Mount these terminals on a threaded screw or stud for a more secure connection than spade and hook terminals.

Mount these elongated ring terminals on a range of screw sizes.

A plastic cover on the barrel provides electrical insulation. These terminals can withstand temperatures up to 300°F.

When heat is applied, the enclosed solder melts, creating the most secure, electrically conductive, and environmentally sealed connection we offer.

Thicker than standard ring terminals, these are more durable.

A serrated edge on the inside of the ring grips the mounting screw for a secure hold.

Save preparation time—these cords are ready-to-use with ring terminals on each end of a single-conductor wire.

Add strength and stability to stranded wire to protect it from damage and speed insertion into terminal blocks.

The connection tab on these terminals is completely covered with insulation, leaving no metal exposed when mated. They are rated to 600 volts.

The connection tab on these terminals is completely covered with insulation, leaving no metal exposed when mated.

The connection tab on these terminals is completely covered with insulation, leaving no metal exposed when mated.

Easy to install, connect, and disconnect, yet difficult to shake loose. These terminals interlock with each other to make a secure connection.

Rated UL 94 V-0 for flame resistance, these terminals are made of flame-retardant, self-extinguishing material to reduce the risk of fire.

Rated UL 94 V-0 for flame resistance, these terminals are made of flame-retardant, self-extinguishing material to reduce the risk of fire.

The connection tab on these terminals is completely covered with insulation, leaving no metal exposed when mated.

Loosen your mounting screw to install—the open end eliminates the need to completely remove it.

Apply heat to shrink the insulation and create a seal that keeps out water, salt, and contaminants.

Connect wire to a screw or stud at a right angle to fit connections into tight spaces.

These solid pins make it easier to insert stranded wire into screw-clamp connections.

Also known as bullet terminals, these have a round tab that requires less space than the flat tab found on most quick-disconnect terminals.

A hybrid of ring and spade terminals, these install without removing the mounting screw, yet resist being pulled off.

Turn screw and stud terminals into quick-disconnect connections.

Prevent accidental contact with other welding connections.

Slide these lugs onto cable and strike them with your hammer to create a durable connection.

Compress the barrel twice for an extra-tight grip in high-vibration applications.

An offset tongue gives you extra space to insert wire.

Twist stripped wires together, insert them into the connector, and then crimp for a dependable connection.

Press down on the clamp to connect wires and pull it up to disconnect.

Make a quick, secure wire connection without crimping.

Suitable for use in tight spaces, these connectors have a narrow profile that takes up less space than standard wire splicing connectors.

Filled with silicone, these connectors seal out moisture and prevent corrosion.

Soft molding over the wings provides a comfortable grip.

Large enough to be used with a wide range of wire sizes, these connectors can still fit into cramped outlet boxes.

The most secure, electrically conductive, and environmentally sealed connection we offer, these splices have enclosed solder that melts when heat is applied.

A plastic cover fully insulates these splices.

Crimp the barrel twice on each end for an extra-tight grip in high-vibration applications. A plastic cover fully insulates these splices.

These splices are filled with a sealant that creates a barrier to completely keep out moisture when splices are crimped.

Able to withstand temperatures up to 900°F, these splices are suitable for use in high-heat applications such as ovens, motors, and light fixtures.

These splices can withstand higher temperatures than insulated splices.

When heat is applied, adhesive-lined insulation shrinks and bonds to the wires, creating a watertight seal.

Sealed threads make these splices weather resistant.

With a ring of solder on the inside, these heat-shrink splices create secure, water-resistant connections between wires without the need for a crimping tool.

A plastic cover fully insulates these splices and it's clear so you can visually confirm the connection.

Make watertight connections for underground applications.

Pierce the insulation of wire without stripping it to make quick connections that are also sealed to keep out water.

Compress the barrel twice on each end for an extra-tight grip in high-vibration applications.

Tap and splice multiple wires in temporarily wet environments and up to six feet underground.

Use a single splice to connect more than two wires.

These wire taps meet UL 94 V-2 for flame retardance.

Tap a main wire or add a finished terminal to the end of a wire.

Use the included crimping tool to install a variety of terminals and butt splices.

Keep a variety of ring terminal sizes on hand.

Thicker walls than standard battery terminal lugs make these more durable.

When heat is applied, the flux and solder mixture creates a metallic bond that is nearly twice as strong as crimping or compression connections.

Connect these clamps to cable with a crimping tool or by soldering.

Made of lead, these clamps resist corrosion to stand up to marine environments. Use a lug to attach your cable to the stud.

Connect these clamps to a wide range of wire sizes.

A single row of terminals fits in narrow spaces.

Recessed screw terminals prevent you from accidentally connecting two circuits with a screwdriver or other tool, causing a short.

Best for equipment requiring regular servicing, these blocks disconnect without having to remove any wiring thanks to their plug-and-socket design. Their recessed screws prevent shorts by reducing the risk you’ll connect two circuits with a screwdriver or other tool.

Blocks mount in a cutout and have terminals on both sides.

Rated IP20, these blocks have recessed terminals to prevent accidental contact with live circuits.

