Make a quick, secure wire connection without crimping.

Filled with silicone, these connectors seal out moisture and prevent corrosion.

Rated to 300° F, these connectors are an excellent choice for use in high-temperature applications such as HID lighting and electric heat.

Large enough to be used with a wide range of wire sizes, these connectors can still fit into cramped outlet boxes.

Soft molding over the wings provides a comfortable grip.

No wire stripping is required—these connectors will pierce the insulation.

Push stripped wires into connectors for a reliable connection that's faster to install than twisting or crimping.

These splices can withstand higher temperatures than insulated splices.

Visually confirm your connection through the inspection window in the insulation of these splices.

The most secure, electrically conductive, and environmentally sealed connection we offer, these splices have enclosed solder that melts when heat is applied.

Able to withstand temperatures up to 900°F, these splices are suitable for use in high-heat applications such as ovens, motors, and light fixtures.

Filled with grease, these splices resist moisture and corrosion.

When heat is applied, adhesive-lined insulation shrinks and bonds to the wires, creating a watertight seal.

These splices can withstand higher temperatures than insulated splices.

Insert wires and twist on the threaded end caps. The caps lock wires into place, making these splices a good choice for high-vibration applications.

With a ring of solder on the inside, these heat-shrink splices create secure, water-resistant connections between wires without the need for a crimping tool.

A plastic cover fully insulates these splices and it's clear so you can visually confirm the connection.

Join wires and cables in some of the dirtiest and wettest locations—from paper mills to marine environments—without special tools.

Pierce the insulation of wire without stripping it to make quick connections that are also sealed to keep out water.

Compress the barrel twice on each end for an extra-tight grip in high-vibration applications.

Tap and splice multiple wires in temporarily wet environments and up to six feet underground.

Use a single splice to connect more than two wires.

Filled with gel, these wire taps seal out moisture.

Tap a main wire or add a finished terminal to the end of a wire.

A plastic cover on the barrel provides electrical insulation.

The connection tab on these terminals is completely covered with insulation, leaving no metal exposed when mated.

The connection tab on these terminals is completely covered with insulation, leaving no metal exposed when mated.

Rated UL 94 V-0 for flame resistance, these terminals are made of flame-retardant, self-extinguishing material to reduce the risk of fire.

A plastic cover on the barrel provides electrical insulation rated to 600 volts.

The connection tab on these terminals is completely covered with insulation, leaving no metal exposed when mated.

These terminals withstand temperatures up to 900° F.

The connection tab on these terminals is completely covered with insulation, leaving no metal exposed when mated.

These terminals are connected to a single-conductor wire lead.

Mount these terminals on a threaded screw or stud for a more secure connection than spade and hook terminals.

Mount these elongated ring terminals on a range of screw sizes.

When heat is applied, the enclosed solder melts, creating the most secure, electrically conductive, and environmentally sealed connection we offer.

Choose from all-metal terminals rated to 900°F or 1200°F.

Thicker than standard ring terminals, these are more durable.

A plastic cover on the barrel provides electrical insulation rated to 600 volts.

Connect wire to a screw or stud at a right angle to fit connections into tight spaces.

Loosen your mounting screw to install—the open end eliminates the need to completely remove it.

When heat is applied, the enclosed solder melts and the insulation shrinks, creating the most secure, electrically conductive, and environmentally sealed connection we offer.

Connect wire to a screw or stud at a right angle to fit connections into tight spaces.

Add strength and stability to stranded wire to protect it from damage and speed insertion into terminal blocks.

Also known as bullet terminals, these have a round tab that requires less space than the flat tab found on most quick-disconnect terminals.

These solid pins make it easier to insert stranded wire into screw-clamp connections.

A hybrid of ring and spade terminals, these install without removing the mounting screw, yet resist being pulled off.

Turn screw and stud terminals into quick-disconnect connections.

Keep a variety of male/female pairs of quick-disconnect terminals on hand.

Keep a variety of ring terminal sizes on hand.

Compress the barrel twice for an extra-tight grip in high-vibration applications.

An offset tongue gives you extra space to insert wire.

Slide these lugs onto cable and strike them with your hammer to create a durable connection.

Thicker walls than standard battery terminal lugs make these more durable.

Insert your stripped cable into the compression nut and tighten; no crimping or heat is required.

Connect these clamps to cable with a crimping tool or by soldering.

Insert your stripped cable into the compression nut and tighten; no crimping or heat is required.

Made of lead, these clamps resist corrosion to stand up to marine environments. Use a lug to attach your cable to the stud.

Sets include a plug and socket with wire leads already installed, so they can be quickly added to existing wiring systems. They fit standard Molex plugs and sockets.

Connectors come assembled with wire leads already installed, so they can be quickly added to existing wiring systems. Use them with AMP MATE-N-LOK connectors.

Also known as power-pole connectors, these single-pole connectors join two pin connections, rather than a pin and socket. They stack from the top and sides to form any configuration.

Block signal interference from nearby devices, such as motors and transmitters, while maintaining a strong, stable connection for M12 threads.

Send power and signal to devices with M12 connections that are exposed to some of the toughest industrial stresses—from welding to metal machining and changing temperatures.

Plug these connectors into hazardous location devices. Using a NAMUR signal, they operate at a low current and voltage, so they prevent the risk of sparks and ignition in volatile areas.

To save space and reduce the number of cords in industrial automation setups, these splitters join two devices with M12 connectors to a single cord, distribution block, or I/O module with M12 connectors.

Send higher current than M5, M8, and M12 connectors near tough industrial jobs, such as welding and metal machining.

Also known as dummy plugs, these plugs close the electrical circuit on your mini connector, so you can safely change devices or repair connections.

Send higher current than M12 connectors to automated systems, motors, and pumps in environments where washdowns are common.

Reduce the number of cords needed to send and receive signals where space is tight.

Minimize signal loss between low-current devices with M8 connections.

Visually check that your low-current devices with M8 connections are powered up and sending and receiving signals. These connectors illuminate green if they have power and yellow if they have signal.