These slotted thumb screws have a thin, knurled head for use in low-clearance applications. Made of 18-8 stainless steel, they are chemical resistant.

These metric thumb screws have a thin, knurled head for use in low-clearance applications. They have a black-oxide finish to resist corrosion in dry environments.

Brass thumb screws are corrosion resistant in wet environments and electrically conductive.

These metric thumb screws are made of chemical-resistant 18-8 stainless steel. They have a raised head that makes them easy to grip.

These metric thumb screws have a raised head that makes them easy to grip. A black-oxide finish provides corrosion resistance in dry environments.

Use these slim thumb screws in tight spaces.

Stainless steel thumb screws have excellent corrosion resistance in most environments.

With a slim profile, these metric thumb screws fit in tight spaces.

These steel thumb screws have a black-oxide finish to resist corrosion in dry environments.

Fasten material by hand, so tools don’t scratch or contaminate parts you frequently adjust in food-processing or pharmaceutical plants.

Stainless steel thumb screws have excellent corrosion resistance in most environments.

A large head allows you to grip these screws with your entire hand for greater torque while tightening than standard knurled plastic-head thumb screws.

These metric thumb screws have a knurled head for a slip-resistant controlled adjustment.

Arms provide a flat surface to push your fingers against.

These metric thumb screws have wings that provide more leverage than spade-head thumb screws for greater torque while tightening. A zinc plating provides corrosion resistance in wet environments.

These metric thumb screws have arms that provide a flat surface to push your fingers against.

These metric thumb screws are made of chemical-resistant 18-8 stainless steel. Also known as dog- and pilot-point thumb screws, insert the point into a drilled hole or slot to hold items in place.

A wide tip provides more gripping power than standard swivel-tip thumb screws. To use, remove the tip, thread the screw through the hole, and attach the tip on the other side.

For maximum contact with angled and uneven surfaces, the tip swivels in all directions. The tip is narrow so it will fit through threaded holes.

A raised head makes these thumb screws easy to grip. Made from nylon, they're chemical resistant, nonconductive, and lightweight.

These nylon thumb screws are chemical resistant, nonconductive, and lightweight.

These steel thumb screws have a black-oxide finish to resist corrosion in dry environments.

Install these rounded head screws through a hole and thread on a retainer to keep secure—no special tools are required.

These rounded head nuts can be riveted into thin panels for a flush fit. They can be mounted without spaces between the panels. A quarter-turn locks and releases access panels, doors, and covers.

Press these wing head nuts into the backside of a panel in applications where you have access to both sides of the panel. A quarter-turn locks and releases access panels, doors, and covers.

These rounded head screws have a nut that clips onto the edge of a thin panel, allowing you to mount the screw near edges. A quarter-turn locks and releases access panels, doors, and covers.

Press these wing head nuts into a closed-end hole or thick panel in applications where the back of the panel is inaccessible. A quarter-turn locks and releases access panels, doors, and covers.

Snap these screws into panels up to 0.125" thick—no tools are required for installation.

These screws mount flush against the outer panel's surface for low-clearance applications.

The base flares out during installation, creating a backside flange in hard materials and near edges in panels up to 0.312" thick. Install with a flare-in installation tool and an arbor press.

Install and remove these shoulder screws by hand or with a hex key.

For metric thread sizes with excellent resistance to chemicals and salt water, choose these 316 stainless steel shoulder screws.

A rubber coating provides a comfortable grip to position, tighten, and hold fixtures, equipment, and machinery. Mount these knobs into a threaded hole.

The domed top allows you to firmly hold these knobs in the palm of your hand to position, tighten, and hold fixtures, equipment, and machinery. Mount them into a threaded hole.

Suitable for food-processing areas, these one-piece knobs have no joints to collect dirt or debris. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery. Mount them into a threaded hole.

Never lose these knobs—tether them to equipment to keep them where you need them. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery. Mount them into a threaded hole.

A rubber coating provides a comfortable grip to position, tighten, and hold fixtures, equipment, and machinery. Install these knobs on a threaded stud.

Identify equipment controls and components at a glance by their color. Install these knobs on a threaded stud. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Keep a convenient selection of knobs on hand. To build a custom knob or thumb screw, pair one of these knobs with a socket head screw. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Use these knobs to display important messages. To build a custom knob or thumb screw, pair one of these knobs with a socket head screw. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

To build a custom precise-control knob or thumb screw, pair one of these knobs with a socket head screw. Turn the knob to move the screw 0.005" per graduation and make precise adjustments.