Extend your reach in hard-to-access areas—turn these valves on and off using a square ratchet to grasp the hole at the end of the handle. Use with water, oil, air, and inert gas.

For installation through thick insulation, these valves have an extra-long stem.

These valves handle twice the pressure of other compact valves. Install them in tight spots, such as where pipelines are crowded together. Use with water, oil, air, and inert gas.

Access the handle of these valves while protecting your line behind an instrument panel. They have threads and a hex nut below the handle for panel mounting.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components. Use with water, oil, air, inert gas, and steam.

Use these valves with water, air, and inert gas.

For extra gripping power and a strong seal, the Yor-Lok fittings on these valves have two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. These valves are for use with water, oil, air, and inert gas.

Barbs grip onto tubing, giving these valves a secure hold. Made of plastic, they won’t pit or corrode on the inside like metal valves, and they’re lighter in weight for easy handling.

Clean and maintain these valves without removing welded connections. They have a three-piece bolted body that disassembles inline for easy access to internal components. Use with water, oil, air, inert gas, and steam.

Insert your tubing into the fittings of these valves with just a push—the internal rings will grip it tight. Made of plastic, these valves are a lightweight alternative to metal valves. All meet NSF/ANSI 61 for safe use with drinking water.

For use in drinking water systems, these valves meet NSF/ANSI 61.

No need to completely remove these valves from your line for cleaning and repairs. The bolted three-piece body comes apart, so you can easily access their internal components.

Start and stop flow to your drinking water system without worrying about leaks. These valves have a compression sleeve that bites into tubing as you tighten the nut.

There’s no need to unbolt these valves for cleaning—remove the valve handle and slide the valve apart for inline access to internal components. Also known as elliptical valves, they have a fluoroelastomer seal and a polypropylene body to withstand aggressive and corrosive solutions in chemical-processing applications.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. To withstand aggressive and corrosive solutions, they have a chemical-resistant fluoroelastomer seal and a plastic body.

Push tubing into the fittings on these valves and an internal gripping ring and O-ring hold it tight—no heat, solder, or flux required. They meet either NSF/ANSI standards or are FDA compliant for use with food.

Control flow in lines where preventing leaks is critical, such as bottling lines. These valves have a compression sleeve that bites into tubing as you tighten the nut.

A low-profile handle allows these valves to fit in low-clearance pipelines for diesel fuel, fuel oil, and kerosene.

Use these valves as a mainline shutoff in natural gas and propane pipelines.

Often used in HVAC or refrigeration systems, these valves are designed to control the flow of ammonia, nitrogen, and other harsh chemicals.

Designed for use in refineries and other demanding environments, these valves have a durable body that can withstand nearly twice the pressure of other gradual on/off valves.

With a forged steel body and bolted construction, these valves can withstand nearly 10 times the pressure of other socket-connect gradual valves.

Limit wear and damage in high-cycling applications—these valves have additional seals that prevent leakage to reduce maintenance time.

These solenoid valves operate on electricity to automatically start and stop flow. The actuator is directly mounted to the valve body to minimize movement and reduce wear.

Lower profile and available in smaller connection sizes than standard valves, these fit in tight spots.

Avoid pressure surges and system shocks that can damage piping by installing these valves that open and close slowly.

Built to withstand the extreme cold of liquid nitrogen and liquid oxygen, these valves are cleaned and bagged for high-purity applications.

A built-in strainer traps debris and allows you to replace the screen without disconnecting your pipeline.

Safe for automated on/off control in drinking-water systems, these valves meet NSF/ANSI Standard 61.

Supply fuel oil to boilers, furnaces, and other equipment.

Use these valves for boiler maintenance and other low-pressure plumbing applications. They're for use with water. All gradually open and close to adjust and regulate flow.

Also known as whistle valves, these open and throttle as force is applied to the lever and automatically close upon release. They’re commonly used for spraying, washing, and other applications that require manual discharge of liquid and air. Use with water, oil, air, and inert gas.

To automatically shut off the flow of diesel fuel, fuel oil, kerosene, and oil in case of fire, these valves automatically close and the handle permanently fuses in place when the ambient temperature reaches 165° F.

