This sleeving withstands temperatures up to 390°F and is often used to insulate connections in transformers and relays. It prevents electricity and heat from dissipating from wire and cable.

Add a layer of insulation to prevent electricity and heat from dissipating from wire and cable.

Made from thicker and denser fiberglass than standard spark-resistant sleeving, this sleeving is more abrasion resistant and provides better insulation. The silicone rubber coating protects against sparks and molten metal splash.

This sleeving withstands temperatures over 1000°F, such as in refineries.

With a temperature rating of 1800°F or higher, this sleeving can withstand hotter temperatures than fiberglass and most ceramic.

Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.

Protect cable, hose, and pipe in high temperature environments—this sleeving withstands temperatures over 450° F. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Use this braided copper sleeving to protect wire and cable from signal distortion caused by nearby equipment and devices. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Tested to meet MIL-STD-202, this sleeving meets performance standards for flame retardance. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Rated UL 2024 and NFPA 262, this sleeving is approved for use in plenum spaces such as duct work and above a drop ceiling. It self-extinguishes and emits minimal amounts of smoke and gas during combustion. Stretch to fit over items for easy installation; it tightens around its contents for a secure fit.

Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390°F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.

Snaps keep this sleeving securely closed, yet permit quick access to contents and allow you to route wires in between the snaps. Use it to easily wrap around wire, cable, and hose without disconnecting them.

Use this shielded sleeving to protect wire and cable from signal distortion caused by nearby equipment and devices. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

Zip this sleeving around wire, cable, or hose that are connected at both ends to quickly bundle them.

Unlike traditional sleeving that bunches wire and cable into a circle, this sleeving holds them flat, so it’s good for tight spaces such as vehicle interiors. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

Coated with PVC, this polyester sleeving resists chemicals and solvents. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

A slit along the length makes this sleeving easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.

Made of nylon, this sleeving is the most impact- and abrasion-resistant slit corrugated sleeving we offer. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them.

This sleeving reflects heat away from contents and withstands temperatures up to 900°F. The corrugated construction gives it impact and abrasion resistance similar to conduit, but with more flexibility.

The two halves of this sleeving nest into each other, fully enclosing contents. It has interlocking ridges that overlap to keep out dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

A mica and silicone rubber blend allows this sleeving to withstand temperatures up to 2100° F. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.

Wrap this sleeving around cable, cords and wires to protect them and to form bundles.

Made with a self-extinguishing additive, this sleeving will not produce fumes when exposed to open flame or high temperatures. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Use this general purpose tubing to insulate and protect wire and cable.

Access connections more easily than with standard heat-shrink tubing. Make a small slit in this tubing to peel it away.

This tubing creates a tight seal over irregularly shaped objects.

Extra-thick walls provide better protection against abrasion and tears than standard moisture-seal tubing, as well as creating a water-resistant seal.

Create a water-resistant seal—this tubing has an adhesive lining that melts when the tubing is heated and bonds to the underlying surface.

Use this tubing in applications where temperatures reach up to 500° F. It's often used to insulate electronic components.

This tubing shrinks down to a quarter of its original ID, so it creates a tight seal over irregularly shaped objects. It withstands up to 500° F.

Made of woven polyolefin/polyester fabric, this tubing has excellent abrasion resistance so it can be dragged over rough surfaces without damage.

Made of PVDF, this tubing has excellent cut and abrasion resistance. It has a flame-retardant additive that resists combustion and minimizes the spread of flames.

With excellent resistance to tears and cuts, this tubing withstands demanding use.

A layer of conductive cloth protects wire and cable from signal interference caused by nearby equipment and devices.

Resistant to diesel fuel, hydraulic fluid, and lubricating oil, this tubing is often used in vehicles.

Use this tubing where wire and cable may be exposed to chemicals, oil, and acids.

Maintain a supply of tubing in a variety of sizes that withstand abrasion, moisture, and chemicals.

A different shrink ratio on each end allows this tubing to fit over cable assemblies and wire harnesses with large connections, or around connectors with a 90° elbow.

Also known as breakout boots, these splitters insulate and seal the point where wire splits off from cable, or where cables exit from conduit.

Seal the end of crimped connections, such as motor coils, to protect them from moisture.

Apply this liquid for a skin-tight protective coating that insulates and resists moisture, acids, and corrosion.

Also known as mastic tape, this tape is thicker than other electrical tape to cushion, insulate, and seal out moisture and environmental contaminants in electrical connections.

Insulate wire and cable splices, wrap wire harnesses, and repair cable jacketing with this stretchy tape.

At only 0.0025" thick, this tape combines conformability with durability and abrasion resistance.

This traditional black cotton electrician's tape provides an abrasion-resistant shield for wrapping low-voltage splices.

This chemical-resistant tape has adhesive on both sides.

This puncture- and cut-resistant cotton tape is coated with a high-grade electrical-insulating varnish. Also known as cambric tape.

The adhesive on this conformable aluminum foil tape is electrically conductive for use on surfaces that can't be soldered. Use it to shield cables and electronic components from EMI (electromagnetic interference).

Made of polyester fabric with a copper/nickel filler, this tape is highly conductive throughout, including the adhesive.

Twice as thick as our standard antistatic electrical tape, this tape is made of abrasion-resistant aramid and antistatic PTFE.

Use this tape to wrap and splice cables, mask components while soldering, or as a 3D printing surface.

Shield against extreme heat with these flexible ceramic strips. They are often used to insulate hose, cables, and process piping.

Stronger than Garolite CE with better electrical-insulating properties, Garolite XX is often fabricated into low-cost electrical components.

Stronger than Garolite CE with better electrical-insulating properties, Garolite XX is often fabricated into low-cost electrical components.

Frequently called electrical-grade Garolite, this Garolite G-9 is strong, electrically insulating, and arc resistant in dry environments.

Resisting heavy impacts and temperatures up to 500° F, these Garolite sheets are used in machinery such as turbine bearings and downpipe gaskets.

Often used for terminal boards, electrical housings, end plates, and structural components in high temperatures, these sheets are a flame-retardant version of Garolite G-11. All are stronger and resist heat better than Garolite G-10/FR4.

Choose these Garolite G-7 rods for their high heat tolerance—they withstand temperatures up to 425° F. While not as strong as Garolite G-9, they offer better arc resistance in dry environments.

More electrically insulating than Garolite XX, these tubes are often machined into insulating washers, bushings, transformer spacers, and parts of terminal boards.

Offering excellent arc and track resistance, this GPO3 fiberglass is often used for electrical applications in humid environments.

Offering excellent arc and track resistance, this GPO3 fiberglass is often used for electrical applications in humid environments.

Offering excellent arc and track resistance, this GPO3 fiberglass is often used for electrical applications in humid environments.

Hard fiber is the easiest composite to machine, making it good for creating custom parts. Also known as vulcanized fiber.

Package food, textiles, and other products in wet environments. This film won’t absorb or swell from water.

Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.

Protect the cables on your TIG guns from weld spatter.

Cut with scissors or a utility knife to cover irregularly shaped electrical hazards.