A silicone rubber coating on this fiberglass sleeving protects against sparks and molten metal splash.

A specially formulated silicone rubber coating allows this sleeving to stretch to twice its relaxed ID to fit over items during installation; it then tightens around its contents for a secure fit.

Use this PTFE sleeving in applications where temperatures reach up to 500° F.

With a temperature rating of 1800° F or higher, this sleeving can withstand hotter temperatures than fiberglass and most ceramic.

A blend of Aramid and fiberglass gives this sleeving excellent abrasion resistance. It can withstand temperatures up to 650° F

Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.

Rated UL 2024 and NFPA 262, this sleeving is approved for use in plenum spaces such as duct work and above a drop ceiling. It self-extinguishes and emits minimal amounts of smoke and gas during combustion. Stretch to fit over items for easy installation; it tightens around its contents for a secure fit.

Protect cable, hose, and pipe in high temperature environments—this sleeving withstands temperatures over 450° F. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Reduce the likelihood of slipping in high-traffic areas. This sleeving has thick, nonslip fibers that create friction so it doesn’t slide when you step on it. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Use this braided copper sleeving to protect wire and cable from signal distortion caused by nearby equipment and devices. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

A slit along the length makes this sleeving easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.

Rated UL94V2, this sleeving resists combustion and minimizes the spread of flames. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. It has impact and abrasion resistance similar to conduit, with more flexibility.

This sleeving reflects heat away from contents and withstands temperatures up to 900° F. The corrugated construction gives it impact and abrasion resistance similar to conduit, but with more flexibility.

The two halves of this sleeving nest into each other, fully enclosing contents. It has interlocking ridges that overlap to keep out dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

A strip of hook-and-loop creates a strong seal along the entire length of this sleeving, yet it can be opened at any point to access contents. Use it to wrap around wire, cable, or hose without disconnecting them.

Snaps keep this sleeving securely closed, yet permit quick access to contents and allow you to route wires in between the snaps. Use it to easily wrap around wire, cable, and hose without disconnecting them.

Wrap this sleeving around wire, cable, and hose without disconnecting them. It has a slit along the entire length and wraps over itself to stay closed without an adhesive strip or other closure.

Unlike traditional sleeving that bunches wire and cable into a circle, this sleeving holds them flat, so it’s good for tight spaces such as vehicle interiors. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

Often used in robotics and other automated applications, this highly flexible sleeving withstands continuous motion without tearing or fraying. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Coated with PVC, this polyester sleeving resists chemicals and solvents. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

This sleeving absorbs UV light, so it can be used in direct sunlight without getting damaged. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Protect cables, cords, and wire and form them into bundles in your food-processing plant while lowering the risk of contaminating the food.

A mica and silicone rubber blend allows this sleeving to withstand temperatures up to 2100° F. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.

Made of woven polyolefin/polyester fabric, this tubing has excellent abrasion resistance so it can be dragged over rough surfaces without damage.

Resistant to diesel fuel, hydraulic fluid, and lubricating oil, this tubing is often used in vehicles.

After being cleaned with alcohol, this tubing is bagged and sealed in a clean room. It's certified for material quality and purity.

A layer of conductive cloth protects wire and cable from signal interference caused by nearby equipment and devices.

This tubing shrinks down to a quarter of its original ID, so it creates a tight seal over irregularly shaped objects. It withstands up to 500° F.

A flame-retardant additive makes this polyolefin tubing combustion resistant and minimizes the spread of flames.

Extra-thick walls provide better protection against abrasion and tears than standard moisture-seal tubing, as well as creating a water-resistant seal.

Approved for contact with food, this tubing is FDA Compliant 21 CFR 177.1330.

Made of PVDF, this tubing has excellent cut and abrasion resistance. It has a flame-retardant additive that resists combustion and minimizes the spread of flames.

Also known as halogen-free tubing, this tubing produces minimal amounts of smoke and gas if exposed to an open flame, so it can be used in enclosed areas such as ships and tunnels.

With thin walls, this tubing shrinks faster than other high-temperature tubing. It withstands up to 500° F.

Protect bus bars and other high-voltage devices—this tubing withstands voltages up to 15,000 volts.

Made of PVC, this tubing resists chemicals, oil, and solvents. The adhesive lining creates a water-resistant seal when heated.

Use this wrap with heat-shrink tubing to create a moisture-resistant seal. Apply it like tape around wire and cable, then slide the tubing over the wrap. The wrap melts when tubing is heated and bonds to the underlying surface.

Also known as breakout boots, these splitters insulate and seal the point where wire splits off from cable, or where cables exit from conduit.

Keep general purpose tubing in a variety of sizes on hand.

Seal the end of crimped connections, such as motor coils, to protect them from moisture.

Thread cable and hose through the entire length.

Designed for smooth, quiet travel, these carriers minimize clicking and jumping in vibration-sensitive applications such as printing and scanning.

Capable of turning and flexing up to 380° in any direction, these carriers are a perfect match for robotic arms.

Use in areas with light pedestrian traffic.

Lay your cable in the slit on the top so it stays off the floor.

These cable ramps are strong enough to withstand equipment traffic.

With the widest channels of any of our cable ramps, these ramps can span large cable, hose, and pipe.

These are the most corrosion-resistant tray systems we offer.

The zinc plating on these tray systems offers good corrosion resistance.

The large domed head extends beyond the diameter of your pipe, rod, or tubing for added protection.

More durable than plastic caps, these provide the most protection from abrasion and impact.

A long, textured pull tab provides a sure grip for quick removal even when wearing gloves.

Slide these caps over a tool handle or other round object and use the eye to hang it.

Good for electroplating, paint baking, and powder-coating applications, these caps withstand temperatures up to 440° F or 570° F.

Keep equipment safe from electrical currents with these caps that have a surface resistivity of less than 10¹² ohms.

Slide these flexible vinyl caps on and they conform for a snug fit.

These flexible plastic caps are tapered to fit a variety of unthreaded and threaded objects.

Made of silicone, these caps withstand temperatures of 450° F for electroplating, paint-baking, and powder-coating applications. All of these flexible caps are tapered to fit a variety of unthreaded and threaded objects.