The grips on these cutters drain static from your application, preventing buildup from electrostatic discharge (ESD).

The specially designed internal spring provides constant, uniform tension for superior performance.

Tungsten carbide cutting edges are bonded to the jaws for long life.

These cutters are stainless steel, which provides excellent corrosion resistance.

The black finish prevents glare that can interfere with precision work under bright light and magnification.

Blades are high-speed steel so they stay sharp longer than steel blades, and they can be sharpened.

A double hinge provides high cutting force with low gripping pressure. These cutters are also known as aviation snips.

Prevent waste from flying up as you work. A double blade makes two cuts to create a 7/64"-wide step that peels back, leaving little distortion and smooth edges.

Blades are tapered to give you more control when cutting straight lines, tight curves, and circles, and they're serrated to prevent slipping. These cutters are also known as duckbill snips.

Also known as bulldog snips, these durable cutters have long handles and short blades for cutting heavy material in any direction.

Handles are angled to keep your hand away from the material as you cut straight lines and curves.

Cut up to 1" deep V-shaped notches in sheet metal.

Use to cut patterns in flat material with minimal material loss and less effort compared to manual cutters.

Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

Make straight, clean cuts in thick sheet metal.

This large-capacity cutter has a 25" blade for long, straight cuts.

Notch, cut, and pierce a variety of materials including metal, plastic, and vinyl.

Cut hard steel wire, nails, and small rivets close to the surface with the wide, flat jaws on these cutters.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Precisely position and flush-cut copper, gold, silver, and magnetic wire.

Made of beryllium copper that is FM approved, these cutters satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Cut thin, hard wire with these small cutters.

With a short-nosed jaw, these cutters force the material being cut deeper into the jaw for maximum leverage. The short jaw also allows you to cut one side of a chain link or padlock hasp without hitting the other side.

Blades are flat on one side for close-to-the-surface cuts.

Slice through bolts and chain with low effort.

The small size and spring-loaded jaw lets you make quick cuts with one hand.

Keep your hands in a comfortable position so you can apply more force for cutting.

Minimize material distortion while cutting steel and stainless steel wire rope.

These manually operated cutters make a clean cut with just a few pumps of the handle.

Use the lever to make one-handed cuts with minimal material distortion. Cutter mounts to a workbench for extra stability and ease of use for repeated cuts.

Use these one-handed cutters on small-diameter aluminum and copper power and communication cable.

Jaws ratchet to increase cutting pressure as you open and close the handles.

Push the button to cut aluminum and copper power and communication cable.

Jaws open automatically for ease of use.

The head slides out of the handle and locks in position.

Minimize hand fatigue with a lightweight handle and spring-action that automatically opens the blades for quick repeat cuts.

Blades are ceramic to stay sharp longer than metal blades.

These small scissors have narrow, sharp tips for fine cutting and trimming

Cut and strip wire in tight spaces with the compact tips on these scissors.

Insulated handles protect against shock from accidental contact with live electrical circuits. These scissors are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

After each cut, the jaws spring open to make continuous cutting easy.

Squeeze the handles and the jaws automatically adjust to fit a workpiece and lock in place.

Curved jaws grip bolt heads and nuts with rounded corners. These pliers lock in a vise-like grip and stay clamped in place, leaving your hands free.

Additional features, such as wire terminal crimpers and wire stripping holes, enable you to perform a variety of electrical wiring and installation work with a single tool.

With thinner tips than standard long-nose pliers, these tools fit into tight spaces.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Made of materials that are FM approved, these pliers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Pull stripped, rusted, and tamper-resistant screws out of hard-to-reach places.

Colorful plastic grips make these assorted pliers stand out, so they’re less likely to be misplaced.

Insulated grips protect against accidental contact with live electrical circuits. These assorted pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Lock the jaws in a vise-like grip around a workpiece and these assorted pliers stay clamped in place to leave your hands free.

Extra-long handles enable access to hard-to-reach areas. Also known as lineman’s and combination pliers, use these tools to pull, bend, and cut wire.

Additional features, such as wire terminal crimpers, enable you to perform a variety of electrical wiring and installation work with a single tool. Also known as lineman’s pliers, use them to pull, bend, and cut wire.

Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. Use them to pull, bend, and cut wire.

Choose a stainless steel tool for environments where moisture and other contaminants are present. These pliers resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool. Use them to pull, bend, and cut wire.

Secure a lanyard to the ring on the handle to prevent dropping your pliers when working at height. Use these tools to pull, bend, and cut wire.

The narrow jaws fit into tight spaces, and the slip joint allows you to switch between two different jaw opening sizes.

The grips drain static from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment.