Three times more accurate than standard totalizers for water, these are rated for ±1.5% accuracy.

The enclosure meets NEMA 4X to protect these totalizers from dust, washdowns, and corrosive liquids.

These totalizers meet NSF/ANSI Standard 61 for use in drinking water systems.

Flanged ends provide secure connections in large pipelines with high flow rates.

Measure the total flow volume of gasoline, diesel fuel, and kerosene.

More than twice as accurate as standard totalizers for fuel, these are rated for ±2% accuracy.

Determine the flow rate and total flow volume of water with the same meter.

For secure connections in large pipelines with high flow rates, these flowmeter/totalizers have flanged ends.

With a display that can be placed up to 25 feet from the sensor, these flowmeter/totalizers are often used in hard-to-access areas.

Union nuts on both ends make it easy to install and remove these flowmeters from your system.

Slot these counters into a control or electrical panel cutout.

These counters have mounting holes and a base plate for securing to a wall or work surface.

Slot these counters into a control or electrical panel cutout.

The digits displayed on these counters are visible up to 100 ft. away.

The digits displayed on these counters are visible up to 100 ft. away.

These counters do not require voltage to register a count.

These counters have mounting holes and a base plate for securing to a wall or work surface.

Slot these counters into a control or electrical panel cutout.

Wire these counters/ratemeters to an electrical pulse-emitting switch, sensor, or encoder to count input while tracking rates in units such as gallons per minute.

Slot these counters into a control or electrical panel cutout.

Send a signal to another device when the counter reaches a set point. The signal can start/stop a process or trigger an alarm.

These meters do not require voltage to register a count.

Roll these wheels along a surface to measure distances up to 99,999 feet.

Feed wire through the wheels inside the included counter to take measurements.

Combine a counter, feeder reel, coiler reel, and stand to create a wire, cable, and cord length measurer.

Tracking your machine component as it moves along a rotating threaded shaft, such as a spindle or lead screw, these indicators help you adjust machinery with speed and precision.

Count down to zero or count up to as much as 24 hours with these digital timers.

Record one event from start to finish with these traditional dial stopwatches.

Measure the position of an object moving in a straight line. Also known as string pots, these transmitters have an extending wire cable that measure the relative distance between two points.

The remote sensor with a cable lets you take pH readings in hard-to-reach areas.

Check your system for contaminants with this meter that detects total dissolved solids (TDS) in aquaculture solutions, wastewater, and other dirty liquids.

View conductivity readings of wastewater, boiler condensate, aquaculture solutions, and other dirty liquids up to 3 feet from the remote sensor to indicate the concentration of salts, nutrients, chemicals, and other substances.

Check the oxygen levels of water and other clean liquids in harsh field conditions. This meter has a housing that meets IP67 for complete resistance to dust and protection from temporary submersion.

Since these meters float and have a housing that meets IP67, they won’t be damaged by temporary submersion and have complete resistance to dust. They detect total dissolved solids (TDS) in water, hydroponic solutions, and other clean liquids to determine contaminant levels.

The remote probe on a 3-ft. cable limits your exposure when taking total dissolved solids (TDS) measurements to determine contaminant levels in aquaculture solutions, boiler condensate, contaminated water, and other dirty liquids.

Commonly used to test environmental samples, boiler condensate, wastewater, and other dirty liquids for contaminants, this bench-top meter determines the total dissolved solids (TDS) in a solution.

Check the pH and conductivity of water and other clean liquids with one bench-top device.

Test three different water-chemistry measurements in dirty, wet conditions. These meters have a housing that meets IP57 for good resistance to dust and protection from temporary submersion.