Pull one or more cables through conduit.

Made of fiberglass with a plastic tip, this tape is safer to use around energized equipment than metal fish tape.

Use this flat tape for long runs without bends. Choose from steel or stainless steel.

Thicker than standard fish tape, this fiberglass tape remains stiff along its entire length for long runs of conduit and raceway. It’s nonconductive, so it’s safer to use around energized equipment than metal fish tape.

As you pull with both hands, a latch grabs onto fish tape or pulling rope. Unlike pliers, this puller will not kink or slip off the fish tape.

Route wire and cable outside of conduit in drop ceilings and behind walls. Made of nonconductive fiberglass, these rods are safer to use around energized equipment than metal rods.

With a handle and mounting hook for portability, these winches can move from job to job.

Remove the handle to wind these winches with a power drill.

One-piece gears provide more durability than the riveted gears of other hand winches. These winches move loads more gradually than standard hand winches. They take longer to wind but require less effort.

Remove the handle to wind these winches with a power drill and move loads more gradually than with other winches. The one-piece machined gears stand up to daily use.

Tackle frequent lifting jobs with these rugged winches—their one-piece machined gears stand up to daily use.

Move loads more gradually than with other winches. These take longer to wind but require less effort. Their one-piece machined gears stand up to daily use.

An automatic brake holds the load, even when power is lost.

Because these winches run on compressed air, they give you longer operating times than electric winches.

These pullers unwind four times faster than other pullers. Pullers provide the capacity of a winch in a versatile, portable tool. They have wire rope which is stronger than rope and webbing but not as bulky as chain.

These versatile pullers give you the capacity of a winch, and have a thick, rugged frame for long life. The wire rope on the pullers is stronger than rope and webbing but not as bulky as chain.

When there isn't clearance to use standard-grip pliers, the angled head on these tools gives you access. Also known as lineman’s and combination pliers, use them to pull, bend, and cut wire.

Also known as lineman’s and combination pliers, use these tools to pull, bend, and cut wire.

Additional features, such as wire terminal crimpers, enable you to perform a variety of electrical wiring and installation work with a single tool. Also known as lineman’s pliers, use them to pull, bend, and cut wire.

Avoid the potential for an arc flash or short circuit that can occur when using conventional insulated tools with metal components. Completely metal-free, these pliers are plastic with ceramic cutting blades. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. Use to pull, bend, and cut wire.

Made of aluminum-bronze that is FM approved, these pliers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Use them to pull, bend, and cut wire.

These assorted picks have insulated handles that protect against accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Use these tools to hold, separate, and position wire, springs, and other small parts.

Reach around obstructions and into tight spaces with picks that have long, angled tips. Use these tools to hold, separate, and position wire, springs, and other small parts.

The handle has a magnet at the end to pick up small steel objects. Use these picks to hold and position wire, springs, and other small parts.

A different tip at each end allows you to install, extract, and position parts with one tool.

Change tips to use a different size or style pick for holding and positioning wire, springs, and other small parts.

Solder won’t stick to these assorted picks, which are used for positioning circuit board components.

Made of beryllium copper that is FM approved, these picks satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

A different tip at each end installs and positions tiny springs and wires. Unlike conventional picks that have pointed tips, these are rounded to prevent damage to sensitive components.

The assorted needle-sharp picks in these sets are similar to dental instruments and suitable for work around delicate circuits and components.