Submerge these pumps to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

These pumps can be submerged or connected remotely to a pipe in your line. Magnets turn the impeller so there's no shaft seal to wear out. Use to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

Protected from impact by a durable epoxy-coated aluminum housing, these pumps can be submerged or connected remotely to a pipe in your line. Use to circulate water in small tanks, cooling baths, fountains, and other low-flow applications.

Circulate salt water in submerged and open-air applications.

Propel liquid higher and farther than standard circulation pumps. They're commonly used with chillers, heat exchangers, and boiler feed systems.

A powerful motor provides twice the flow rate of other extended-life circulation pumps. The motor is totally enclosed fan-cooled (TEFC) for use in dusty, dirty, and damp environments. Magnets turn the impeller to eliminate seal wear and leakage for a long service life. These pumps are often used with electroplating and photographic solutions.

The motor is totally enclosed fan-cooled (TEFC) for use in dusty, dirty, and damp environments. Use these pumps to move water and lubricating oil in boiler feed systems, cooling towers, and heat exchangers

These pumps can be used to move water and lubricating oil in boiler feed systems, cooling towers, and heat exchangers.

Propel liquid higher and farther than standard high-efficiency circulation pumps. These pumps use less electricity to achieve the same flow rates as other circulation pumps.

Instead of a fan-cooled motor, these pumps have an integrated motor that's cooled by the liquid being pumped for virtually silent operation and a long service life. Also known as canned motor pumps, they're commonly used in chiller systems and aquariums.

The motor is totally enclosed fan-cooled (TEFC) for use in dusty, dirty, and damp environments. Install these pumps up to 20 ft. above your liquid source to drain underground tanks and process wastewater.

A high-horsepower motor handles four times the flow and twice the pressure of other inline circulation pumps. Install these pumps directly in your pipeline for applications such as hot-water circulation and hydronic heating and cooling.

These pumps have higher flow rate than other inline circulation pumps and are cooled by the liquid being pumped to extend the life of the motor. Install them directly in your pipeline for applications such as hot-water circulation and solar heating.

A detachable motor assembly allows you to leave these pumps inline while servicing or repairing the motor. Install these pumps directly in your pipeline for applications such as hot-water circulation and hydronic heating and cooling.

A sealless construction means these pumps have few moving parts that can fail and shorten service life. The intake can be completely submerged in liquid.

Use when space is limited—these pumps connect to a pipe coming from your tank so you can place the pump in another location.

Also known as flexible impeller pumps, these create a suction force that can draw liquid upward to fill the pump chamber when your liquid source is below the pump.

Use these pumps to move higher volumes of water with solids than other sump pumps. They activate when plugged in; add a plug-in switch to control when the pump activates. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They are often used with liquid waste that has passed through a septic tank, so most solids are removed.

The float switch is wired to the pump. Also known as effluent pumps, these accommodate solids up to 3/4" in diameter. They're often used with liquid waste that has passed through a septic tank, so most solids are removed.

Use these pumps at temperatures up to 200° F. Also known as effluent pumps, they accommodate solids up to 3/4” in diameter. They’re often used with liquid waste that has passed through a septic tank, so most solids are removed. The float switch is adjustable and wired to the discharge pipe.

Pumps have a cast iron housing that stands up to demanding environments. The float switch is wired to the pump. Use with debris-free water.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Use with debris-free water.

The intake is 2" from the base of the pump to prevent dirt at the bottom of your sump pit from clogging the pump. Use with debris-free water.

These pumps have an explosion-proof motor that is rated for use where hazardous material is present. Since the motor is totally enclosed fan cooled (TEFC) and never comes into contact with the water, the pump can be used with hot water up to 300° F.

Convenient for applications where a sump pit is impractical, these pumps include a basin. Use with debris-free water.

An alarm and a red light alert you when water levels rise too high.

Remove water in locations without power with these battery-operated pumps.

This pump has a totally enclosed nonventilated (TENV) motor that is cooled by the liquid being pumped. Also known as a flexible impeller pump, it creates a suction force that can draw liquid upward to fill the pump chamber when your liquid source is below the pump.

Pumps have a powerful motor that provides more than twice the flow rate of standard water-removal pumps to quickly remove large volumes of liquid. They activate when plugged in; add a float switch to control when the pump activates.

Clean up water in flooded areas without a sump pit. Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates.

The switch activates on increasing pressure caused by rising water levels for a long service life. It has a separate cord, so you can replace the switch without replacing the whole pump. Use the handle to carry pumps from job to job.

Complete with a suction strainer and 6 feet of garden hose, these little pumps come ready to clean up small open spaces.

Built with high-chromium stainless steel components, these pumps stand up to salt water with up to 25% sand by volume and resist wear caused by abrasive particles. Fill the fuel tank with gasoline to remove water at sites without power.

With a polypropylene housing, these pumps are about half the weight of other gasoline-powered pumps. Fill the fuel tank with gasoline to remove water at sites without power.