Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

These grips are made of nylon, which resists most chemicals. The nylon mesh extension provides a secure hold when the cable is pulled or in motion.

Tighten the screw-down clamp for superior pull-out resistance.

These grips have an extension that provides extra support for moving cable and prevents kinking for longer cable life.

A rubber bushing with an oval slot provides liquid-tight entry for building cable, which is also known as Romex type NM-B or type UF-B.

These cord grips are lightweight yet durable.

The mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Made of nylon, these grips resist chemicals.

These grips have an extension that provides extra support for moving cables and prevents kinking for longer cable life.

Tighten the screws to secure your cable.

Connect a single flat cable to a junction box.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These 90° elbows meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Peel away layers of rubber inserts to fit around cord grips, even when you don't know the exact diameter.

FDA compliant for direct food contact, these cord grips have a multi-piece design to wrap around cables in sanitary environments without removing connectors or rewiring.

Install additional cables without swapping cord grips by pushing them through the thin, flexible seals on these grips, which have a sanitary design suitable for food-processing and pharmaceutical plants.

These fittings seal out liquids when connecting liquid-tight flexible metal conduit to a knockout in an outlet box or enclosure.

Join pieces of conduit.

The spiral design makes this conduit more flexible than abrasion-resistant liquid-tight flexible plastic conduit.

The toughest liquid-tight flexible metal conduit we offer, this resists oil, chemicals, and extreme temperature fluctuations.

In addition to resisting oil, this conduit resists lubricants and grease.

Attach conduit to a knockout in an outlet box or enclosure.

Visually identify different runs of wire and cable in machine and equipment wiring.

Make tight bends in machine and equipment wiring.

Also known as antishort bushings, these grommets slide into the ends of conduit and armored cable to protect wire and cable from sharp edges.

Attach conduit to a knockout in an outlet box or enclosure.

Attach conduit to a knockout in an outlet box or enclosure.

Attach conduit and armored cable to a knockout in an outlet box or enclosure.

Covered with a copper braid, this conduit protects wire and cable from electromagnetic interference (EMI) caused by motors and other equipment.

Attach conduit to a knockout in an outlet box or enclosure.

Join different sizes of conduit.

Reduce the knockout size in an outlet box or enclosure so you can attach a different size of conduit to it.

Seal out moisture while reducing the knockout size in an outlet box or enclosure so you can attach a different size of conduit to it.

Also known as conduit bodies, these ports provide access to wire and cable inside PVC conduit for pulling, splicing, and maintenance. They are also used to change the direction of a run.

Join pieces of conduit.

Use in food-processing and chemical plants—this is the most corrosion resistant thick-wall conduit we offer.

Also known as conduit bodies, these ports provide access to wire and cable inside thick-wall (rigid) metal conduit for pulling, splicing, and maintenance. They are also used to change the direction of a run.

Join pieces of conduit.

Connect different sizes of conduit.

Join pieces of conduit.

Attach conduit to a knockout in an outlet box or enclosure.

Join pieces of conduit.

Connect different sizes of conduit.

The most corrosion-resistant thin-wall conduit we offer, use this along walls and ceilings in food-processing and chemical plants.

Attach conduit to a knockout in an outlet box or enclosure.

These fittings seal out liquid when used with continuous-flex liquid-tight plastic conduit.

In addition to continuous-motion applications such as robotics, this conduit is suitable for high-vibration applications.

Secure threaded plastic conduit fittings to a knockout in an outlet box or enclosure.

Transition between types of conduit.

A hinged cover allows easy access to your wire and cable. It also keeps the sidewalls secure, so this duct is sturdier than duct with a snap-on cover.

Narrower slots and fingers create more access and routing points than on standard slotted wire duct.

A hinged cover allows easy access to your wire and cable. It also keeps the sidewalls secure, so this duct is sturdier than duct with a snap-on cover.

With a top that overhangs the cover, this raceway keeps out rain. It is rated NEMA 3R for protection from liquids and light splashing.

Route power, data, and control cable rated up to 600 volts AC/DC.

Insert and remove cable at any point along the length of this open-top, hook-shaped raceway.

With more than one channel, this raceway allows you to separate power and data wiring to prevent signal interference.

Surface mount with the adhesive back to route low-voltage data and control cable where you can't get inside walls.

Cut, bend, and connect these wire mesh tray systems to route cable and hose in configurations such as curves, slopes, and tees.

Create a system to route cable and hose by connecting components such as straight trays and tees.