Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension. Add right- and left-hand threaded rod ends to build your linkages.

Designed for use with right-hand, internally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Also known as rod‐end bearings, ball joint rod ends have an eyelet and a ball that swivels to support angular misalignment.

A carbon fiber-reinforced insert or PTFE liner reduces wear, handles shock loads, and eliminates the need for lubrication.

Connect your grease gun to the fitting to lubricate. Internal threads mate with rod end bolts, threaded rods, and other components with male threads.

For ease of installation, these rod ends come with a compatible jam nut. They have an eyelet and a ball that swivel to support angular misalignment.

An oil-embedded bronze insert slowly releases lubricant throughout the life of these internally threaded rod ends.

An oil-embedded bronze insert slowly releases lubricant to the rod end. Connect your grease gun to the fitting to relubricate.

With at least 55° of ball swivel, these rod ends accommodate greater misalignment than any other internally threaded rod end we offer.

Made of cadmium-plated steel, these internally threaded rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends.

Made to extremely tight tolerances, these internally threaded rod ends are for applications that require positioning accuracy, such as accelerators and other types of control linkages.

Made of stainless steel, these internally threaded rod ends provide excellent corrosion resistance.

These anodized aluminum rod ends are lighter than stainless steel rod ends and have good corrosion resistance.

Made of impact-resistant nylon, these internally threaded rod ends withstand corrosion as well as fuels, lyes, and weak acids. They do not require lubrication and are 80% lighter than steel rod ends.

These externally threaded steel rod ends handle loads that are at least 25% higher than other comparably sized rod ends.

These internally threaded rod ends have an innovative body design that keeps the ball from being pushed out when supporting thrust loads.

Along with internal threads, these rod ends have a double row of precision ball bearings that allows high speeds and smooth operation.

Decrease the ID of your rod end to allow approximately 60° of misalignment.

These rod end bolts are good for wet and corrosive environments—for maximum mounting flexibility, cut the fully threaded shaft to whatever length you need.

These alloy steel rod end bolts have the highest tensile strength of any steel fully threaded rod end bolt we offer.

Also known as swing bolts and eyebolts, these internally threaded rod end bolts have no moving parts. They're designed to make pivoting or hinge movements in applications that don't need to compensate for misalignment.

These black-oxide steel rod end bolts are heat treated for added strength.

To reduce noise and vibration, these bolts have a rubber bushing—connect them to rods, pipes, tubes, and cable linkages that have female threading. They’re also known as isolated rod ends.

Good for general purpose applications where corrosion and high strength aren’t a concern, these rod end bolts are made of carbon steel.

These steel rod ends are machined to SAE standards.

In addition to offering superior chemical resistance, these lightweight, fiber-reinforced nylon rod ends also reduce noise and vibration.

Make quick adjustments to these rod ends by inserting and releasing the clevis pins without the need to bend them into place.

These linkages offer excellent wear resistance. They consist of internally threaded ball joint rod ends with a ball stud attached to simplify mounting.

Along with excellent wear resistance, these linkages have a grease fitting for easy lubrication. An internally threaded rod end connects to threaded rods, studs, and other parts with male threads.

An oil-embedded bronze insert slowly releases lubricant to the rod end.

A slippery PTFE liner reduces wear and eliminates the need for lubrication.

Made of stainless steel, these ball joint linkages offer more corrosion resistance than steel and zinc ball joint linkages.

Made of stainless steel, these ball joint linkages offer more corrosion resistance than steel ball joint linkages.

Use these linkages to create inline pivoting connections. They have internal threads on one end and external threads on the other.

Attach these nuts to rods, pipes, and tubes to make pivoting and hinge movements where misalignment is not a concern.