threaded rods, they have a hex-shaped body, so you can tighten them with a standard wrench.

Connect male- and female-threaded parts of different thread types and sizes, while allowing air, liquids, wire, or other thin materials to pass through.

Change inch threads to metric with these adapters, or swap metric threads for inch. An external hex lets you tighten or loosen them with a wrench.

In addition to joining male- and female-threaded parts, these adapters can increase or decrease metric thread sizes and change the thread pitch.

These 18-8 stainless steel anchors have good chemical resistance.

A zinc plating provides corrosion resistance in wet environments.

A zinc plating provides corrosion resistance in wet environments.

Install like a stud anchor—just thread the anchor, a nut, and a washer onto the end of a threaded rod, drive into a hole, and turn the nut to expand the base. Also known as rod anchors, they're often used with threaded rod to hang pipe and wiring.

Also known as caulk-in anchors, these stay secure when there's not much material to hold.

Drive these tools with a hammer to expand anchors.

Also known as double expansion anchors, these expand from both sides for full contact and a secure hold.

A pivoting toggle bar creates a strong hold.

Stronger than stainless steel, these nuts are comparable in strength to Grade 9 bolts.

About twice as strong as aluminum rivet nuts, these steel rivet nuts are zinc plated for mild corrosion resistance.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

Wedges under the flange lock the nut in place in soft materials such as brass and aluminum.

These aluminum rivet nuts are one-third the weight of steel rivet nuts and have mild corrosion resistance.

A PVC coating minimizes the chance of scratching the surface of your material. These rivet nuts are more corrosion resistant than zinc-plated steel rivet nuts.

These rivet nuts are mildly corrosion resistant.

A nonconductive rubber coating insulates the nut from electricity, seals out moisture, and damps vibration.

About twice as strong as aluminum rivet nuts, these low-profile rivet nuts have a cadmium or tin-zinc plating for corrosion resistance.

Threads float inside the nut so you can install a screw at a slight angle to align with off-center parts. They’re also known as Riv-Float nuts.

These low-profile rivet nuts are one-third the weight of steel and have mild corrosion resistance.

These screw-mount nuts are often used to attach glides and levels to wood.

These nylon nuts are chemical resistant, nonconductive, and lightweight.

Use these rivet nuts for light duty fastening in low-clearance applications. Assortments include rivet nuts, mandrels, and an installation tool.