About Plastic and Rubber Tubing
More
About Durometer Hardness Scales
More
Hard Plastic Tubing for Air and Water
This general purpose tubing has hard walls, yet is flexible enough for gradual bends. It has excellent strength and durability.
Nylon tubing can handle lower temperatures than polypropylene tubing and can withstand higher pressures. It has slightly softer walls than polypropylene tubing, making it more flexible and impact absorbent.
Opaque tubing doesn’t allow you to see what’s flowing through the line. Semi-clear tubing gives you a limited view inside the line.
For technical drawings and 3-D models, click on a part number.
- Semi-Flexible
- Compatible with Compression and Push to Connect Tube Fittings
- Hard (Rockwell R78)
- Temperature Range: -60° to 200° F
ID | OD | Wall Thick. | Bend Radius | Max. Pressure | Max. Vacuum | Lengths, ft. | Per Ft. | |
Inch | ||||||||
---|---|---|---|---|---|---|---|---|
Black | ||||||||
9/32" | 3/8" | 3/64" | 1 1/2" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 0000000 | 00000 | |
Blue | ||||||||
9/32" | 3/8" | 3/64" | 1 1/2" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 0000000 | 0000 | |
Green | ||||||||
9/32" | 3/8" | 3/64" | 1 1/2" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 0000000 | 0000 | |
Red | ||||||||
9/32" | 3/8" | 3/64" | 1 1/2" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 0000000 | 0000 | |
Yellow | ||||||||
9/32" | 3/8" | 3/64" | 1 1/2" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 0000000 | 0000 |
- Semi-Flexible
- Compatible with Compression and Push to Connect Tube Fittings
- Hard (Rockwell R78)
- Temperature Range: -60° to 200° F
Self-Retracting Hard Plastic Tubing for Air and Water
- Semi-Flexible
- Compatible with Barbed and Push to Connect Tube Fittings
- Hardness:
Inch: Hard (Rockwell R80)
Metric: Hard (Rockwell R75) - Temperature Range: -40° to 180° F
Keep your work area tidy with this coiled tubing that extends when you need it and retracts out of the way when you don’t. Tubing is made of tough and abrasion-resistant nylon. It is semi-flexible, so it is good for gradual bends.
Semi-clear tubing gives you a limited view inside the line. Opaque tubing doesn’t allow you to see what’s flowing through the line.
Note: Length refers to the length you can extend the tubing. Overstretching can cause the tubing to lose its ability to fully retract back to its normal state. Retracted length refers to the length of the tubing when coiled.
For technical drawings and 3-D models, click on a part number.
ID | OD | Wall Thick. | Coil OD | Lg. | Retracted Lg. | Max. Pressure | Max. Vacuum | Each | |
Nylon Plastic | |||||||||
---|---|---|---|---|---|---|---|---|---|
Semi-Clear White | |||||||||
9/32" | 3/8" | 3/64" | 2 1/4" | 6 1/2 ft. | 6" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 000000 |
9/32" | 3/8" | 3/64" | 2 1/4" | 17 1/2 ft. | 12" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
9/32" | 3/8" | 3/64" | 2 1/4" | 25 ft. | 17" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
Opaque Black | |||||||||
9/32" | 3/8" | 3/64" | 2 1/4" | 6 1/2 ft. | 6" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
9/32" | 3/8" | 3/64" | 2 1/4" | 17 1/2 ft. | 12" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
9/32" | 3/8" | 3/64" | 2 1/4" | 25 ft. | 17" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
Opaque Blue | |||||||||
9/32" | 3/8" | 3/64" | 2 1/4" | 6 1/2 ft. | 6" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
9/32" | 3/8" | 3/64" | 2 1/4" | 17 1/2 ft. | 12" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
9/32" | 3/8" | 3/64" | 2 1/4" | 25 ft. | 17" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
Opaque Green | |||||||||
9/32" | 3/8" | 3/64" | 2 1/4" | 6 1/2 ft. | 6" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
9/32" | 3/8" | 3/64" | 2 1/4" | 17 1/2 ft. | 12" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
9/32" | 3/8" | 3/64" | 2 1/4" | 25 ft. | 17" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
Opaque Orange | |||||||||
9/32" | 3/8" | 3/64" | 2 1/4" | 6 1/2 ft. | 6" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
9/32" | 3/8" | 3/64" | 2 1/4" | 17 1/2 ft. | 12" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
9/32" | 3/8" | 3/64" | 2 1/4" | 25 ft. | 17" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
Opaque Red | |||||||||
9/32" | 3/8" | 3/64" | 2 1/4" | 6 1/2 ft. | 6" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
9/32" | 3/8" | 3/64" | 2 1/4" | 17 1/2 ft. | 12" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
9/32" | 3/8" | 3/64" | 2 1/4" | 25 ft. | 17" | 250 psi @ 72° F | 28 in. of Hg @ 72° F | 00000000 | 00000 |
UV-Resistant Hard Plastic Tubing for Chemicals
Ultraviolet light won’t cause this FEP (fluorinated ethylene propylene) tubing to degrade or deteriorate.
