A base that lights up draws attention to emergency stops. When pushed, these switches immediately cut power. All meet IEC and ISO standards for emergency stop applications. Mount them in a standard panel cutout. Installation requires an additional 9 mm cutout for the illuminated ring.

Additional contact blocks (sold separately) can be added to control more circuits or replace the included contact blocks.

For technical drawings and 3-D models, click on a part number.

Immediately cut power with a single push. These switches meet EN 418 for compliance with European machine directives for emergency stop applications. All have positive force contacts that will open a circuit when actuated even if a spring fails or the contacts stick. They include enough contact blocks to control the number of circuits listed.

Pull reset, illuminated pull reset, and turn reset switches are rated NEMA 4, 13, and IP66. Contact blocks for these switches are rated IP20.

Additional contact blocks (sold separately) can be added to control more circuits, or replace the included contact block.

For technical drawings and 3-D models, click on a part number.

A quick push is all it takes to actuate these simple switches. Mount them in a standard panel cutout diameter. The contact block is rated IP20. Switches include enough contact blocks to control the number of circuits listed. For an easy way to tell different switches apart, choose a different actuator color for each or label them with legend plates (not included).

Illuminated switches are easy to see in dim and dark areas.

NEMA and IP rated, all switches seal out dust, water from washdowns, and splashing oil or coolant. NEMA 3S rated switches function in cold temperatures, even when covered in ice. IP69K rated switches are protected from high-pressure washdowns.

Note: Illuminated switches include a bulb. If wiring the switch and the bulb to the same circuit, the circuit voltage must not exceed bulb voltage.

Mounting tools (sold separately) make it easier to install switches in crowded panels.

Additional contact blocks (sold separately) can be added to control more circuits, or replace the included contact block.

For technical drawings and 3-D models, click on a part number.

Immediately cut power with a single push. These switches are rated for protection from low-pressure streams of water and oil/coolant spraying. They have positive force contacts that will open a circuit when actuated even if a spring fails or the contacts stick. Mount them in a standard panel cutout.

Turn twist switches back on by twisting the button and pull switches by pulling it. Add an optional lockout (sold separately) on either kind to cover the button and prevent changes to its position.

Additional contact blocks (sold separately) can be added to control more circuits or replace the included contact blocks.

Actuate these switches with the push of a button. Their buttons are distinct colors to help you quickly spot switches without labels. Install them in a standard panel cutout. Rated NEMA 4X and NEMA 13, these switches withstand corrosion, washdowns, and oil/coolant spraying.

Guards (sold separately) protect switches from damage and prevent accidental actuation. They work with 1 9/16" diameter mushroom switches that control one circuit.

These switches include enough contact blocks to control the number of circuits listed. Additional contact blocks (sold separately) can be added to control more circuits, or replace the included contact block.

For technical drawings and 3-D models, click on a part number.

Actuate these switches with a quick push. A housing seals in anything that could ignite flammable material, so you can use them where ignitable gas and dust may be present. You’ll know they’re safe because they meet NEC Class I Div. 2, Groups B, C, D for hazardous locations. Install them in a standard panel cutout.

Mushroom switches have a button that sticks out from the panel. Because they’re easy to identify and actuate, these switches are often used to stop equipment. They have a twist reset, so they’ll return to their starting position when you rotate the button.

Switches come with a contact block for each number of circuits they control. Additional contact blocks (sold separately) can be added to control more circuits, or to replace the included contact block.

For technical drawings and 3-D models, click on a part number.

Immediately cut power with a single push. These switches meet EN 418 for compliance with European machine directives for emergency stop applications. They're rated NEMA 4, 13, and IP65 for protection from washdowns and oil/coolant spraying.

Made of yellow polycarbonate plastic, these enclosed switches are easy to see and resist dents, chips, and cracks. They are more corrosion resistant than aluminum enclosed switches and withstand washdowns and oil/coolant spraying. Mount them to a wall or attach a cord grip to position them at your workstation. They have positive force contacts that will open a circuit when actuated, even if a spring fails or the contacts stick. A single push will immediately cut power.

The switches can be reset by manually pulling, turning or unlocking them by key.

For technical drawings and 3-D models, click on a part number.

A red light flashes when the actuator is pushed, making it easy to see from a distance. These switches immediately cut power with a single push. They're housed in a protective yellow enclosure for quick identification. All have positive force contacts that will open a circuit when actuated even if a spring fails or the contacts stick. They're rated IP65 for protection from water projected by a nozzle.

Note: If wiring the switch and the bulb to the same circuit, the circuit voltage must not exceed bulb voltage.

Auxiliary contacts allow you to add a signaling device or control another switch.

For technical drawings and 3-D models, click on a part number.