The color-coded threads and numerical markings on these valves ensure consistent and repeatable settings. One full revolution of the handle reveals a new color to indicate the set point. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

To ensure consistent and repeatable settings, these valves have color-coded handle threads and numerical markings. One full revolution of the handle reveals a new color to indicate the set point. Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

To ensure highly precise flow adjustment, these valves adjust flow in smaller increments than other valves for finer control over the flow rate in metering and sampling applications. Use them with water, oil, air, and inert gas.

To withstand a maximum steam pressure of at least 4,800 psi @ 355° F in applications such as petroleum refineries, these valves are machined from a single piece of metal for seamless construction. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Valves have NPT connections for use with threaded pipe. Turn the handle to adjust the flow of butane, diesel fuel, fuel oil, gasoline, kerosene, natural gas, and propane in small increments.

Threads and a hex nut below the handle let you install these valves through instrument panels. They are for use with water, oil, air, and inert gas. All divert flow between ports.

For use with threaded pipe, these valves have NPT connections. Use them with water, oil, air, and inert gas. All operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.

The motor on these valves can handle diverting applications with high flow rates and pressures. They operate on electricity to automatically divert flow between ports.

To achieve the maximum possible flow, internal components are designed to reduce flow resistance.

Plastic provides a lightweight alternative to metal.

The heat-resistant rubber seal withstands temperatures up to 500° F.

For more durability than plastic barbed check valves, these have a stainless steel body.

Insert tubing into the fitting—no heat, solder, or flux required.

These valves open to allow flow in one direction and close when flow stops or reverses.

Plastic provides a lightweight alternative to metal.

Valves have NPT connections for use with threaded pipe.

Compression fittings bite down on the outside of hard metal tubing for a secure connection.

Made of acetal, these couplings are lighter in weight than metal quick-disconnect couplings. Compatible with Plastic-shape plugs and sockets.

Sockets accommodate five common plug shapes: Industrial, ARO, Lincoln, Tru-Flate, and European.

Compatible with Lincoln-shape plugs and sockets.

Compatible with Japanese-shape plugs and sockets.

Compatible with Schrader-shape plugs and sockets.

Use these couplings at pressures up to 10,000 psi. Also known as flush-face couplings, the plugs and sockets have a flat face, which allows them to mate close together, reducing fluid loss when connecting and disconnecting the line. They are compatible with High-Pressure Minimal-Spill-shape plugs and sockets.

Use these couplings at pressures up to 10,000 psi. The plug and socket thread together to form a stronger connection than other quick-disconnect couplings. They are compatible with High-Pressure Thread-Lock-shape plugs and sockets.

Use these couplings at pressures up to 5,000 psi. They consist of a plug and socket that connect and disconnect quickly. Use them if you need frequent access to a line. They are compatible with International Standard ISO A-shape plugs and sockets.

These manifolds have two separate sections inside, so you can run two different substances through them without worrying about them intermixing. Also known as headers.

Unlike other manifolds, which have an inlet on either end, these have one inlet on the opposite side from the outlets. This design allows air or fluid to follow a straight path, improving flow through your system. Also known as headers.

When you’re short on vertical space, these manifolds are a good fit—they have outlets on the side instead of on top, so they have a lower profile than rectangular manifolds. Use them to distribute air or fluid to five locations from a single supply source.

Use these manifolds with molding equipment to circulate hot and cold water through your line. They have a red side for hot water and a blue side for cold water.

Use these junction blocks to organize and separate multiple lines in your system. They have threaded holes that allow air or fluid to flow straight through the block.

Made of brass, these fittings have good corrosion resistance.

These fittings won’t absorb moisture, so they’re good for water and high-humidity air applications.

Lighter in weight than their metal counterparts, these quick-disconnect couplings are made of acetal plastic. They are moisture resistant, so they won’t absorb water and lose strength, even in high-humidity environments.

A spring-free flow path allows more air or water to pass through these tube couplings at lower line pressures than other quick-disconnect couplings.

A spring-free flow path allows more chemicals to pass through these tube couplings at lower line pressures than other quick-disconnect couplings.

Use these fittings at pressures up to 9,700 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

A tapered needle gives you more precise control than standard flow-adjustment inline hydraulic valves.

Set your flow rate and then adjust it as necessary; these valves maintain flow rate despite pressure changes in the system.

Lock the handle using a padlock.

Also known as check valves, these open to allow flow in one direction and close when flow stops or reverses.

To set the pressure, unscrew the cap and turn the adjusting screw.

This hose is made of steel.