FEP tubing is the most economical option.
Semi-clear tubing gives you a limited view inside the line. Opaque tubing does not allow you to see inside the line.
Semi-flexible tubing is good for gradual bends. Tubing that meets UL 94 V-0 is flame retardant, so it delays the spread of flames to valuable equipment.
For technical drawings and 3-D models, click on a part number.
- Semi-Flexible
- Compatible with Compression and Push to Connect Tube Fittings
- Hard (Durometer 55D)
- Temperature Range: 32° to 212° F
- Semi-Flexible
- Compatible with Compression and Push to Connect Tube Fittings
- Hard (Durometer 55D)
- Temperature Range: 32° to 212° F
Abrasion-Resistant Hard Plastic Tubing for Chemicals
This durable tubing has the best abrasion and wear resistance of all our hard tubing for chemicals. It can withstand a variety of acids and other harsh substances. Tubing is semi-clear, so you get a limited view inside the line. It is semi-flexible, so it’s good for gradual bends.
ETFE tubing can withstand a wider temperature range than PVDF tubing and can also handle vacuum applications. It has a super-smooth interior for unrestricted flow and easy cleaning. It meets ASTM D3159 specifications and testing requirements for material quality.
For technical drawings and 3-D models, click on a part number.
Grommets
Push these flexible grommets into place to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth, insulated holes. Commonly used in metal panels, they also damp vibration. All of these grommets have a medium hardness rating to offer a balance of cushioning and impact resistance.
SBR grommets have good abrasion resistance. They are not for use outdoors.
Buna-N grommets withstand a wider range of temperatures than other grommets and resist abrasion, oil, and grease. They are not for use outdoors.
Grommets that meet MIL-G-3036 resist hot petroleum-based oil and coolant.
For technical drawings and 3-D models, click on a part number.
For Hole Dia. (A) | For Material Thick. (B) | ID (C) | Flange Dia. (D) | Overall Ht. (E) | Hardness Rating | Hardness | Temp. Range, °F | For Use Outdoors | Color | Pkg. Qty. | Pkg. | |
SBR Rubber | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
3/8" | 1/16" | 9/32" | 9/16" | 1/4" | Medium | Durometer 55A | -30° to 170° | No | Black | 100 | 0000000 | 000000 |
3/8" | 1/16" | 9/32" | 19/32" | 13/64" | Medium | Durometer 55A | -30° to 170° | No | Black | 100 | 0000000 | 00000 |
7/16" | 1/16" | 9/32" | 5/8" | 1/4" | Medium | Durometer 55A | -30° to 170° | No | Black | 100 | 0000000 | 00000 |
15/32" | 1/16" | 9/32" | 37/64" | 5/16" | Medium | Durometer 55A | -30° to 170° | No | Black | 50 | 0000000 | 00000 |
7/8" | 3/32" | 9/32" | 1 1/8" | 11/32" | Medium | Durometer 55A | -30° to 170° | No | Black | 50 | 0000000 | 00000 |
7/8" | 1/8" | 9/32" | 1 1/8" | 3/8" | Medium | Durometer 55A | -30° to 170° | No | Black | 25 | 0000000 | 00000 |
15/16" | 3/32" | 9/32" | 1 1/8" | 11/32" | Medium | Durometer 55A | -30° to 170° | No | Black | 25 | 0000000 | 00000 |
For Hole Dia. (A) | For Material Thick. (B) | ID (C) | Flange Dia. (D) | Overall Ht. (E) | Hardness Rating | Hardness | Temp. Range, °F | For Use Outdoors | Specifications Met | Color | Pkg. Qty. | Pkg. | |
Buna-N Rubber | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
3/8" | 1/16" | 9/32" | 9/16" | 1/4" | Medium | Durometer 50A | 0° to 250° | No | MIL-G-3036 | Black | 10 | 00000000 | 00000 |
13/32" | 1/16" | 9/32" | 9/16" | 1/4" | Medium | Durometer 50A | 0° to 250° | No | MIL-G-3036 | Black | 10 | 00000000 | 0000 |
For Hole Dia. (A) | For Material Thick. (B) | ID (C) | Flange Dia. (D) | Overall Ht. (E) | Hardness Rating | Hardness | Temp. Range, °F | For Use Outdoors | Color | Pkg. Qty. | Pkg. | |
SBR Rubber | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
3/8" | 5/32" | 9/32" | 5/8" | 11/32" | Medium | Durometer 55A | -30° to 170° | No | Black | 100 | 0000000 | 000000 |
Fabric Grommets
Press these grommets into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material. Use a cutting punch (sold separately) to create the hole, then set the grommet using either an installation punch or a press (both sold separately). Grommet trade size refers to the hole size and the size of the installation tool needed. All of these grommets can be used outdoors.
