Epoxies are the strongest and most weather- and chemical-resistant structural adhesives. They work especially well on metals.

Toughened adhesives are blended with rubber particles for better impact resistance than standard epoxies. They form flexible, resilient bonds.

To allow time to adjust and position parts, these epoxies remain workable for at least 90 minutes.

With excellent resistance to corrosive chemicals and salt water, these epoxies work in tough conditions.

Fasten hard-to-bond plastics, such as polypropylene and polyethylene, with these epoxies.

Bond most materials without the strong odor of other epoxy adhesives.

Toughened adhesives are blended with rubber particles for better impact resistance than standard acrylics. They form resilient bonds.

Acrylics bond to the widest range of materials, especially plastics, and require the least amount of surface preparation.

Urethane adhesives are the most flexible, so they bond dissimilar materials and damp vibration.

Also known as super glue, these adhesives bond quickly.

Mixed with rubber for better impact resistance than standard instant-bond adhesives, these adhesives form strong, resilient bonds.

Accommodate joint movement with these adhesives that remain pliable when cured.

These adhesives withstand temperatures of 390° F or more.

Make strong, instant bonds on a variety of materials—but not your skin.

Use these thick gels, also known as super glue, on vertical surfaces or to fill gaps between parts.

These thick gels fill gaps up to 0.2" wide—the largest of any of our instant-bond adhesives.

For faster bonding, these adhesives begin to harden in half the time of our other wicking instant-bond adhesives.

To invisibly bond transparent plastics, these adhesives won’t turn cloudy.

For flexible bonds that resist cracking, these adhesives stay pliable.

Moisture, humidity, and immersion in water won't degrade the bond of these adhesives.

Spray a thin, uniform coat of adhesive on one or both surfaces, air dry, and then bring together to form strong bonds.

Apply this glue like tape for a no-mess alternative to liquid adhesives, hot melts, and staples. Also known as adhesive transfer tape.

Use these glue rolls with 3M dispensing guns.

This general purpose glue tackles a variety of repairs.

Temporarily stabilize objects on flat surfaces with this clear, reusable adhesive.

This putty-like glue cures into a pliable rubber. Use it to repair seals and cracks, or mold it into hooks and bumpers.

Apply these adhesives on two surfaces, air dry, and then bring together to bond.

When heated, these glue sticks melt and quickly begin to harden. Use them to seal packaging and form other low- to medium-strength bonds.

Prevent threaded fasteners from loosening due to shock and vibration.

Use these threadlockers on fasteners that require occasional fine-tuning, such as set screws.

Secure threaded fasteners at temperature extremes—from -300° F to 2100° F.

These threadlockers develop usable strength within one hour. Because they harden quickly on most metals, they don't require a primer.

Paste threadlockers are easy to apply and won't drip, even from overhead fasteners.

This gel clings to fasteners to prevent drips.

Wrap this no-mess tape around threaded fasteners up to 30 days before installation.

Use these threadlockers for threaded fasteners that require occasional fine-tuning, such as set screws.

Improve instant-bond adhesive performance on hard-to-bond materials.

Fill gaps up to 0.01" to secure unthreaded cylindrical metal parts such as shafts, bearings, and press-fit assemblies.

Fill gaps up to 0.02" to secure worn unthreaded cylindrical metal parts such as shafts, bearings, and press-fit assemblies.

Mix these two-part surface fillers together to repair leaks and cracks as well as to rebuild rough spots in metal.

For use in processing equipment that carries small particles less than 1/16" in diameter, these ceramic-filled epoxies rebuild and repair surfaces exposed to abrasion from particles, such as dust collectors, fan blades, and fan housings.

Repair and rebuild metal surfaces that are exposed to heat. These surface fillers withstand temperatures over 450° F.

Stop leaks in metal tanks and equipment without draining the contents.

Stop leaks in metal tanks and equipment without draining the contents. Until a permanent repair can be made, rub these sticks into the leak to form a temporary seal.

These surface fillers can be used on vertical surfaces without sagging. They repair cracked, worn, and damaged surfaces.

Knead the epoxy-coated patch and resin together to make repairs to pipes, tanks, drums, and containers in the field.

Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater.

Made from silicone, these sealants are RTV (room-temperature vulcanizing).

Resistant to mold and mildew, these sealants are well suited to high-humidity environments.

These sealants include a material certificate with traceable lot number, test report, and product shelf life.

This sealant includes a material certificate with traceable lot number, test report, and product shelf life.

Clear enough to read through, these UV-resistant sealants allow optimal light transmission for use with solar cells and fiber optics.

These structural sealants combine the mechanical strength of an adhesive with excellent sealing properties and high flexibility.

These sealants are marine grade, so they stand up to water, corrosion from salt spray, mildew, and UV light.

Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Impervious to the swelling effects of oil, fuel, and solvents, use these high-strength sealants to assemble and repair fuel systems and tanks.

These non-sagging sealants will not drip while hardening on vertical and overhead surfaces.