Racks have multiple hooks to hang items

Adhesive strips hold tight yet remove cleanly without damaging the wall.

Quickly mount these hooks with a few strikes of a hammer.

Attach these general purpose hooks to steel walls, cabinets, and other magnetic surfaces.

A locking tab and mounting screw secure hooks on hardboard pegboard to hang wrenches, handsaws, levels, and other tools.

Hang wrenches, handsaws, levels, and other tools on these hooks.

Assortments include enough pieces to set up an entire pegboard.

Slide caps onto the end of hooks to protect items from scratches.

These hooks meet MS-87006.

For extra security, these have a latch that snaps back into place to secure your load.These have excellent resistance to salt water and chemicals.

One side is closed and the other is open.

A latch ensures rope, chain, and fittings won't separate from the hook when the load slackens. The hook opening accommodates large anchor points and allows chain to move freely through the closed hook.

These rotate for easy positioning before a load is applied. They have a latch to ensure rope, chain, and fittings won't separate from the hook when the load slackens.

These have a removable half-link to attach large rings, links, and other closed fittings.

These have a latch that locks closed when a load is applied for a more secure connection than standard hooks. They rotate for easy positioning before a load is applied.

For a more secure connection than standard hooks, these clevis hooks have a latch that locks closed when a load is applied.

A ball-bearing swivel allows these to rotate under load. Attach to chain by inserting the included pin through a link.

These rotate for easy positioning before a load is applied.

Pop the clevis pin in to install these hooks, no extra fittings needed.

Also known as foundry hooks, use these on thick molds, castings, and objects that don't have attachment points.

Easily slip chain, rope, and fittings on and off these open-mouth hooks. Attach your chain to the eye end.

Weld these hooks into place.

The latch ensures rope, chain, and fittings won't separate from the hook when the load slackens.

These snaps have an eye that rotates for easy positioning.

Lock the bolt with wire or a cable tie for a secure connection.

A wide opening accepts large diameters of rope and pipe. Squeeze the trigger to release.

Flat sides allow webbing and strapping to lay flat, so they won't slide and bunch.

Use for three-sided connections. Flat sides ensure webbing and strapping lay flat, so they won't slide and bunch.

A lock slides upward over the latch to lock. The latch opens outward to accept large diameters of rope.

Pull the collar to release the shackle from its locked position.

Attach a rope to the ring on the pin for remote release where access in limited. These shackes have a clevis end for making pivoting connections.

The galvanized finish resists corrosion.

Permanently sew webbing onto these hooks.

Keep multiple bundles of wire and cable on separate hooks. The hooks have wide openings to allow access for installation, adjustment, and removal.

Hang cable and other flexible material beneath wire to prevent it from sagging and swaying. To install, hook the two ends of the ring around the wire—no fasteners required.

Use these tools to hold, separate, and position wire, springs, and other small parts.

A different tip at each end allows you to install, extract, and position parts with one tool.

The handle has a magnet at the end to pick up small steel objects. Use these picks to hold and position wire, springs, and other small parts.

The handles of these assorted picks have a magnet at the end to pick up small steel objects. Use to hold and position wire, springs, and other small parts.

Solder won’t stick to these assorted picks, which are used for positioning circuit board components.

Made of beryllium copper that is FM approved, these picks satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These assorted picks have insulated handles that protect against accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

The assorted picks in these sets are used to install and position tiny springs and wires. Unlike conventional picks that have pointed tips, these are rounded to prevent damage to sensitive components.

A different tip at each end installs and positions tiny springs and wires. Unlike conventional picks that have pointed tips, these are rounded to prevent damage to sensitive components.

Use the assorted tools in these sets to pull material out of tight spots. The corkscrew tips twist into material for a firm hold while the handle provides the necessary leverage for pulling.

Shaped for removing the seals around bearings, insert the tip of these tools behind the seal and pull. The curved head provides leverage to remove stuck and stubborn material.

Made of beryllium copper with an aluminum-bronze handle, these pullers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Use to extract material from tight spots.

Also known as packing irons, the offset handle allows you to install packing into hard-to-reach areas while the blunt tip prevents accidentally cutting or damaging the packing material.

Sets include an assortment of handles and tips for pulling material out of tight spots. Replace tips when they become worn or to use a different style.