For applications that require intermittent operation, such as spraying and washing, push or pull the lever on these valves to start flow. They spring closed when the lever is released.

These valves can handle at least twice the pressure of other compact valves. Install them in tight spots. Use with water, oil, air, and inert gas.

For installation in instrument panels, these valves have threads and a hex nut below the handle. They’re for use with water, oil, air, and inert gas.

Use these valves with water, air, and inert gas.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. They’re for use with water, oil, air, and inert gas.

For more durability than plastic valves, these are made of metal. A compression sleeve bites into tubing as you tighten the nut, forming a strong seal. Use these valves with water, oil, air, inert gas, and steam.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. To withstand aggressive and corrosive solutions, they have a chemical-resistant fluoroelastomer seal and a plastic body.

Lower profile and available in smaller connection sizes than standard valves, these fit in tight spots.

Comparable to Asco Red Hat 8210G Series and Parker Gold Ring 23C Series, these valves meet the highest quality standards.

These valves are rated for use in hazardous locations with flammable gas and combustible dust.

The color-coded threads and numerical markings on these valves ensure consistent and repeatable settings. One full revolution of the handle reveals a new color to indicate the set point. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Often used in hydraulic and compressed air systems, these valves can withstand at least 6,000 psi. They’re for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

A compression sleeve bites into tubing as you tighten the nut, forming a strong seal. These valves are for use with air. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Threads and a hex nut below the handle let you install these valves through instrument panels. They are for use with water, oil, air, and inert gas. All divert flow between ports.

A metal body provides more strength and durability than plastic. These valves have a low-profile handle and a short end-to-end length to fit in tight spots. All are for use with water, oil, air, and inert gas. They divert flow between ports.

Lower profile than other solenoid diverting valves and available in smaller pipe sizes, these valves are often used to automatically divert flow between ports in tight spots. Use them with water, oil, air, and inert gas. All operate on electricity.

For use with threaded pipe, these valves are available with NPT, NPTF, BSPP, BSPT, and UNI/UNF (JIC) connections.

At 1 1/2" long or less, these valves fit in confined spaces.

Rated for up to twice the pressure of standard check valves, these can withstand pressures up to 3,000 psi.

Barbs grip onto tubing, providing a secure hold.

With internal components that resist wear from frequent operation, these valves can cycle as often as once per second.

Connect these orifices to threaded pipe, or insert them into threaded holes.

Also known as Schrader valves, these valves rapidly fill or empty compressed air tanks or pneumatic tires.

The industry standard for quick-disconnect couplings, these are also known as industrial interchange couplings. Compatible with Industrial-shape plugs and sockets.

Distribute air or fluid to multiple locations from a single supply source with these manifolds. They are also known as headers.

Designed for ultra-clean environments, these manifolds are cleaned, dried, and vacuum sealed in plastic to prevent dirt and moisture from contaminating the inside. Use them to distribute air or fluid to multiple locations from a single supply source. Also known as headers.

When you’re short on vertical space, these manifolds are a good fit—they have outlets on the side instead of on top, so they have a lower profile than rectangular manifolds. Use them to distribute air or fluid to five locations from a single supply source.

With outlets on the side instead of on top, these manifolds have a lower profile than rectangular manifolds and fit well in cramped spaces. Use them to distribute air or fluid to three locations from a single supply source.

Use these junction blocks to organize and separate multiple lines in your system. They have threaded holes that allow air or fluid to flow straight through the block.

These fittings won’t absorb moisture, so they’re good for water and high-humidity air applications.

Start and stop flow with a quarter turn of the handle. Also known as ball valves.

Adjust the flow rate as needed.

Build a custom 1/4" system to deliver coolant, cutting oil, water, or air in any direction.