Use these fittings at pressures up to 9,000 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

Use with soft plastic tubing to prevent the tube from collapsing.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on stainless steel tubing that is flared to 37°.

The male pipe threads on these fittings have a sealant applied for extra protection against leaks.

Individually bagged to prevent contamination, these fittings are suitable for applications that require a high level of cleanliness.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included.

Use these sleeves with compression nuts and fittings to create a strong seal on stainless steel tubing.

Tighten these nuts onto high-pressure compression sleeves and fittings to create a strong seal on stainless steel tubing.

When used with high-pressure compression fittings and nuts, these sleeves bite into stainless steel tubing to form a strong seal.

Use at pressures up to 4,300 psi.

The flat face of the fitting connects to a tube adapter so you can slide the tubing and fitting sideways to disconnect in cramped spaces. They are also known zero-clearance fittings.

Create a strong seal on copper tubing when you couple these nuts with compression sleeves and fittings.

Also known as instrumentation fittings, these are made to tighter tolerances than standard compression fittings. They are compatible with Parker CPI fittings.

These fittings include a nut with a built-in sleeve, so there’s no need to remove the nut for assembly.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal.

Use these sleeves with compression nuts and fittings, sometimes called bite fittings, to create a strong seal on steel tubing. They are also known as ferrules.

Use these sleeves—also known as ferrules—with high-pressure compression nuts and fittings. They withstand about twice as much pressure as sleeves for standard compression fittings, so they’re good for hydraulic power applications.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

These fittings have two sleeves for extra gripping power. They bite into steel tubing as you tighten the nut to form a strong seal.

A tube adapter sits flush against the flat face of the fitting so you can slide the steel tubing and fitting sideways to disconnect in cramped spaces. Also known as zero-clearance fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight seal on tubing that is flared to 37°.

With the best corrosion resistance of any metal fitting we offer, these Hastelloy fittings will stand up to aggressive chemicals and are resistant to pitting and stress cracking. Also known as instrumentation fittings, they include a nut with two sleeves.

Couplings are metal, which has better durability than plastic cam-and-groove hose couplings. They consist of a plug and a socket that connect and disconnect quickly. Use them if you need frequent access to a line. To connect, insert the plug into the socket and push the levers down.

To minimize fluid loss when connecting and disconnecting your line, these couplings have flat faces for a close fit and shut-off valves to stop the flow—they meet ISO 16028, which is an international standard for hose couplings.

Also known as live swivels, these fittings swivel continuously 360° before and after installation. This not only makes installation easier, but also eliminates the twisting and kinking that can cause hose failure. Fittings are threaded on both ends so you can connect them directly to a threaded hose or to pumps, cylinders, and other equipment in your hydraulic system. Use in high-pressure applications up to 5,000 psi.

These two-piece fittings screw directly onto the hose without the need for a separate adapter. When assembled, the fitting compresses against the hose, forming a strong seal. Also known as reusable fittings, they can be unscrewed from the hose end and used on a new hose. Use in high-pressure hydraulic applications up to 5,800 psi.

Use these couplings at pressures up to 6,500 psi. They consist of a plug and socket that connect and disconnect quickly. Use them if you need frequent access to a line. They are compatible with Snap-Tite H-Shape plugs and sockets.

Use these couplings at pressures up to 4,500 psi. Also known as flush-face couplings, the plugs and sockets have a flat face, which allows them to mate close together, reducing fluid loss when connecting and disconnecting the line. They are compatible with International Standard ISO Minimal-Spill-shape plugs and sockets.

Use these couplings at pressures up to 5,000 psi. They consist of a plug and socket that connect and disconnect quickly. Use them if you need frequent access to a line. They are compatible with International Standard ISO A-shape plugs and sockets.

Slide the barbed end of these swivels into your dispensing hose and connect with a clamp. They rotate before and after installation as needed to prevent hose from twisting, kinking, and wearing prematurely.

Distribute air or fluid to multiple locations from a single supply source with these manifolds. They are also known as headers.

These manifolds have two separate sections inside, so you can run two different substances through them without worrying about them intermixing. Also known as headers.

Mount these manifolds on the end of a hose line to distribute air or fluid to three locations from a single supply source.

When you’re short on vertical space, these manifolds are a good fit—they have outlets on the side instead of on top, so they have a lower profile than rectangular manifolds. Use them to distribute air or fluid to five locations from a single supply source.

Use these junction blocks to organize and separate multiple lines in your system. They have threaded holes that allow air or fluid to flow straight through the block.