Use these valves in general purpose applications such as those with water, oil, air, and inert gas.

For applications that require intermittent operation, such as spraying and washing, push or pull the lever on these valves to start flow. They spring closed when the lever is released.

For installation through thick insulation, these valves have an extra-long stem. They’re for use with water, oil, air, inert gas, and steam.

Install these low-profile valves in tight spots. Use with water, oil, air, and inert gas.

For installation in instrument panels, these valves have threads and a hex nut below the handle. They’re for use with water, oil, air, and inert gas.

These valves are rated for at least three times the pressure of standard threaded valves. Use with water, oil, air, inert gas, and steam.

For fast installation and removal from pipelines, these valves have a union fitting that disassembles into multiple pieces. They’re for use with water, oil, air, inert gas, and steam.

Install these low-profile valves in tight spots. They are for use with water, oil, air, and inert gas.

Plastic provides a lightweight and economical alternative to metal. All valves have barbs that grip onto tubing for a secure hold. They’re for use with water, oil, air, and inert gas.

Clean and maintain these valves without removing welded connections. They have a three-piece bolted body that disassembles inline for easy access to internal components. Use with water, oil, air, inert gas, and steam.

Use these plastic valves for a lightweight and economical alternative to metal. They have a compression sleeve that bites into tubing as you tighten the nut, forming a strong seal. Use with water, air, and inert gas.

For use in drinking water systems, these valves meet NSF/ANSI 61.

There’s no need to unbolt these valves for cleaning—remove the valve handle and slide the valve apart for inline access to internal components. Also known as elliptical valves, they have a fluoroelastomer seal and a polypropylene body to withstand aggressive and corrosive solutions in chemical-processing applications.

Barbs grip onto tubing, providing a secure hold. To withstand aggressive and corrosive solutions in chemical-processing applications, these valves have a plastic body and a chemical-resistant seal.

These valves have barbs that grip onto tubing, providing a secure hold. All meet NSF/ANSI 18 for use with manual food and beverage dispensing equipment.

Protect personnel and equipment in the presence of diesel fuel, fuel oil, gasoline, and kerosene. Fire-tested to meet American Petroleum Institute (API) 607, Edition 4, these valves are designed to securely isolate fluid and prevent the spread of fire.

These solenoid valves operate on electricity to automatically start and stop flow. The actuator is directly mounted to the valve body to minimize movement and reduce wear.

Control flow in high-pressure lines in tight spots—these valves have the highest pressure ratings of our compact valves.

To fit in tight spots, these valves have a slimmer body than standard valves with an exhaust port.

These valves are rated for use in hazardous locations with flammable gas and combustible dust.

Built to withstand the extreme cold of liquid nitrogen and liquid oxygen, these valves are cleaned and bagged for high-purity applications.

A built-in strainer traps debris and allows you to replace the screen without disconnecting your pipeline.

Often used to control single-acting, spring-return air cylinders, these valves have a third threaded port to exhaust media.

Install these valves in gas pipelines to automatically control the flow of natural gas, propane, and butane to equipment.

For use in general purpose applications with water, oil, and inert gas.

Valves are for use with water, oil, air, inert gas, and steam. They gradually open and close to adjust and regulate flow.

Rated for twice the pressure of other threaded flow-adjustment valves, these are often used in refineries and other demanding environments. Use with water, oil, air, and inert gas. They gradually open and close to adjust and regulate flow.

The color-coded threads and numerical markings on these valves ensure consistent and repeatable settings. One full revolution of the handle reveals a new color to indicate the set point. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Often used in hydraulic and compressed air systems, these valves can withstand at least 6,000 psi. They’re for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Also known as block and bleed valves, these have two vent ports to isolate pressure gauges, switches, and other components in high-pressure systems for maintenance, calibration, and sampling without interrupting the process. They are rated for up to 10,000 psi. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For installation in instrument panels, these valves have a hex nut and threads below the handle. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Also known as block and bleed valves, these have a vent port that allows you to remove instrumentation equipment attached to the valve without depressurizing your line. Turn the handle to shut off flow and remove the vent port plug to drain liquid trapped in the valve. Use them with water, oil, air, and inert gas. These valves adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

With 45° flared tube fittings, these valves form a tight seal on metal tubing. Use with air. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

To withstand a maximum steam pressure of at least 4,800 psi @ 355° F in applications such as petroleum refineries, these valves are machined from a single piece of metal for seamless construction. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

These valves divert flow between ports. Use with water, oil, air, and inert gas.

