Sets include an assortment of keys. These simple tools turn fasteners from either end and reach into tight spots.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places.

These assorted keys have a retaining ring at the tip that grips inside the recess to ensure screws won’t fall off.

Often used to install carbide inserts in cutting tools, these keys have a small handle that prevents you from generating too much torque when turning a fastener.

These plastic organizers store keys in slots marked with the size.

Sets include assorted keys with long shafts that reach into tight spots. The plastic-covered handles provide a good grip for your whole hand.

Use the long shaft for more reach and the short shaft for more torque when turning fasteners.

The assorted keys in these sets have a small T-handle that prevents you from generating too much torque when turning a fastener. They are often used to install carbide inserts in cutting tools.

These assorted keys have a retaining ring on the tip that grips inside the recess to hold screws in place. Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

The toughest bits available, these withstand the shock and twisting force of impact drivers.

The slightly tapered tip wedges into the screw recess for a secure hold. These are also known as Torx-Align bits.

The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.

The toughest bits available, these withstand the shock and twisting force of impact drivers.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

An opening at the tip accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.

These screwdrivers have a soft, contoured handle that provides comfort and the best possible grip for achieving maximum torque.

These standard-length drivers are found in every tool box.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

Protect your stainless steel screws by using a stainless steel driver. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These drivers eliminate that risk.

Sets include assorted drivers with an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC, EN, or ASTM standards.

A ratchet mechanism turns fasteners more quickly than a standard bit driver. Insert a bit into the shaft and a magnet holds it in place.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet EN 60900 and IEC 60900.

An insulated handle and shafts protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900.

Bits have a different tip at each end and snap into the shaft, which is also a nutdriver.

Also known as ESD-safe screwdrivers, the handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Press the rotating end cap on the handle with your palm to apply constant pressure while turning the body of the screwdriver with your fingertips.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC, EN, or ASTM standards. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Ensure carbide inserts are tightened to the correct torque. These tools are set to the recommended torque values for each screw size.

These sockets are also known as pin-in-Torx bits.