Use with DIN 2 rail. Add as many circuits as you need with these terminal blocks and accessories.

One of the connections on these terminal blocks is a socket instead of a traditional terminal, making it easy to swap out equipment or change your wiring even in small enclosures. Instead of having to attach wire inside the tight space of your enclosure, you can wire a connector wherever it’s easiest and then plug it into the socket.

Inspect the terminal block and wiring without opening the cover.

Solder the pins on these blocks directly to your circuit board.

Protect connections against corrosion.These bars are tin-plated copper and have stainless steel terminals.

Stack multiple ring or spade terminals on the stud terminal; the current flows through the stacked terminals.

Use these connectors in vehicles and other agricultural and construction equipment. They have a sealed nylon housing that resists dust and temporary submersion.

Quickly replace or add connectors to an existing wiring system—connectors come assembled with wire leads already installed. Also known as weather-pack connectors, they withstand moisture, harsh engine fluids, and high temperatures.

Deliver power to welding cable. These connectors withstand the high temperatures and high current found in welding applications.

Block signal interference from nearby devices, such as motors and transmitters, while maintaining a strong, stable connection for M12 threads.

Often used to send power and signal to automated systems, motors, and pumps, these mini connectors carry higher currents than M5, M8, and M12 connectors.

Rated IP69K, these M16 connectors protect against dust, debris, and hot, high-pressure jets of water at high volumes.

Push these connectors together to quickly create signal and data connections in tight spaces. They need less space to mate than screw-together connectors, which require two hands to twist them in place.

Each set includes one male plug and one female socket that withstands the high temperatures and high current found in welding applications.

Use these connectors in general purpose residential and commercial applications.

Built to handle tough, repetitive-use applications, these are more durable than standard straight-blade connectors.

Check the status of a ground connection—a green light signals that connectors have power and are safely grounded.

Access the wire connection by opening the hinged housing. These connectors have screw terminals to create a secure connection; wire must be stripped before winding around the screw terminal.

Visually confirm that connectors have power; they have an indicating light that is visible from any angle.

Also known as hospital-grade connectors, these have an extra-tight fit when mated to remain secure in high-vibration environments.

Stainless steel hardware and nickel-plated blades or slots protect connections from damage in corrosive environments.

Visually confirm that sockets have power—the face lights up when they're connected. The rubber housing protects them from damage caused by drops and other impact.

Rated NEMA 6P and 13, IP66, and IP69K when mated, connectors withstand oil/coolant spraying, high-pressure, high-temperature washdowns, and are corrosion resistant so they can be used in marine environments.

Eliminate the need for wire stripping; snap-on terminals pierce the wire insulation. When mated with a receptacle, these plugs have an extra-tight fit to withstand high vibration. Also known as hospital grade plugs.

Configure a connector for your application—combine housings with pins and sleeves for different wire sizes. They fit AMP MATE-N-LOK connectors.

Stack as many connectors on top of each other as needed—the housings clamp together to form a secure attachment.

A sealed housing protects connectors from weather. Sets include a plug and socket with wire leads already installed. They fit standard Molex connectors.

Sets include a plug and socket with wire leads already installed, so they can be quickly added to existing wiring systems. They fit standard Molex plugs and sockets.

Also known as power-pole connectors, these single-pole connectors join two pin connections, rather than a pin and socket. They stack from the top and sides to form any configuration.

Check the status of a ground connection—a green light signals that connectors have power and are safely grounded. They turn to lock together when mated to prevent accidental disconnection.

Configure a connector for your application—combine housings with pins and sleeves for different wire sizes. Use them with standard Molex connectors.

When mated, these connectors meet NEMA 6P for protection against washdowns and temporary submersion.

These general purpose M23 connectors send power or signal to servomotors, servocontrollers, and servodrives.

Assemble a connector that can handle multiple applications at once. Combine inserts that send power, signal, and data with a base and a hood.

Configure a connector for your application—combine inserts for power and signal with a base and a hood.

The smallest latching connectors we offer, these fit in tight spaces. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement.

Protect connections while maintaining access. The base and hood latch together securely yet can be quickly detached for equipment repair or replacement.

Often used with thermosensors or brakes on large motors, these carry more than twice the current of standard latching connectors.

These connectors meet international standards IEC 309-1 and 309-2. They prevent an electrical arc when separating mated connectors, so you can safely connect and disconnect with the power on.

Reduce the likelihood of slips and falls in high-traffic areas—connectors won't roll when stepped on.

Make secure connections with machine tools, robots, and other equipment that vibrates frequently and carries currents as high as 300 amps.

These connectors meet MIL-DTL-26482, so they're compatible with other products that meet the same standard. Quickly mate by pushing them together.

These connectors have the same pin and socket configuration as connectors that meet MIL-DTL-26482, so they can be used with products that meet the same standard. Quickly mate them by pushing them together.

Power hydraulic and air-powered valves, motors, pumps, and pressure switches.

One hand is all you need—just push these connectors in to secure them and charge surveillance cameras, user interfaces, and other small devices.

Reduce the number of electrical connections in sanitary areas, such as food plants—these connectors combine Ethernet, a power cable, and wire for signals into a single connection point.