Grommets with a tooth lock washer keep material from loosening and rotating better than those with a standard washer.
Grommets that meet NASM16491 and NASM20230 adhere to military dimensional standards.
Brass grommets are strong and have good corrosion resistance. Nickel-plated brass grommets have more corrosion resistance than brass grommets. Aluminum grommets are lightweight and have good corrosion resistance. Stainless steel grommets have excellent corrosion resistance, making them the best choice for harsh environments. They also have good chemical resistance.
Hammer-driven cutting punches create holes for installing grommets when you strike them with a wooden or rawhide mallet. Hammer-driven installation punches set grommets in a hole when you strike them with a wooden or rawhide mallet. Manual presses set grommets in a hole when you squeeze the adjustable pliers-grip handle. Requires a die set (sold separately).
For technical drawings and 3-D models, click on a part number.
Grommet Trade Size | For Max. Material Thick. | ID (C) | Flange Dia. (D) | Dp. Under Flange (F) | For Use Outdoors | Specifications Met | Pkg. Qty. | Pkg. | |
Brass | |||||||||
---|---|---|---|---|---|---|---|---|---|
1 | 0.108" | 9/32" | 0.687" | 0.185" | Yes | NASM20230 | 50 | 0000000 | 00000 |
Nickel-Plated Brass | |||||||||
1 | 0.108" | 9/32" | 0.687" | 0.185" | Yes | NASM16491 | 50 | 00000000 | 00000 |
Aluminum | |||||||||
1 | 0.108" | 9/32" | 0.687" | 0.185" | Yes | __ | 50 | 0000000 | 0000 |
Stainless Steel | |||||||||
1 | 0.108" | 9/32" | 0.687" | 0.185" | Yes | __ | 25 | 00000000 | 00000 |
For Grommet Trade Size | For Hole Dia. | Material | Each | |
1 | 9/32" | Steel | 0000000 | 000000 |
For Grommet Trade Size | For Hole Dia. | Each | |
1 | 9/32" | 0000000 | 000000 |
Throat | |||||
---|---|---|---|---|---|
Max. Opening | Dp. | Wd. | Material | Each | |
7/8" | 3 1/4" | 1 3/4" | Aluminum | 000000000 | 0000000 |
For Grommet Trade Size | Hole Size | Each | |
1 | 9/32" | 000000000 | 000000 |
Rolled-Rim Reinforcing Fabric Grommets
A rolled rim provides added grip while the elongated neck and teeth on the washer, also known as a spur washer, add reinforcement and reduce rotation so you can use these grommets in thick materials such as canvas. Press the grommets into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material. Use a cutting punch (sold separately) to create the hole, then set the grommet using either an installation punch or a press (both sold separately). Grommet trade size refers to the hole size and the size of the installation tool needed. All of these grommets can be used outdoors.
Grommets with a tooth lock washer keep material from loosening and rotating better than those with a standard washer.
Grommets that meet MIL-G-16491, NASM20230, and AN230 adhere to military dimensional standards.
Brass grommets are strong and have good corrosion resistance. Nickel-plated brass grommets have more corrosion resistance than brass grommets. Stainless steel grommets have excellent corrosion resistance, making them the best choice for harsh environments. They also have good chemical resistance.
Hammer-driven cutting punches create holes for installing grommets when you strike them with a wooden or rawhide mallet. Hammer-driven installation punches set grommets in a hole when you strike them with a wooden or rawhide mallet. Manual presses set grommets in a hole when you squeeze the adjustable pliers-grip handle. Requires a die set (sold separately).
For technical drawings and 3-D models, click on a part number.
Grommet Trade Size | For Max. Material Thick. | ID (C) | Flange Dia. (D) | Dp. Under Flange (F) | For Use Outdoors | Specifications Met | Pkg. Qty. | Pkg. | |
Brass | |||||||||
---|---|---|---|---|---|---|---|---|---|
0 | 0.096" | 9/32" | 0.67" | 0.175" | Yes | MIL-G-16491, NASM20230, AN230 | 50 | 0000000 | 000000 |
Nickel-Plated Brass | |||||||||
0 | 0.096" | 9/32" | 0.67" | 0.175" | Yes | MIL-G-16491, NASM16491, NASM20230, AN230 | 50 | 00000000 | 00000 |
Stainless Steel | |||||||||
0 | 0.096" | 9/32" | 0.67" | 0.175" | Yes | __ | 10 | 00000000 | 00000 |
For Grommet Trade Size | For Hole Dia. | Material | Each | |
0 | 1/4" | Steel | 0000000 | 000000 |
For Grommet Trade Size | For Hole Dia. | Each | |
0 | 9/32" | 0000000 | 000000 |
Throat | |||||
---|---|---|---|---|---|
Max. Opening | Dp. | Wd. | Material | Each | |
7/8" | 3 1/4" | 1 3/4" | Aluminum | 000000000 | 0000000 |
For Grommet Trade Size | Hole Size | Each | |
0 | 9/32" | 000000000 | 000000 |
Fabric Grommet Kits
Kits include grommets, a cutting punch, a cutting block, an installation punch, and a die set. Use them to create a way to run rope and cable through tarps, covers, and curtains. Press the grommets into a hole you've already cut. They can also be used to strengthen and prevent existing holes from fraying in material. Use the cutting punch to create the hole, then set the grommet using the installation punch and die set. Made of brass, all of these grommets are strong and have good corrosion resistance. They adhere to military dimensional standard MIL-G-16491. They can also be used outdoors.
