More sustainable than standard UHMW, these sheets and bars are made from partially recycled material, so they have a lower carbon footprint.

Made with carbon black, these recycled UHMW sheets are a sustainable alternative to standard UHMW sheets in applications where static electricity is a concern, such as in conveying equipment and chute liners.

Compared to our standard UHMW polyethylene, these sheets and bars hold up better to scuffs and scrapes in high-speed, high-precision, and high-impact applications—such as conveyor equipment, chute liners, and machine guards. Also known as Tivar HPV.

Also known as Tivar H.O.T., this material lasts up to 10 times longer in high-temperature applications than standard UHMW.

If a chip of this material breaks off, it can be located by metal detectors to reduce contamination risks.

This nylon 6/6 material is modified with MDS for a self-lubricating surface that’s more slippery than standard nylon. It's often used in high-friction applications, such as gears and bearings.

Because this 6/12 material absorbs less water than standard nylon 6/6, it holds its shape better. It’s often machined into hose fittings and valve components.

This nylon stays lubricated over time because it’s filled with oil. Use it to fabricate parts for hard-to-reach places where adding lubricants would be difficult.

Often used to make gears and wear strips, these cast nylon 6 sheets and bars withstand higher temperatures and are easier to machine than standard nylon 6/6 sheets and bars.

The addition of PTFE provides a more slippery, wear-resistant surface than standard Delrin® acetal resin. It’s commonly fabricated into pump components, gears, and bearings.

An economical alternative to Delrin® acetal resin, this acetal copolymer offers similar wear resistance.

Widely used in semiconductor applications, this polypropylene meets UL flame-retardance standards.

Known for its naturally slippery surface, PTFE surpasses most plastics when it comes to chemical resistance and performance in extreme temperatures.

This film is made with virgin Teflon® PTFE resins. It can handle extreme temperatures and resists most solvents.

This glass-filled PTFE is more rigid than standard PTFE for increased durability in high-stress applications.

Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.

These PEEK sheets can be machined to tight tolerances for use in electrical and semiconductor parts, such as test sockets.

Stronger than PTFE, PVDF offers good chemical resistance. Comparable to Kynar and Solef, it’s widely used for pump parts, tank liners, and seals.

Just as chemical resistant as PTFE, yet FEP offers greater impact strength. Use it to make valve components and gaskets.

With a diameter that’s held to a close tolerance, this material is hardened for increased wear and abrasion resistance.

Ready for turning in your lathe, these rods are precision ground to a tight tolerance.

Precision ground to a tight diameter tolerance, these rods are all set for turning applications in a lathe.

Often used for fasteners and valves, 410 stainless steel withstands wear caused by abrasion.

This material is hardened for increased wear resistance over standard 420 stainless steel.

Suitable for making molds, 420 stainless steel is a hard, wear-resistant material that can be finely polished to a very smooth surface.

These bars are precision ground on the top and bottom for a tight thickness tolerance of ±0.002".

These sheets have a softened temper, which is also known as annealed, so they can be easily formed into shape and then heat treated for spring properties.

The thickness on these bars is precision ground to a tight tolerance.

Made from powdered metal, M4 tool steel has a consistent microstructure that gives it outstanding resistance to wear and abrasion. It is comparable to CPM Rex M4.

Increase the life of rope slings by positioning these protectors over areas prone to wear.

Easily attach, move, and replace these magnetic wear strips on metal surfaces to minimize friction—simply press them on and peel them off as needed. Often found on conveyor systems and chutes, use these strips where friction between two parts or materials is wearing down equipment to extend equipment life.

With a thin metal backing, these sheets are good for use in bumpers, wear pads, machinery mounts, and other applications where some structural support is needed.

Use these sheets for a smooth stop.