Install these clevis-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Use a new plug when installing a fitting on a different rope.

Place the wire rope and sleeve through a hole in the assembly block and tighten into a vise to hold. Then attach the plug driver on the end of a plug to make hammering in the plug easier.

Also known as socket-end swage fittings, install these eye-end fittings with a roller swage press for a strong, permanent hold.

Also known as socket-end swage fittings, install these clevis-end fittings with a roller swage press for a strong, permanent hold.

Add a stud end to wire rope without having to fray the rope or use a compression tool.

Add a mounting-plate to wire rope without having to fray the rope or use a compression tool.

Feed the wire rope into the opening at the bottom of these eye-end fittings and through the body for a quick and simple installation.

Compress the thin shank wall with a hand tool to attach these light duty eye-end fittings. They are also known as hand swage fittings.

Compress the thin shank wall with a hand tool to attach these light duty clevis-end fittings. They are also known as hand swage fittings.

These clamps have a forged fabrication and are reliable in critical applications. They are not for making slings. These must be oriented with the saddle on the long (live) end and U-bolt on the short (dead) end. They’re also known as wire rope clips.

Constructed with a saddle for both the long (live) end and the short (dead) end, these clamps apply equal pressure without crimping or crushing the wire rope, so orientation doesn't matter. Also known as fist grip wire rope clips.

Make a removable loop without specialty tools for use in noncritical applications, such as fencing. Also known as tiller clamps.

Use in noncritical applications, such as fencing, where the strength of a forged clamp is not required. Install clamps so the saddle is on the long (live) end and the U-bolt is on the short (dead) end. They’re also known as wire rope clips.

Use these sleeves for non-lifting applications such as tethering, securing, and suspending.

Keep multiple sleeves on hand in a variety of sizes.

Also known as standard-pattern thimbles, these provide better protection against fraying than light duty thimbles.

The open-end design leaves more room for connections than other thimbles.

Squeeze the trigger to quickly release the latch.

A wide opening accepts large diameters of rope and pipe. Squeeze the trigger to release.

Lock the bolt with wire or a cable tie for a secure connection.

The narrow end restricts the movement of rope and chain, and the wide end allows room to attach multiple connectors.

Use for three-sided connections. Flat sides ensure webbing and strapping lay flat, so they won't slide and bunch.

Drive the end through the eye and weld or flatten the extended end to resist opening. These links are also known as cold shuts.

The narrow end that restricts the movement of the rope and chain and a wide end that allows room to attach multiple connectors.

Providing better load distribution and alignment than single oblong links, these reduce wear in three and four leg slings.

The narrow end that restricts the movement of the rope and chain and a wide end that allows room to attach multiple connectors.

For security, these connectors must be cut off to be removed.

Also known as hammer locks, assemble by hammering a pin through the center.

Use these to adjust the position of a fitting or an object under load and minimize twisting and knotting.

The snap and split ring swing freely and pull from the center for easy alignment.

Rotating for easy positioning before a load is applied, these minimize twisting and knotting of rope and chain.

These rotate for easy positioning before a load is applied to minimize twisting and knotting of rope and chain.

Adjust the position of a fitting or an object under load and minimize twisting and knotting.

Screw the pin into position by hand for quick installation and removal. They're for use in low-vibration applications where the shackle remains stationary.

The strongest shackles we offer, these connectors have a pin with flush ends that prevents snagging and accidental disengagement.

Screw the pin into position by hand for quick installation and removal. They're for use in low-vibration applications where the shackle remains stationary.

A bolt fastened with a nut and cotter pin makes these shackles more secure than screw-pin shackles.

A lip on the shackle keeps the screw from falling out when loosened.

Indentations in the shackle body hold the head of the pin in place once fastened.

Indentations in the shackle body hold the head of the pin in place once fastened.

A lip on the shackle keeps the pin from falling out when loosened.

Disconnect by pulling the lever or attach rope to the eye on the lever for remote release.

Attach a rope to the ring on the pin for remote release where access in limited. These shackes have a clevis end for making pivoting connections.

Rotating for easy positioning before a load is applied, these have a latch to ensure that rope, chain, and fittings won't separate from the hook when the load slackens.

These have a removable half-link to attach large rings, links, and other closed fittings.

These rotate for easy positioning before a load is applied. They have a latch to ensure rope, chain, and fittings won't separate from the hook when the load slackens.

These have a latch that locks closed when a load is applied for a more secure connection than standard hooks. They rotate for easy positioning before a load is applied.

For a more secure connection than standard hooks, these clevis hooks have a latch that locks closed when a load is applied.

Screw these hooks into place and secure with the included nut.

These rotate for easy positioning before a load is applied.

Insert in eyes, links, rings, and other connectors with small openings. Also known as J-hooks.

Slide the clevis pin into these hooks to attach chain, no extra fittings needed.

Weld these hooks into place.

Easily slip chain, rope, and fittings on and off these open-mouth hooks. Attach your chain to the eye end.

Easily slip chain, rope, and fittings on and off these open-mouth hooks. Attach your chain to the clevis end.

Lock by screwing the latch into the body.

A lock slides upward over the latch to lock. The latch opens outward to accept large diameters of rope.

For extra security, these have a latch that snaps back into place to secure your load.

These hooks meet MS-87006.

One side is closed and the other is open.