Also known as I-line fittings, these fittings have a male adapter that interlocks with a female adapter for more support than standard quick-clamp fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on stainless steel tubing that is flared to 37°.

Individually bagged to prevent contamination, these fittings are suitable for applications that require a high level of cleanliness.

A PTFE seal on the tube end of these fittings allows for an extra-strong connection in high-vibration applications.

The thick walls of these fittings can withstand more than twice the pressure of standard compression fittings.

Instead of a metal sleeve (ferrule), these fittings have a rubber sleeve that cushions tubing and absorbs vibration to maintain a tight seal, even when connected to large pumps.

For applications that require an extra level of cleanliness, these fittings are individually bagged to prevent contamination.

Use at pressures up to 4,300 psi.

Originally used on satellites, rocket propulsion systems, and even Mars rovers, these fittings will handle your most challenging industrial environments. They're designed to withstand high vibration and ultra-high vacuum without generating particles that could disrupt your operation.

Fittings are polished to a32 Ra and under finish on the interior.

An alternative to bolt-together fittings, these fittings handle larger tube OD sizes than quick-clamp fittings. Also known as ISO-K high-vacuum fittings, the clamps have claws that grab hold of fittings with flanged ends.

Create access points in ultra-high-vacuum lines or chambers by bolting two same-size flanges together with a copper gasket between them. The flanges’ sharp edges dig into the copper gasket and form an extremely tight seal, which means they handle higher vacuum pressures than other high-vacuum fittings with rubber gaskets.

For high-vacuum systems with tube sizes too large for quick-clamp (KF) fittings, choose these bolt-together fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

These fittings have two sleeves for extra gripping power. They bite into steel tubing as you tighten the nut to form a strong seal.

Thicker walls make these fittings—sometimes called flareless or bite fittings—withstand about twice as much pressure as standard compression fittings, so they’re good for hydraulic power applications.

Use these fittings in an air vacuum system to avoid the hassle of brazing and welding. Insert two fittings into a clamp and tighten to form a secure seal in steel tubing.

The flared end of the fitting nests inside the fitting body, providing extra support to the tubing. Fittings are also known as inverted 45° flared fittings.

When cleanliness is crucial to your application, choose these fittings that are individually cleaned and bagged to prevent contamination.

A nut with two sleeves (ferrules) gives these fittings extra gripping power. The sleeves bite into tubing as you tighten the nut, creating a strong seal.

Create a strong connection without heating, flaring, or soldering.

With a nickel-plated finish, these compression fittings resist corrosion better than plain brass fittings.

Crimp these fittings to copper tubing with a crimping tool for a leak-tight connection that doesn’t require heat or soldering. They are comparable to Viega ProPress fittings.

Choose these metal fittings when you need better durability than our plastic push-to-connect fittings.

These Monel fittings have the corrosion resistance to handle hydrofluoric and sulfuric acid. Also known as instrumentation fittings, they include a nut with two sleeves.

For use in high-vacuum systems, these fittings use a metal reinforced O-ring to create an airtight seal. Also known as KF, QF, and NW fittings, they’re used for high-vacuum applications such as vacuum coating and heat treating, leak testing, and analyzing gases.

Made of PVDF (also known as Kynar), these fittings have excellent strength and can handle temperatures as high as 240° F or 270° F.

Also known as instant fittings, these connect to tubing with a push, and an internal gripping ring and O-ring hold the tubing tight. Use in applications up to 150 psi.

Create corrosion-resistant connections in food and beverage lines with just a push. Also known as instant fittings, these fittings have an internal gripping ring and an O-ring that hold tight to tubing.

Made of stainless steel, these fittings are more durable than plastic barbed tube fittings for food and beverage.

A smooth interior reduces friction and prevents product buildup, ensuring an unrestricted flow.

These quick-disconnect couplings meet NSF/ANSI 169 for food equipment.

These quick-disconnect couplings mate with a sanitary stainless steel quick-clamp fitting for use in dairy lines.

Barbs grip onto tubing.

Monitor flow with these clear fittings.

The nickel plating on these fittings provides better corrosion resistance than unplated brass fittings.

Made of stainless steel, these fittings have better corrosion resistance than brass fittings.

Made of brass, these fittings resist corrosion from water and are more durable than plastic and aluminum fittings.

Made of nickel-plated brass, these tube fittings resist corrosion better than plain brass fittings. The male threaded ends connect to NPT, NPTF, BSPP, BSPT, and other universal threads, so you don’t have to bother matching exact thread types.

Make lightweight connections without the hassle of matching the exact thread type—these fittings connect to NPT, NPTF, BSPP, BSPT, and other universal threads.

Made of nickel-plated brass, these fittings have better corrosion resistance than unplated brass fittings.

Withstanding up to 300° F, these fittings have the highest temperature rating of all our brass push-to-connect tube fittings for air and water.

