Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Organize multiple lines of pipe, tubing, or hose with a single clamp. They are polyethylene for good chemical and UV resistance.

For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.

Backed with foam adhesive tape, these clamps mount to any smooth surface—no fasteners required. They are noncorrosive, nonconductive nylon.

Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.

For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.

Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

Load material between the two halves of the ring and adjust the side bolts for a tighter fit than standard threaded-rod-mount clamping hangers.

Lock your line in faster than any other hanger. These hangers automatically close when you press your line into the clamp.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.

Use these hangers in corrosive environments and where chemicals are present. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.

A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.

Mount these beams across parallel roof joists to hang threaded rod and route pipe, duct, and other overhead systems in areas where there’s no anchoring point.

For a strong, secure connection, mount these hangers by welding them to a rod.

Suspend and route flat-bottomed objects such as strut channel and small duct.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

Keep multiple bundles of wire and cable on separate hooks. The hooks have wide openings to allow access for installation, adjustment, and removal.

These plastic rings won't conduct electricity. Also known as distribution rings, they have a large opening for routing multiple cables. A smooth surface prevents damage to wire and cable.

Mount to a surface and add a cable tie to secure a bundle.

These mounts meet UL flammability requirements.

Attach these cable ties directly to a surface—no separate mount needed.

Keep an assortment of cable ties on hand.

The rounded, low-profile head keeps these ties from snagging and allows them to fit in tight spaces.

Pull the tab to tear off these cable ties.

Use these plastic cable ties when detection and retrieval are essential, such as in food processing applications. Ties are brightly colored for visibility and contain a special compound that can be picked up by X-ray equipment and metal detectors.

The head of these cable ties is contoured to fit against pipe, tubing, and other round material for a tight fit.

Secure and separate parallel bundles with the same tie.

These strong, wide ties are often used as an alternative to metal strapping.

Often used as tamper seals and in tagging applications, these ties create a consistent loop size every time.

With a thin, flexible body, these cable ties fit tightly around irregularly shaped bundles.

A foam padded back combined with an extra-wide body protects sensitive bundles, such as fiber optic cable.