Also known as shuttle valves, these automatically switch the inlet source as pressure changes; they always direct flow from the higher-pressure side-port inlet to the top-port outlet. Use them with water, oil, air, and inert gas.

For a lightweight alternative to metal valves, these have a plastic body. To fit in tight spots, they have a low-profile handle and a short end-to-end length. Valves are for use with water, oil, air, and inert gas. All divert flow between ports.

There’s no need to unbolt these valves for cleaning—remove the handle and slide the valve apart for inline access to internal components. Also known as elliptical valves, they have a fluoroelastomer seal and a polypropylene body for diverting flow in chemical-processing applications.

Lower profile than other solenoid diverting valves and available in smaller pipe sizes, these valves are often used to automatically divert flow between ports in tight spots. Use them with water, oil, air, and inert gas. All operate on electricity.

For use with threaded pipe, these valves are available with NPT, NPTF, BSPP, BSPT, and UNI/UNF (JIC) connections.

To achieve the maximum possible flow, internal components are designed to reduce flow resistance.

Plastic provides a lightweight alternative to metal.

The heat-resistant rubber seal withstands temperatures up to 500° F.

Barbs grip onto tubing, providing a secure hold.

Insert tubing into the fitting—no heat, solder, or flux required.

These valves open to allow flow in one direction and close when flow stops or reverses.

Insert tubing into the fittings—no heat, solder, or flux required.

For more than twice the temperature rating of standard check valves for oil and fuel, these have a heat-resistant fluoroelastomer seal that can withstand temperatures up to 500° F.

Rated for at least four times the pressure of standard check valves for oil and fuel, these are often used in hydraulic applications with pressures up to 3,000 psi.

Valves have NPT connections for use with threaded pipe.

Connect these orifices to threaded pipe, or insert them into threaded holes.

Insert the barbed ends of these orifices into rubber and soft plastic tubing, and secure them with a clamp.

Also known as Schrader valves, these valves rapidly fill or empty compressed air tanks or pneumatic tires.

Sockets accommodate five common plug shapes: Industrial, ARO, Lincoln, Tru-Flate, and European.

Also known as automotive couplings. Compatible with Tru-Flate-shape plugs and sockets.

Compatible with Lincoln-shape plugs and sockets.

Compatible with Japanese-shape plugs and sockets.

To minimize fluid loss when connecting and disconnecting your line, these couplings have flat faces for a close fit and shut-off valves to stop the flow—they meet ISO 16028, which is an international standard for hose couplings.

Use these couplings at pressures up to 7,200 psi. Also known as flush-face couplings, the plugs and sockets have a flat face, which allows them to mate close together, reducing fluid loss when connecting and disconnecting the line. They are compatible with International Standard ISO Minimal-Spill-shape plugs and sockets.

Distribute air or fluid to multiple locations from a single supply source with these manifolds. They are also known as headers.

Designed for ultra-clean environments, these manifolds are cleaned, dried, and vacuum sealed in plastic to prevent dirt and moisture from contaminating the inside. Use them to distribute air or fluid to multiple locations from a single supply source. Also known as headers.

When you’re short on vertical space, these manifolds are a good fit—they have outlets on the side instead of on top, so they have a lower profile than rectangular manifolds. Use them to distribute air or fluid to five locations from a single supply source.

With outlets on the side instead of on top, these manifolds have a lower profile than rectangular manifolds and fit well in cramped spaces. Use them to distribute air or fluid to three locations from a single supply source.

Use these junction blocks to organize and separate multiple lines in your system. They have threaded holes that allow air or fluid to flow straight through the block.

These fittings won’t absorb moisture, so they’re good for water and high-humidity air applications.

Make lightweight connections without the hassle of matching the exact thread type—these fittings connect to NPT, NPTF, BSPP, BSPT, and other universal threads.

Start and stop flow with a quarter turn of the handle. Also known as ball valves.

Adjust the flow rate as needed.

Set your flow rate and then adjust it as necessary; these valves maintain flow rate despite pressure changes in the system.

Also known as check valves, these open to allow flow in one direction and close when flow stops or reverses.

Build a custom 1/4" system to deliver coolant, cutting oil, water, or air in any direction.

Also known as thermostatic steam traps, these increase the efficiency of your radiator by venting cool air.