Ball bearings allow these fittings to rotate 360°, even after they are tightened. They have a special seal that reduces friction to allow for continuous rotation.

These fittings won’t absorb moisture, so they’re good for water and high-humidity air applications.

Connect high-pressure brake lines with fittings that won’t crack in frigid temperatures. Often used on commercial trucks and trailers, these fittings meet Department of Transportation FMVSS 571 safety standards.

A built-in shut-off valve stops the flow when you separate these couplings, so air or water won’t leak from your line. Made of nylon, these couplings are lightweight and have good impact and abrasion resistance.

Made of plastic, these couplings are lighter in weight than metal luer lock couplings. They're a popular choice in labs because of their versatility—they fit any other luer lock plug, socket, syringe, or needle.

Made of brass, these couplings are more durable than plastic couplings.

A spring-free flow path allows more air or water to pass through these tube couplings at lower line pressures than other quick-disconnect couplings.

Not only are these chrome-plated brass couplings corrosion resistant, they’re also durable enough to handle pressures up to 250 psi and can be used with vacuum.

Don’t get your lines crossed—use one of these couplings to quickly connect or disconnect multiple tubes at once.

Lighter in weight than their metal counterparts, these compression fittings are polypropylene.

These fittings include a nut with a built-in sleeve (ferrule), so there’s no need to remove the nut for assembly.

A single sleeve (ferrule) compresses the tubing as you tighten the nut on these fittings, creating a strong seal. They are brass for good corrosion resistance.

Also known as instant fittings, they connect to tubing with a push, and an internal gripping ring and O-ring hold the tubing tight. Use in applications up to 140 psi.

A staple in labs, these couplings are highly versatile, fitting any luer lock plug, socket, syringe, or needle. They’re PVDF, so they resist most acids, alcohols, and organic solvents.

Also known as instant fittings, these chemical-resistant plastic fittings connect to tubing with a push. An internal gripping ring holds the tubing tight.

Fittings have a sleeve that bites into tubing as you tighten the nut to form a seal in applications up to 120 psi. Also known as flareless fittings.

Quick-disconnect couplings consist of a plug and a socket that join with a latch so you can easily connect and disconnect your line. Use in applications up to 150 psi.

Connect these fittings to tubing with a ring and a crimping tool (both sold separately). Safe to use with drinking water, these fittings meet the strict standards of NSF/ANSI 61.

Fittings can withstand temperatures up to 200° F.

These fittings are strong enough to handle extreme pressures, yet small enough to fit into cramped spaces.

Typically used with extreme-pressure iron and steel threaded pipe fittings. Also known as Schedule XXH.

For use in noncorrosive environments, these fittings have better strength than our low-pressure iron and steel pipe fittings.

With better strength than our low-pressure steel flanges, these are for use in medium-pressure applications.

Typically used with medium-pressure galvanized iron and steel threaded pipe fittings. Also known as Schedule 80.

Also known as Pressure Class 1500 steel flanges, these have the strength to handle high pressures.

Combine an adapter with a two-piece pipe flange (sold separately) to build a customized flange connection for noncorrosive environments.

The galvanized finish on these fittings provides fair corrosion resistance. Fittings are for use in low-pressure applications.

To prevent leaks in low-pressure lines, the male threads on these fittings have an acrylic sealant already applied for extra protection.

Use these Pressure Class 150 pipe flanges in low-pressure lines where temperatures drop down to -40° F.

These flanges are for low-pressure applications in noncorrosive environments.

Also known as Schedule 40, this steel pipe is designed for low-pressure applications.

With thicker, stronger walls than our standard-wall butt-weld pipe fittings, these fittings stand up to your high strength applications.

Even in temperatures as low as -46°, these A350 LF2 steel flanges won’t become brittle, so they absorb impact better than other low-pressure steel flanges.

Bolt two flanges of the same size together with a gasket to create an access point in a pipe line.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

Also known as Code 61 SAE hydraulic flanges.

Also known as no-hub pipe fittings and soil pipe fittings, these fittings are for use in gravity-flow applications both above and below ground.

Plated with nickel, these brass fittings resist rust better than steel and unfinished brass fittings. Select them when you need more strength in corrosive environments to handle higher pressures than our low-pressure fittings.

Use these fittings in low-pressure flow applications. They have good corrosion resistance.

Also known as Pressure Class 150 flanges, these brass flanges are designed for low-pressure applications.

Less than an inch in length, these miniature fittings work well in low-pressure pipe lines that are tight on space.

Use these heavy-duty brass fittings for high-pressure drinking water applications.

Install and remove these high-pressure brass fittings with a socket wrench or hex key (sold separately).

The plating on these brass fittings creates a shiny finish and provides extra protection in corrosive environments. Fittings have the strength to handle high-pressure applications.

Extreme pressures are no problem for these heavy-duty brass fittings.