Sets include a plug and socket with wire leads already installed, so they can be quickly added to existing wiring systems. They fit standard Molex plugs and sockets.

Connectors come assembled with wire leads already installed, so they can be quickly added to existing wiring systems. Use them with AMP MATE-N-LOK connectors.

Stack as many connectors on top of each other as needed—the housings clamp together to form a secure attachment.

Block signal interference from nearby devices, such as motors and transmitters, while maintaining a strong, stable connection for M12 threads.

Send power and signal to devices with M12 connections that are exposed to some of the toughest industrial stresses—from welding to metal machining and changing temperatures.

Plug these connectors into hazardous location devices. Using a NAMUR signal, they operate at a low current and voltage, so they prevent the risk of sparks and ignition in volatile areas.

Visually confirm your connector is working properly. A green light means your connector has power, while yellow means it has signal.

Send higher current than M5, M8, and M12 connectors near tough industrial jobs, such as welding and metal machining.

Also known as dummy plugs, these plugs close the electrical circuit on your mini connector, so you can safely change devices or repair connections.

Send higher current than M12 connectors to automated systems, motors, and pumps in environments where washdowns are common.

Also known as pico connectors, these connectors are often used with 8 mm and smaller proximity switches and photoelectric switches.

Connect different pole configurations to join sensors, switches, and other devices to cords, distribution blocks, and I/O modules.

Send signal and power to low-current devices with M8 connections in food processing and other sanitary applications.

Visually check that your low-current devices with M8 connections are powered up and sending and receiving signals. These connectors illuminate green if they have power and yellow if they have signal.

Rated IP69K, these M16 connectors protect against dust, debris, and hot, high-pressure jets of water at high volumes.

Push these connectors together to quickly create signal and data connections in tight spaces. They need less space to mate than screw-together connectors, which require two hands to twist them in place.

Join M8 connections to M12 connections.

Build a connector that fits in tight spaces by combining male and female inserts for power and signal with a compact base and a hood.

Protect connections while maintaining access. The base and hood latch together securely yet can be quickly detached for equipment repair or replacement.

Often used with thermosensors or brakes on large motors, these carry more than twice the current of standard latching connectors.

Carry up to four times the current of standard Compact Latching Connectors. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement.

These connectors have the same pin and socket configuration as connectors that meet MIL-DTL-26482, so they can be used with products that meet the same standard. Quickly mate them by pushing them together.

These general purpose M23 connectors send power or signal to servomotors, servocontrollers, and servodrives.

With thick threads similar to a light bulb, these connectors take only a few turns to lock into place for a secure connection in washdown and high-vibration areas. Detach them just as quickly for frequent maintenance.

Make secure connections with machine tools, robots, and other equipment that vibrates frequently and carries currents as high as 300 amps.

Connect and disconnect your equipment all at once.

Unlike traditional RJ45 connectors found in data centers, these connectors stand up to rugged industrial environments since they tightly thread to devices with M12 connections, sealing out contaminants and resisting shaking loose from vibration. Use them to transfer high-speed data between sensors, switches, computers, IO modules, programmable logic controllers (PLCs), and other equipment.

FDA compliant for direct contact with food, these cords are safe to use with 12 mm proximity switches, valves, and power supplies in food, beverage, and pharmaceutical applications.

With a single cord, these splitters join two devices with M12 connectors to a distribution block or I/O module with M12 connectors. Often used with sensors and actuators, they send signals/power to your devices through one connection.

Send signal and power to low-current devices with M8 connections near welding, metal machining, and in spots where temperatures change.

These cords have a Nano M8 connector (also known as a pico connector) on one end and an USB Type-A connector on the other.

With a higher maximum current than nano M8 and micro M12 cords, these mini cords are often used with automated systems, motors, and pumps.

Connect multiple M8 and M12 cords to create a network between equipment. These blocks are often used to send signal and power to proximity switches and sensors.

Use these cords with hydraulic and air-powered valves, motors, pumps, and pressure switches. They have a solenoid valve socket on one end and an M12 threaded plug on the other.

Change the M8 8-pin connection on your Schunk gripper to wire leads for hardwiring robots that don’t have an M8 8-pin connection.

Connect your telephone to the wall jack.

Connect two telephone cords together to create a longer cord.