We will reply to your message within an hour.
More
A rubber seal protects these switches from splashing water.
These switches meet MIL-S-3950.
Maximize the space in a panel—these switches are half the size of most toggle switches.
Built into a terminal block, these switches mount to DIN rail.
Able to withstand high currents, these switches are often used with motors and pumps.
Prevent accidental actuation—these toggle switches must be pulled up before they can switch a circuit.
Choose from a variety of messages and colored lenses to combine a rocker with a base and wiring socket for a complete switch.
Rated IP67 for protection from dust and temporary submersion.
Also known as high-inrush current switches, these switches can handle starting currents up to 10 times greater than their rating, such as when a motor starts.
Maximize space in a panel—these switches are smaller than most standard rocker switches.
Rated IP67, these switches are protected from temporary submersion.
These switches withstand temporary submersion.
Often used in large, open workspaces, these switches can be wired on opposite ends of the room to control lights on the same circuit. They're also known as three-way and four-way switches.
Control lights by transmitting a wireless signal from these switches to a control relay on your fixture.
Also known as three-way switches, these are often used in large, open workspaces and can be wired on opposite ends of the room to control lights on the same circuit.
Often used in large, open workspaces, these switches can be wired on opposite ends of the room to control the brightness of lights on the same circuit. They're also known as three-way switches.
Adjust the brightness of lights.
Rated NEMA 4X, these switches are protected from corrosion and washdowns.
Use these switches to turn motors on and off, or with lighting and electric heat circuits. They do not provide overload protection.
These switches are housed in a protective enclosure.
Use these switches where ignitable gas and dust may be present. They're rated Class I, Divisions 1 and 2, Groups C and D; and Class II, Divisions 1 and 2, Groups E, F, and G for hazardous locations.
These switches are rated NEMA 3R for protection from falling water and light splashing.
Assemble your own motor starter by combining a switch and a thermal overload element.
Create one action with these valves, such as extending a cylinder.
Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/2 valves.
In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/3 exhaust center valves.
Mount these breakers, also known as supplemental protectors, through panels downstream from a branch circuit breaker to protect a single piece of equipment.
Unlike breakers that trip thermally, these breakers have a hydraulic-magnetic trip mechanism, so they aren’t affected by changes in temperature.
Also known as supplemental protectors, these circuit breakers mount directly to DIN rail downstream from a branch circuit breaker to protect a single piece of equipment.
Mount these circuit breakers directly to DIN rail to protect equipment and wiring in an area of your facility from overloads and short circuits.
Add ground fault protection to a circuit to minimize the risk of electric shock to workers and equipment if there is a current leak.
Install these circuit breakers into Cutler-Hammer CH series breaker boxes.
Match these circuit breakers to Square D breaker boxes or panel boards of the same manufacturer series.
Use with Siemens EQ series breaker boxes.
Protect an area of a facility that has high-powered equipment using up to 600V AC or 750V DC and 600A of current.
Switch your device on and off without needing a separate switch. These connectors work with industry standard cords often found on power supplies, appliances, and other electronic devices.
Rated IP67, these connectors create a dust- and watertight seal where they fit into the housing of power supplies, appliances, and other electronic devices. Instead of hardwiring your devices, these connectors let you plug in a standard IEC power cord and turn the power on and off with a built-in switch.
With a built-in switch, these connectors run power to appliances, power supplies, and other electronic devices while also filtering damaging EMI (electromagnetic interference).
These boxes come ready to use with receptacles and/or light switches installed.
Add these switches to your abrasive blasting hose to prevent it from spraying if the operator loses control. Also known as deadman switches, they prevent injuries and reduce wasted material by springing back to the off position when the operator lets go.