Grommets with a tooth lock washer keep material from loosening and rotating better than those with a standard washer.
For technical drawings and 3-D models, click on a part number.
Grommet Trade Size | For Max. Material Thick. | ID (C) | Flange Dia. (D) | Dp. Under Flange (F) | For Use Outdoors | Specifications Met | Includes | No. of Grommets | Each | |
Grommets with Standard Washer | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
Brass | ||||||||||
1 | 0.1" | 9/32" | 0.687" | 0.185" | Yes | MIL-G-16491 | Cutting Punch, Cutting Block, Installation Punch, Die Set | 24 | 0000000 | 000000 |
Grommets with Tooth Lock Washer | ||||||||||
Brass | ||||||||||
1 | 0.12" | 9/32" | 0.687" | 0.185" | Yes | MIL-G-16491 | Cutting Punch, Cutting Block, Installation Punch, Die Set | 48 | 0000000 | 00000 |
Reinforcing Fabric Grommets
The extended neck on the washer of these grommets adds reinforcement so you can use them in thicker material such as woven fabrics. Press them into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material. Use a cutting punch (sold separately) to create the hole, then set the grommet using either an installation punch or a press (both sold separately). Grommet trade size refers to the hole size and the size of the installation tool needed. All of these grommets adhere to military dimensional standards MIL-G-16491, NASM20230, and AN230. They can be used outdoors.
Brass grommets are strong and have good corrosion resistance. Nickel-plated brass grommets have more corrosion resistance than brass grommets.
Hammer-driven cutting punches create holes for installing grommets when you strike them with a wooden or rawhide mallet. Hammer-driven installation punches set grommets in a hole when you strike them with a wooden or rawhide mallet. Manual presses set grommets in a hole when you squeeze the adjustable pliers-grip handle. Requires a die set (sold separately).
For technical drawings and 3-D models, click on a part number.
For Grommet Trade Size | For Hole Dia. | Material | Each | |
1 | 9/32" | Steel | 0000000 | 000000 |
For Grommet Trade Size | For Hole Dia. | Each | |
1 | 9/32" | 0000000 | 000000 |
Throat | |||||
---|---|---|---|---|---|
Max. Opening | Dp. | Wd. | Material | Each | |
7/8" | 3 1/4" | 1 3/4" | Aluminum | 000000000 | 0000000 |
For Grommet Trade Size | Hole Size | Each | |
1 | 9/32" | 000000000 | 000000 |
Self-Piercing Fabric Grommets
The sharp neck on these grommets cuts the material as you press them into place, eliminating the need for a cutting punch. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material. To install, use a die set and bench-mount manual press (both sold separately). Grommets with grommet trade size 0, 1, and 2 require a die set adapter for installation. Grommet trade size refers to the grommet's hole size once set. Made of brass, all of these grommets are strong and have good corrosion resistance.
Grommets with a tooth lock washer, also known as a spur washer, have an elongated neck and teeth for extra reinforcement so you can use these grommets in thick materials such as canvas. They also have a rolled rim, which provides added grip.
For technical drawings and 3-D models, click on a part number.
Grommet Trade Size | For Max. Material Thick. | ID (C) | Flange Dia. (D) | Dp. Under Flange (F) | For Use Outdoors | Pkg. Qty. | Pkg. | |
Brass | ||||||||
---|---|---|---|---|---|---|---|---|
0 | 0.126" | 9/32" | 0.688" | 0.189" | No | 50 | 0000000 | 000000 |
Throat Dp. | Press Ht. | Frame Material | Ram Material | Mounting Fasteners Included | Each | |
4 3/4" | 8" | Iron | Steel | No | 000000000 | 0000000 |
Grommets with Standard Washer
and Grommets with Tooth Lock Washer
For Grommet Trade Size | Each | |
For Grommets with Tooth Lock Washer | ||
---|---|---|
0 | 0000000 | 0000000 |