A drilled hole is required for installation. Screws can be removed repeatedly without affecting the anchor. To install, tap the anchor into the material until flush. Insert a screw and turn it to expand the anchor. For high volume tasks, use the optional installation tool—it doesn't require any twisting.

For technical drawings and 3-D models, click on a part number.

Easy to install, tap these anchors in like a nail—no drilled hole required. Two prongs under the flange prevent the anchors from turning inside the hole. Install anchors flush with the surface. Insert the screw and turn it to expand the anchor. Once installed, screws can be removed repeatedly without affecting the anchor. For high volume tasks, use our optional installation tool—it doesn't require any twisting.

For technical drawings and 3-D models, click on a part number.

A spring-loaded toggle holds against the back of the material. To install, insert the bolt through your fixture and thread the toggle onto it. Next, fold the toggle wings flush against the bolt and push them through a drilled hole until they pop open on the other side. Pull back on the bolt and tighten. Bolts are zinc-plated steel to resist corrosion in wet environments. The bolt is reusable, but the toggle will fall behind the wall when the bolt is removed. Extra toggles are sold separately.

For technical drawings and 3-D models, click on a part number.

For technical drawings and 3-D models, click on a part number.

Bolts are beveled under the head for use in countersunk holes. A spring-loaded toggle holds against the back of the material. To install, insert the bolt through your fixture and thread the toggle onto it. Next, fold the toggle wings flush against the bolt and push them through a drilled hole until they pop open on the other side. Pull back on the bolt and tighten. Bolts are zinc-plated steel to resist corrosion in wet environments. Bolts are reusable, but the toggle will fall behind the wall when the bolt is removed. Extra toggles are sold separately.

For technical drawings and 3-D models, click on a part number.

A shallow head makes these bolts good for low-clearance applications. The spring-loaded toggle holds against the back of the material. To install, insert the bolt through your fixture and thread the toggle onto it. Next, fold the toggle wings flush against the bolt and push them through a drilled hole until they pop open on the other side. Pull back on the bolt and tighten. They're zinc-plated steel to resist corrosion in wet environments. Bolts are reusable, but the toggle will fall behind the wall when the bolt is removed. Extra toggles are sold separately.

For technical drawings and 3-D models, click on a part number.

These toggle bolts speed installation by drilling their own pilot hole in 3/8"- 5/8" thick drywall. To install, drive the anchor into the wall. Then, position your fixture and insert the bolt into the anchor. The toggle is drawn against the wall as you tighten the bolt. Once set, the anchor will remain secure if the bolt is removed.

For holes that are larger than the screw head, use toggle bolts with washer. Often used for anchoring or mounting into existing holes, they can be used in any application where you would need a separate washer.

For technical drawings and 3-D models, click on a part number.

These toggle bolts speed installation by drilling their own pilot hole in 3/8"-5/8" thick drywall. To install, drive the anchor into the wall. Then, position your fixture and insert the bolt into the anchor. The toggle is drawn against the wall as you tighten the bolt. Once set, the anchor will remain secure if the bolt is removed.

For technical drawings and 3-D models, click on a part number.

These high-strength toggle anchors provide an extremely strong hold and stay in position when a bolt is removed. To install, push the toggle through a drilled hole and pull the anchor back toward you until the toggle rests flush against the wall. Then, slide the cap up to the wall and snap off the straps. Next, position your fixture, insert a screw and tighten. For use with machine screws; minimum screw length is the wall and fixture thicknesses plus 1/2".

Zinc-plated steel toggle anchors resist corrosion in wet environments.

18-8 stainless steel toggle anchors are chemical resistant and may be mildly magnetic.

For technical drawings and 3-D models, click on a part number.

These anchors fit a range of sheet metal and wood screw sizes since they form their own threads when installed. To install, fold the anchor in middle, insert into a hole, and tap flush. Thread a screw through your fixture and into the anchor. Extended length is the overall length of the anchor when folded in the middle.

For technical drawings and 3-D models, click on a part number.

These stud-style anchors include a nut and a washer. To install, push through a drilled hole; gravity drops the toggle into position. Anchors are removable and reusable. Made from zinc yellow-chromate plated steel, they resist corrosion in wet environments. Pull-out strength and shear strength values are 25% of the ultimate values.

For technical drawings and 3-D models, click on a part number.

A pivoting toggle bar creates a strong hold. These anchors provide an internally threaded socket connection for threaded rods and bolts. To install, push through a drilled hole; gravity drops the toggle into position. Anchors are removable and reusable. Made from zinc yellow-chromate plated steel, they resist corrosion in wet environments. Pull-out strength values are 25% of the ultimate values.

For technical drawings and 3-D models, click on a part number.

A wing-like toggle holds against the back of the material and spreads the force over a large area to hold 30 lbs. or more. The bolt is reusable, but the toggle will fall behind the wall when the bolt is removed. To install, insert the bolt through your fixture and thread the toggle onto it. Next, fold the toggle wings flush against the bolt and push them through a drilled hole until they pop open on the other side. Pull back on the bolt and tighten. Bolts are zinc-plated steel to resist corrosion in wet environments.