Extend your reach in hard-to-access areas—turn these valves on and off using a square ratchet to grasp the hole at the end of the handle. Use with water, oil, air, and inert gas.

Attach a pressure gauge to the side port on these valves. Use with water and air.

A built-in strainer traps debris and allows you to replace the screen without disconnecting your pipeline.

These valves are rated for at least three times the pressure of standard threaded valves. Use with water, oil, air, inert gas, and steam.

For fast installation and removal from pipelines, these valves have a union fitting that disassembles into multiple pieces. They’re for use with water, oil, air, inert gas, and steam.

Use these valves with water, air, and inert gas.

These valves have union fittings that disassemble for fast installation and removal from pipelines. Use with water, air, and inert gas.

Plastic provides a lightweight and economical alternative to metal. All valves have barbs that grip onto tubing for a secure hold. They’re for use with water, oil, air, and inert gas.

Attach these valves to industry-standard two-bolt flanges on circulation pumps from manufacturers such as Bell and Gossett, Taco, Grundfos, and Armstrong. Use with water, air, and steam.

Clean and maintain these valves without removing welded connections. They have a three-piece bolted body that disassembles inline for easy access to internal components. Use with water, oil, air, inert gas, and steam.

Weld these valves to unthreaded metal pipe for a permanent, flush connection that permits smooth flow through a line. Use with water, oil, inert gas, and steam.

For fast installation and removal from pipelines, these valves have union fittings that disassemble into multiple pieces. Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves meet NSF/ANSI 61 for use in drinking water lines.

Disassemble the union fittings on these valves for fast installation and removal from your pipeline. All meet NSF/ANSI 61 for use with drinking water.

Use these valves with garden hose and other landscaping equipment. All meet NSF/ANSI 61 for use with drinking water.

The most chemical-resistant threaded valves we offer, these have a PTFE seal and an alloy body that can withstand extremely aggressive and corrosive chemicals, such as methyl ethyl ketone and toluene.

The three-piece bolted body comes apart for access to internal components without unthreading pipe connections and removing the valve from your line. Seal is fluoroelastomer and body is polypropylene for excellent resistance to aggressive and corrosive solutions in chemical-processing applications.

Union fittings on both ends of these valves disassemble for fast installation and removal from your pipeline. Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves have a fluoroelastomer seal and a plastic body that can withstand aggressive and corrosive solutions in chemical-processing applications.

Install these low-profile valves in low-clearance pipelines for natural gas, propane, and butane.

Designed for use in refineries and other demanding environments, these durable valves have a forged steel body that can withstand at least twice the pressure of other threaded valves.

These valves have socket-weld connections for bonding to unthreaded male plastic pipe.

Bond the socket-weld connections on these valves to unthreaded male plastic pipe.

These top-of-the-line valves are comparable to Asco Red Hat 8210G Series and Parker Gold Ring 23C Series.

These valves are rated for use in hazardous locations with flammable gas and combustible dust.

Built to withstand the extreme cold of liquid nitrogen and liquid oxygen, these valves are cleaned and bagged for high-purity applications.

Use with coolant and detergent such as ethylene glycol or soap solutions.

To change the flow rate of antifreeze and cleaning solutions, use the adjustment screw or knob to manually set how much these valves will open when actuated.

With a plastic body and a fluoroelastomer seal, these valves can stand up to aggressive and corrosive solutions in chemical-processing applications.

The three-piece bolted body comes apart for access to internal components without unthreading pipe connections and removing the valve from your line.

A compact, lightweight actuator and an angular body allow you to install these valves in any mounting orientation.

Also known as diaphragm valves, these have a diaphragm that can handle dirty liquid, slurries, and abrasive media without damage.

Also known as diaphragm valves, these have a diaphragm that can handle dirty liquid, slurries, and abrasive media without damage.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components.

Insert unthreaded pipe into the socket ends and bond with PVC primer and cement to create a permanent, leak-tight connection.

All valves have threaded NPT connections.

Use these valves for boiler maintenance and other low-pressure plumbing applications. They're for use with water. All gradually open and close to adjust and regulate flow.

For lightweight and corrosion-resistant alternative to metal, these valves are plastic. Attach garden hose to the valve outlet. Use with water. These valves gradually open and close to adjust and regulate flow.

