There are hundreds of cushioning pillows in every foot of these pliable mesh sheets. They're often used as a protective liner in drawers and cabinets and anywhere a nonskid surface is required.

These liners are treated to protect your tools against rust.

Keep tools and small parts in place and protected from damage.

A rubber seal in the lid keeps water out.

The slots in these low-profile organizers are a different color than the base so it's clear when tools are missing from your bench top or drawer.

The slots in these low-profile organizers are a different color than the base so it's clear when tools are missing.

Stretch these magnetic strips over corners and irregular surfaces.

Use these locks in a 3/4" dia. through hole, which is the most common through-hole size.

Choose these locks to use your own compatible lock cylinder to match the keying of an existing system.

Also known as compression cam locks, turn the handle a quarter-turn to latch, then another quarter-turn to draw the cam firmly against the door or drawer surface.

Made of plastic, these locks are suitable for damp and humid environments.

To prevent internal damage, these locks have a stainless steel shutter that blocks rain, snow, and dirt from entering the cylinder.

Offering more security than standard master keyed cam locks, these have circular keys that are difficult to duplicate.

These highly pick-resistant locks have specially designed half-moon keys that cannot be duplicated.

Made of plastic, these locks are suitable for damp and humid environments.

Use these locks in a 3/4" dia. through hole, which is the most common through-hole size.

Meet U.S. postal service guidelines for mailbox locks.

A stainless steel shutter blocks rain, snow, and dirt from entering the cylinder where they can cause internal damage.

The mounting screws on these locks are concealed to prevent tampering.

Open these locks with both a master key and their own unique key.

Also known as compression cam locks, these reach full compression when you lift the handle, turn it a quarter-turn, and then push it down for a secure hold.

Choose these locks if you need each one to open with a different key.

Also known as compression cam locks, turn the handle a quarter-turn to latch, then another quarter-turn to draw the cam firmly against the door or drawer surface.

Press the button and the handle snaps open; push the handle shut for a secure hold.

These tight-hold locks are IP65 and NEMA 4 rated for protection against dust, dirt, and washdowns. Press the button and the handle snaps open; push the handle shut for a secure hold.

Set a combination and reset it at any time.

Choose these cylinders if you need several cylinders that open with the same key.

Open several draw locks with the same key.

No need for a strike plate, these latches hook into a lip or notch.

Lift and turn the handle 180° to open and close these latches. Add a padlock to secure.

An integrated slide bolt extends into the strike plate to resist pull and vibration from side-to-side, front-to-back, and up-and-down forces.

Secure surfaces together with these padlockable latches; built-in compression springs withstand vibration better than other latches.

Each latch comes with a variety of strike plates for different mounting options.

These latches hook into a lip or notch and have an adjustable latching distance to compensate for gasketing and misalignment.

To secure overlapping components, pull the slide over the stud until they snap together. These latches resist shock and vibration.

Adjust the latching distance for a tight fit over gasketing and to compensate for misalignment.

Designed with compression springs to withstand vibration better than standard draw latches, these offer a more secure hold.

With a spring-loaded handle, these hold tighter than other turn-to-open draw latches and compensate for slight misalignment.

Use these L-handle latches to draw lightweight surfaces together.

To prevent accidental opening, these latches have a safety catch.

No need for a strike plate, these latches hook into a lip or notch.

These latches have a safety catch to prevent accidental opening.

A plastic-coated handle and hook prevents the release of particles from metal-to-metal contact, which makes these latches good for clean room applications.

Lift and turn the handle 180° to open and close these latches.

An integrated slide bolt extends into the strike plate to resist pull and vibration from side-to-side, front-to-back, and up-and-down forces.

Also known as paddle locks, these are often used on electrical panels, cabinets, and lockers.

Choose these hasps if you need hasps that each open with a different key.