These brass fittings have the strength to handle high-pressure applications.

The plating on these brass fittings creates a shiny finish and provides extra protection in corrosive environments. Fittings have the strength to handle high-pressure applications.

Use these fittings in low-pressure flow applications. They have good corrosion resistance.

Use these fittings in extreme-pressure conditions up to 15,000 psi.

The strongest steel fittings we offer, these can withstand extreme-pressure applications.

The galvanized finish on these fittings provides fair corrosion resistance. Fittings are for use in low-pressure applications.

Connect these fittings to thick-wall plastic pipe—they have thicker, stronger walls than standard-wall fittings, so they can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They can withstand pressures up to 900 psi.

Connect to CPVC pipe for use in high-temperature plumbing and water supply applications up to 200° F.

Extreme temperatures are no problem for these fittings—they’re made of PTFE, so they can withstand a wider temperature range than any of our other plastic pipe fittings for chemicals. They are commonly used in high-purity chemical flow processes, such as semiconductor and clean room applications.

Made of brass, these fittings have good corrosion resistance.

A 316 stainless steel body gives these fittings the best corrosion resistance of all our metal push-to-connect tube fittings.

Use at pressures up to 250 psi.

An all-metal body and built-in tube support or dual seals allow these fittings to handle the highest pressure ratings of all our push-to-connect tube fittings.

Minimize leaks in your line—these fittings have a single barb that creates a smooth clamping surface for extra-tight connections.

Fittings have good corrosion resistance.

Lighter in weight than metal quick-disconnect couplings, these couplings are plastic.

With no latch, these couplings have a compact design to fit in small spaces. They can handle pressures up to 700 psi.

Lighter in weight than their metal counterparts, these compression fittings are polypropylene.

A single sleeve (ferrule) compresses the tubing as you tighten the nut on these fittings, creating a strong seal. They are brass for good corrosion resistance.

Fittings can withstand temperatures up to 200° F.

These plastic compression fittings meet NSF/ANSI Standard 51 for food contact.

Also known as instant fittings, these chemical-resistant plastic fittings connect to tubing with a push, and an internal gripping ring and fluoroelastomer O-ring hold the tubing tight.

Quick-disconnect couplings consist of a plug and a socket that join with a latch so you can easily connect and disconnect your line. Use in applications up to 120 psi.

Use these fittings at pressures up to 9,700 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on stainless steel tubing that is flared to 37°.

A PTFE seal on the tube end of these fittings allows for an extra-strong connection in high-vibration applications.

Transfer liquids and gasses into high-vacuum chambers with these assembled fittings, also known as feedthroughs.

These fittings have two sleeves for extra gripping power. They bite into steel tubing as you tighten the nut to form a strong seal.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal.

These grips are sized to fit in tight areas.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.

These 90° elbows absorb less water and are less likely to crack or corrode than other types of plastics and metals.

Extend your cord’s life while stopping it from coming loose in places that are sanitized with water or steam as hot as 300° F, such as food plants and clean rooms.

Push to install these cord grips in wet environments and high-movement applications such as robotics and handheld equipment.

Vent air from your enclosure to equalize pressure and stop condensation from forming inside while securing cords in wet environments. These polyamide grips are lightweight and resist rusting.

Tighten the screw-down clamp for superior pull-out resistance.

Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.

Lighter in weight than steel and brass grips, these aluminum grips are strong enough to secure cords in demanding wet environments.

Create a tight grip on cords in wet environments while reducing stress from bending—the 90° angle of these cord grips routes cords to fit tight spaces in enclosures and panels.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

Keep cords from coming loose and seal water out of enclosures in extremely cold labs and storage areas. Thanks to their plastic bushing and rubber O-ring, these grips withstand temperatures as low as -75° F.

These grips have an extension that provides extra support for moving cable and prevents kinking for longer cable life.

Built with snap-in tabs and a spring extension, these cord grips install into panel holes more quickly than standard grips and better prevent damage from sharp bends.

Made of nylon, these grips resist chemicals.

The mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

These cord grips are lightweight yet durable.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Secure and seal electrical cords entering knockouts at a 45° angle.

An insert clamps the cable in place to provide more strain relief than other snap-in cord grips for building cable.

These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These stainless steel grips offer the most protection from wet, corrosive environments of any of our metal wet-location cord grips. They are rated IP67 for protection from temporary water submersion.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.