These cord grips are lightweight yet durable.

Secure and seal electrical cords entering knockouts at a 45° angle.

These grips install into enclosure holes quickly to stabilize and relieve strain on cords.

Made of nylon, these grips resist chemicals.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Tighten the screws to secure your cable.

An insert clamps the cable in place to provide more strain relief than other snap-in cord grips for building cable.

Able to withstand temperatures up to 300° F, these grips are also corrosion- and chemical-resistant.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.

Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

Secure cords in washdown areas where there’s minimal space—these cord grips curve 90° to relieve stress from bending.

Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.

These grips have an extension that provides extra support for moving cable and prevents kinking for longer cable life.

Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation.

Create a tight grip on cords in wet environments while reducing stress from bending—the 90° angle of these cord grips routes cords to fit tight spaces in enclosures and panels.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

Keep your cord at a gentle angle without sacrificing a tight hold, even in tough, wet environments.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

Also known as cable-entry seals, the cable-entry side has heat-shrinkable polyolefin with an adhesive lining.

Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress.

The mesh offers a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

Modify these cord grips to get the right fit for your cord even when you don't know the exact diameter.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

FDA compliant for direct food contact, these cord grips have a multi-piece design to wrap around cables in sanitary environments without removing connectors or rewiring.

Secure multiple flat cable through one cord grip—reducing the space and number you need for a project, as well as saving time.

The face of these grips is flush with the cable-entry point for a seamless appearance.

These grips are galvanized steel for good corrosion resistance.

These are tin-plated bronze.

These are tin-plated bronze.

A spring extension prevents sharp bends and kinks in your cord, prolonging its life. These bushings, which are more rigid than grommets, shield cords from rubbing against the edges of holes in enclosures and panels, so they won’t wear down.

These mounts meet UL flammability requirements.

Often used to secure vertical running material, these mounts maintain space between a bundle and a surface.

For use in environments subjected to chemicals, these mounts withstand the most corrosive conditions.

Handle high production jobs with minimal effort. Multiple tension settings ensure a precise fit around the bundle.

Reduce gaps between the cable tie and bundle—these ties have a smooth body that allows them to adjust to the exact size of the material.

A foam padded back combined with an extra-wide body protects sensitive bundles, such as fiber optic cable.

These ties are less likely to crack and break from dryness than regular cable ties.

Use the built-in blade to remove excess length once these ties are secure.

Use these plastic cable ties when detection and retrieval are essential, such as in food processing applications. Ties are brightly colored for visibility and contain a special compound that can be picked up by X-ray equipment and metal detectors.

The tail slots into the head to create a temporary loop to hold wires. Hook and unhook the loop to add additional wires before permanently cinching the tie.

The head of these cable ties is contoured to fit against pipe, tubing, and other round material for a tight fit.

Secure and separate parallel bundles with the same tie.

These strong, wide ties are often used as an alternative to metal strapping.

Often used as tamper seals and in tagging applications, these ties create a consistent loop size every time.

With a thin, flexible body, these cable ties fit tightly around irregularly shaped bundles.

A foam padded back combined with an extra-wide body protects sensitive bundles, such as fiber optic cable.

Take the guesswork out of identifying material—use the attached tag to label the bundle.

Create custom-length cable ties for large bundles and heavy materials.

Attach with a screw or other fastener.

Stick these ties to any smooth, clean surface.

These ties meet UL flammability requirements.

Take the guesswork out of identifying material—use the attached tag to label the bundle.

Create a cable tie with a buckle—no sewing required.

Woven from flexible stainless steel yarn and Nomex, these ties handle temperatures up to 850° F.

The buckle allows you to cinch these ties tight.

These ties stretch to hold material tightly without slipping.

These ties are flexible, reusable, and adjustable for delicate bundles or bundles that frequently change in size.

These cable ties are easy to yank apart or cinch shut, even when wearing gloves—a textured tab on the end gives you a good grip.

Easily transport or hang cords, rope, and hose—these hook and loop cable ties include a handle.

The hook and loop on these ties holds more tightly than other hook and loop.

Add push-in cable holder to this adapter to mount cable to DIN rail.

Keep individual wires separate by laying them between the coils on these holders.

Mount to a surface to secure and route cable.

These stretchy ties conform to irregularly shaped bundles to grip material tightly.

The softest of our twist ties, they have a cushioned outer layer for bundling delicate materials.

Formed to the shape of a round bundle, these ties close with a single twist of the top.

Secure large bundles such as lumber, cardboard, and wire coils.

Bundle, close, and label bags and sacks.

Ties come on a spool for use in a twist tie machine.