These flashlights are built to handle everyday use. They have a slip-resistant grip to ensure a secure hold.

Made of stainless steel, these pocket-size flashlights have a smooth, easy-to-clean surface.

Clip these little flashlights to a baseball cap or a surface to light up your work.

Plug in these flashlights and they’ll automatically light up when the power goes out. There’s no need to regularly replace the batteries—they recharge on the base when it’s plugged into an outlet.

At full power, these flashlights shine as bright as a stadium light. They’re the brightest in our offering.

Always have a flashlight on hand—these attach to a key ring.

Tilt the head on these flashlights to aim light exactly where it's needed. They have a flat bottom, so you can work hands-free without them rolling away.

All of these flashlights stand up to wet environments.

Safely light up work in explosion-prone areas. Rated NEC Class I, these flashlights are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

Tilt the head on these flashlights to point light where you need it in explosion-prone areas. Rated NEC Classes I and II, they’re safe to use where there are ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust.

Light that moves with your gaze, not your grip. These headlamps provide hands-free illumination.

Light up work without risking an explosion. NEC rated, these headlamps are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

Light up work even when your visor is up. These headlamps come with three attachments that fit with anything from your hard hat to your baseball cap.

Illuminate small spaces and mark locations with these reusable lightsticks.

Aim light where it's needed most in areas that don't have an electrical outlet.

Power these lights with the same battery as your other cordless tools. They run on a Milwaukee M18 battery to light up work where there’s no outlet.

Because these lights are compatible with DeWalt rechargeable batteries, you can keep one type of cordless tool battery on hand. Their head pivots to aim light where it's needed in areas that don't have electrical power service.

A mounting clip at the base lets you attach these lights to nearby surfaces.

Hang these lights where you need them on the job site.

Hang a string of lights overhead to brighten wet jobsites. IP rated, these lights are sealed to keep out dust and moisture from washdowns, splashes, and sprays, even outdoors.

Pop these lights on magnetic surfaces to brighten wet spaces. Rated NEMA 6 and ETL listed, you can splash, spray, or dunk them in water, and they’ll keep working.

Light up large, open rooms where you need a quick setup and takedown, such as a room under construction. Just hang these lights from a ceiling up to 30' high and they’re ready to go.

Aim light where you need it—even in explosion-prone spaces—by raising, lowering, and tilting these lights on their tripod. Rated NEC Classes I, II, III, and Zone 0, they’re safe to use near ignitable concentrations of flammable or combustible gas, dust, or fibers.

Safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust, these lights are rated NEC Class I, Class II, and Zone 1.

Brighten remote areas, even if they’re damp or rainy. These floodlights are IP rated to keep out humidity and dripping, splashing, and falling liquids.

Bring light to remote areas with the DeWalt rechargeable battery that's already in your toolkit.

Compact and easy to carry, these ETL listed lights stand up to dripping, splashing, and falling liquids. The head adjusts up and down to direct light where it's needed.

Raise, lower, and tilt these lights to brighten your work in wet spaces.

Bring light to remote, wet areas. These floodlights are IP rated to handle humidity and dripping, splashing, and falling liquids. Adjust their tripod up and down to direct light as far as you need.

Brighten remote spaces with the DeWalt rechargeable battery that’s already in your toolkit. These floodlights extend up to 7 ft., and the light head turns at any angle to aim light where it’s needed.

With a slimmer profile than other strip machine lights, these lights fit in tight spots inside machinery because they don’t have a circuit board.

Mount these lights into a recessed opening on your machine—they sit flush against the surface for a streamlined appearance.

Illuminate machines or monitor processes in environments that reach up to 210° F. These lights have a thick housing that acts as a heat sink to protect the LEDs and driver from overheating.

Just like traditional tubular lights that illuminate your machine with a bright white light, these lights can also be programmed to switch over to a red or green light for communicating machine status.

Update conventional fluorescent tubular lights with newer LED technology. These lights match the diameter of most older lights and fit existing brackets without the need to drill new mounting holes.

Brighten countertops that your ceiling lights can’t reach. These lights are low-profile, so they won’t take up valuable workspace below your cabinets.

These lights cast a narrow beam of light. With a gooseneck arm, they are faster and easier to reposition than articulating-arm lights.

Stretch the arm to bring light directly over your work—even across a large surface. Also known as articulating arm lights, these lights have rigid sections that hold their position steady, including when fully extended.

Clip or clamp these lights near your work to illuminate what you’re working on without lighting up the whole room. Powered by a rechargeable battery, they’re often used in spaces where an outlet isn’t available.

The articulating arm on these lights holds its position better than gooseneck-arm lights, especially around vibration.

Pivot the head to cast a narrow beam of light to exactly where it's needed.

Shine light on machinery and through the sight glass on tanks to inspect food, brewery, chemical, pharmaceutical, and bio-tech processing lines.

A motion sensor turns on these lights when an enclosure door is opened. Mount them inside cabinets, closets, and other enclosed spaces.

Communicate a status at a glance by wiring these strip lights to change color when a part is malfunctioning inside your enclosure.

Brighten loading docks and trailers—these lights swing out from the wall and tilt to direct light where it’s needed.

Safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust, these lights are rated NEC Class I, II, and III.

Light up drawers and enclosures where power isn’t available—these lights are compact and powered by battery.

Spotlight fine details to find defects in parts or inspect dim machine interiors.

Hands-free like a benchtop magnifier and portable like a handheld magnifier, these are small enough to take with you and you don’t have to hold them.

Switch between UV light and white light to catch defects you'd otherwise miss with these hand-held magnifiers.

An LED on these loupes emits a focused, even beam so you don’t overlook any details.

More securely mounted than weighted-base magnifiers while taking up less space on your work surface, these illuminated magnifiers clamp to the side of a workbench.

Capture the extra-fine details you see under the magnifying lens in a photo or video.

Highlight fine details and defects on textured surfaces. These magnifiers cast light from an angle instead of from above like standard illuminated magnifiers.

Sturdy but flexible, these illuminated magnifiers have a weighted base to keep them still without tethering them to your workbench.