These bearings are rated IP69K as able to withstand washdown environments such as food, pharmaceutical, and chemical plants. Their fluoropolymer-coated housing is as corrosion resistant as 304 steel and safe for contact with food. The lubrication is NSF registered H1 for incidental contact with food. Because they’re permanently lubricated, these bearings are good for use in hard-to-reach areas or spaces that don’t receive regular maintenance. Also known as tapped base mounted ball bearings, they have threaded holes for fastening through the bottom to secure shafts in tight spaces. Having no mounting bolts on top makes them easier to clean, as well.

Set screw shaft mount bearings secure to shafts with no need for a collar. The set screw may cause marring on shafts.

Concentric lock shaft mount bearings center and secure shafts in the bearing bore. To install, tighten the single screw on the locking collar around its inner ring on your shaft. By gripping shafts firmly, they reduce vibration in your system for quieter operation.Block 3

Used in food, beverage, pharmaceutical, and chemical plants, these mounted ball bearings are IP69K certified for washdown environments and have a two-bolt flange for mounting. Their 316 stainless steel housing has excellent corrosion resistance and prevents rust caused by salt water, chlorine solutions, and chemicals. All have USDA H1 approved lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.

Set screw bearings grip shafts as you tighten their screw. They don’t use a collar, but the screw leaves some marring on shafts.

Clamp on bearings have a locking collar to center shafts and secure them better than set screw bearings, so there’s less vibration and noise. To install them, tighten the locking collar’s screw until it secures against the inner ring.

Snap optional covers onto bearings to protect them from moisture. Made of polypropylene, they resist corrosion, don’t absorb water, and are FDA compliant.

Permanently lubricated and IP69K certified for washdown environments, these mounted ball bearings are useful for hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. Mount them using their two-bolt flange. For excellent corrosion resistance and preventing rust caused by salt water, chlorine solutions, and chemicals, their housing is made of 316 stainless steel. All have NSF registered H1 lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.

Set screw shaft-mount bearings secure to shafts when you tighten the set screw, with no need for an additional collar. Set screws cause some amount of marring on shafts.

Concentric lock bearings have a locking collar to center shafts and secure them better than set screw bearings, so there’s less vibration and noise. Install them by tightening the locking collar’s screw until it presses against the inner ring.

Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, don’t absorb water, and are FDA compliant.

Made to withstand frequent washdowns, these bearings are permanently lubricated, which means you’ll never have to add lubricant. Use them in hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. With a 316 stainless steel housing, these bearings won’t rust from salt water, chlorine, or chemicals. All are lubricated with NSF registered H1 grease, which is certified for incidental contact with food.

Set-screw bearings secure to shafts as you tighten their screw. They don’t need a collar; however, the screws leave some marring on the shaft.

Concentric-lock bearings have a collar that centers and secures the shaft in the bearing bore. To install, tighten the single screw on the collar around its inner ring on your shaft. These bearings have a secure grip on the shaft that reduces vibration and noise.

Meeting IP69K for washdown environments, these mounted ball bearings are used in food, beverage, pharmaceutical, and chemical plants. They have excellent corrosion resistance and prevent rusting caused by salt water, chlorine solutions, and chemicals because their housing is 316 stainless steel. All have USDA H1 approved lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.

Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw does leave some marring on shafts.

Clamp on bearings have a locking collar to center shafts and secure them better than set screw bearings, so there’s less vibration and noise. To install them, tighten the locking collar’s screw until it grips the inner ring.

Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, won’t absorb water, and are FDA compliant.

Rated IP69K for washdowns, these bearings stand up to frequent cleanings in food, beverage, pharmaceutical, and chemical plants. They’re also suitable for incidental contact with food because they have NSF registered H1 lubricant. Made of stainless steel, these bearings are more corrosion resistant than steel bearings.

For technical drawings and 3-D models, click on a part number.