Surface mount with the adhesive back to route low-voltage data and control cable where you can't get inside walls.

Insert and remove cable at any point along the length of this open-top, hook-shaped raceway.

This raceway system is also known as wireway and wire trough.

In areas exposed to washdowns, chemicals, and corrosion, install this stainless steel raceway system that has gaskets at the connection points.

Protect wire and cable from dust, dirt, and oil/coolant dripping—this raceway is rated NEMA 12.

Faster to install than standard slotted wire duct, attach this to flat, clean surfaces.

Route wire and cable around curves with this bendable wire duct.

Use in areas with light pedestrian traffic.

Lay your cable in the slit on the top so it stays off the floor.

Protect cable from carts, pedestrians, and other light indoor traffic.

With the widest channels of any of our cable ramps, these ramps can span large cable, hose, and pipe.

Thicker corrugations make this conduit more crush resistant than standard flexible plastic conduit.

Connect different sizes of conduit.

Attach conduit to a knockout in an outlet box or enclosure.

Join pieces of conduit.

Also known as antishort bushings, these grommets slide into the ends of conduit and armored cable to protect wire and cable from sharp edges.

Join pieces of conduit.

Attach conduit to a knockout in an outlet box or enclosure.

Join pieces of conduit.

Also known as Type B, this conduit is more crush and abrasion resistant than liquid-tight flexible plastic conduit.

In addition to resisting oil, this conduit resists lubricants and grease.

These fittings seal out liquids when connecting liquid-tight flexible metal conduit to a knockout in an outlet box or enclosure.

Even in temperatures as low as -50° F and as high as 220° F, this conduit stays flexible.

Covered with a copper braid, this conduit protects wire and cable from electromagnetic interference (EMI) caused by motors and other equipment.

Join pieces of conduit.

Connect to the end of conduit or a fitting to protect wires from abrasion when being pulled.

Ground conduit by running a ground wire through the attached lug.

This impact- and crush-resistant conduit is also known as galvanized rigid conduit (GRC).

Also known as conduit bodies, these ports provide access to wire and cable inside PVC conduit for pulling, splicing, and maintenance. They are also used to change the direction of a run.

Attach conduit to a knockout in an outlet box or enclosure.

Connect different sizes of conduit.

Attach conduit to a knockout in an outlet box or enclosure.

Join pieces of conduit.

Attach conduit to a knockout in an outlet box or enclosure.

This nonmagnetic aluminum conduit withstands damp and corrosive environments.

Attach conduit to a knockout in an outlet box or enclosure.

Connect different sizes of conduit.

Attach conduit to a knockout in an outlet box or enclosure.

Visually identify different runs of wire and cable along walls and ceilings with this conduit that has a painted exterior.

Attach conduit to a knockout in an outlet box or enclosure.

One end twists into a piece of conduit for a quick connection; the other end attaches to a knockout in an outlet box or enclosure.

Also known as Type A, this conduit meets the demands of continuous motion while sealing out liquid when used with liquid-tight fittings.

Transition between types of conduit.

Secure threaded metal conduit fittings to a knockout in an outlet box or enclosure.

These are the most corrosion-resistant tray systems we offer.

Create a system to route cable and hose by connecting components such as straight trays and tees.

The hinged snap-on crossbars open for access at any point along the carrier's length so you can lay in the cable and hose, rather than threading it through.

A more durable construction with a zinc-plated steel frame provides strength for a longer service life than other open cable and hose carriers.

Bending and twisting up to 380° in any direction, these carriers organize and protect cable and hose around machines that are constantly moving, such as robotic arms and conveyors.

A strip of hook-and-loop creates a strong seal along the entire length of this sleeving, yet it can be opened at any point to access contents. Use it to wrap around wire, cable, or hose without disconnecting them.

Wrap this sleeving around wire, cable, and hose without disconnecting them. It has a slit along the entire length and wraps over itself to stay closed without an adhesive strip or other closure.

Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390°F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.

Unlike traditional sleeving that bunches wire and cable into a circle, this sleeving holds them flat, so it’s good for tight spaces such as vehicle interiors. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

Often used to protect wire, cable, and hose in robotics and other automated applications, this highly flexible sleeving withstands continuous motion without tearing or fraying.

The tightly braided construction makes this polyester sleeving abrasion resistant. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Rated UL 94 V-2, this sleeving resists combustion and minimizes the spread of flames. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. It has impact and abrasion resistance similar to conduit, with more flexibility.

The corrugated construction gives this sleeving impact and abrasion resistance similar to conduit, but with more flexibility.

This sleeving reflects heat away from contents and withstands temperatures up to 300°F. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.

A slit along the length makes this sleeving easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.

This sleeving absorbs UV light, so it can be used in direct sunlight without getting damaged. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Protect cables, cords, and wire and form them into bundles in your food-processing plant while lowering the risk of contaminating the food.

A mica and silicone rubber blend allows this sleeving to withstand temperatures up to 2100° F. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.

Made of PVC, this sleeving resists chemicals, oil, and acids.

A specially formulated silicone rubber coating allows this sleeving to stretch over items during installation; it then tightens around its contents for a secure fit.

This sleeving withstands temperatures up to 390°F and is often used to insulate connections in transformers and relays. It prevents electricity and heat from dissipating from wire and cable.