Rated for twice the pressure of other threaded flow-adjustment valves, these are often used in refineries and other demanding environments. Use with water, oil, air, and inert gas. They gradually open and close to adjust and regulate flow.

Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection. These valves are for use with water, oil, air, inert gas, and steam. They gradually open and close to adjust and regulate flow.

Designed to withstand the extreme cold of liquid argon, liquid carbon dioxide, and liquid nitrogen, these valves are cleaned and bagged to meet CGA G-4.1 standards for oxygen service. They gradually open and close to adjust and regulate flow.

Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Often used in hydraulic and compressed air systems, these valves can withstand at least 6,000 psi. They’re for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

With a gauge port on each side of these valves, you can install two different pieces of instrumentation equipment to simultaneously monitor multiple media properties without interrupting flow. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For faster actuation than motor-driven valves, these operate on compressed air. Integrate them into PLC systems for automatic control over the valve position based on system conditions. The actuator has a built-in electric pilot valve that controls the air supply to the valve. Set how much to open the valve using the programmable controller on the actuator.

Control flow in two directions from a single source—these valves have two handles for independent operation of each outlet. Use them with water, oil, and inert gas.

There’s no need to unbolt these valves for cleaning—remove the handle and slide the valve apart for inline access to internal components. Also known as elliptical valves, they have a fluoroelastomer seal and a polypropylene body for diverting flow in chemical-processing applications.

For easy installation and removal from pipelines, all ends on these valves have union fittings that disassemble into multiple pieces. Their fluoroelastomer seal and plastic body can withstand aggressive and corrosive solutions for diverting flow between ports in chemical-processing applications.

Often installed on petroleum loading arms to test fuel quality without interrupting flow, these valves are fire-tested to meet American Petroleum Institute (API) 607, Edition 5, for securely isolating fluid and preventing the spread of fire.

For use with threaded pipe, these valves have NPT connections. Use them with water, oil, air, and inert gas. All operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.

To achieve the maximum possible flow, internal components are designed to reduce flow resistance.

Plastic provides a lightweight alternative to metal.

With few moving parts to wear out, these valves withstand frequent opening and closing, pulsating flow, and rapid flow reversal.

Barbs grip onto tubing, providing a secure hold.

Less than half the end-to-end length of standard flange-mount check valves, these can be installed in pipelines with limited clearance.

Visually inspect flow and debris accumulation through the transparent valve body.

To reduce installation time and allow for maintenance without detaching pipe connections, these valves have union fittings.

Visually inspect flow and debris accumulation through the transparent valve body.

These heavy duty valves can withstand pressures up to 1,975 psi and temperatures up to 800° F.

Plastic provides a lightweight alternative to metal.

For more durability than plastic, these valves have a metal body.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection.

Rated for 12 times the pressure of standard vacuum-breaking valves, these can handle up to 1,500 psi. Connections are NPT.

Integral shutoff valves isolate flow for inline maintenance, and a top-entry cover provides easy access to internal components.

Also known as flow restrictors and precision orifice valves, these orifices are used to throttle, vent, bleed, or regulate flow in water systems.

To minimize fluid loss when connecting and disconnecting your line, these couplings have flat faces for a close fit and shut-off valves to stop the flow—they meet ISO 16028, which is an international standard for hose couplings.

Use these couplings at pressures up to 5,000 psi. They consist of a plug and socket that connect and disconnect quickly. Use them if you need frequent access to a line. They are compatible with International Standard ISO B-shape plugs and sockets.

Unlike other manifolds, which have an inlet on either end, these have one inlet on the opposite side from the outlets. This design allows air or fluid to follow a straight path, improving flow through your system. Also known as headers.

With outlets on the side instead of on top, these manifolds have a lower profile than rectangular manifolds and fit well in cramped spaces. Use them to distribute air or fluid to three locations from a single supply source.

Use these manifolds with molding equipment to circulate hot and cold water through your line. They have a red side for hot water and a blue side for cold water.

Lock the handle using a padlock.

A tapered needle gives you more precise control than standard flow-adjustment inline hydraulic valves.

Also known as check valves, these open to allow flow in one direction and close when flow stops or reverses.

When input pressure varies, use these valves to maintain a consistent pressure.

To set the pressure, unscrew the cap and turn the adjusting screw.