Use in noncritical applications, such as fencing, where the strength of a forged clamp is not required. Install clamps so the saddle is on the long (live) end and the U-bolt is on the short (dead) end. They’re also known as wire rope clips.

A clamp and thimble in one convenient fitting simplifies installation while providing support and fray protection to the wire rope loop. Use a torque wrench to tighten the clamp.

These clamps must be oriented with the saddle on the long (live) end and the U-bolt on the short (dead) end. They’re also known as wire rope clips.

These clamps have a forged fabrication and are reliable in critical applications. They are not for making slings. These must be oriented with the saddle on the long (live) end and U-bolt on the short (dead) end. They’re also known as wire rope clips.

Also known as standard-pattern thimbles, these provide better protection against fraying than light duty thimbles.

Also known as heavy-pattern thimbles, these can be used to reinforce the loop of a sling in accordance with ASME B30.9.

Use these sleeves for non-lifting applications such as tethering, securing, and suspending.

These kits include two compression sleeves paired with two thimbles. The thimbles support the wire rope loops and prevent it from fraying.

Install these clevis-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Place the wire rope and sleeve through a hole in the assembly block and tighten into a vise to hold. Then attach the plug driver on the end of a plug to make hammering in the plug easier.

Install these swivel-hook-end plug-lock fittingson the end of wire rope for a strong hold and finished appearance.

Also known as socket-end swage fittings, install these eye-end fittings with a roller swage press for a strong, permanent hold.

Also known as socket-end swage fittings, install these clevis-end fittings with a roller swage press for a strong, permanent hold.

Feed the wire rope into the opening at the bottom of these eye-end fittings and through the body for a quick and simple installation.

Compress the thin shank wall with a hand tool to attach these light duty eye-end fittings. They are also known as hand swage fittings.

Compress the thin shank wall with a hand tool to attach these light duty clevis-end fittings. They are also known as hand swage fittings.

Add a clevis end to wire rope without having to fray the rope or use a compression tool.

Add a mounting-plate to wire rope without having to fray the rope or use a compression tool.

These snaps have an eye that rotates for easy positioning.

A wide opening accepts large diameters of rope and pipe. Squeeze the trigger to release.

Squeeze the trigger to quickly release the latch.

The force of the load helps keep the arms closed. Press the trigger for quick connection and disconnection.

Also known as quick links, screw the nut onto the threaded end to attach end fittings.

Flat sides allow webbing and strapping to lay flat, so they won't slide and bunch.

Attach a rope to the ring on the pin for remote release where access in limited. These shackes have a clevis end for making pivoting connections.

Pull the collar to release the shackle from its locked position.

The spring-loaded latches on these hooks snap back into place, securing your load.

Slide chain and fittings onto the open ends.

These hooks have closed ends on both sides.

The snap and split ring swing freely and pull from the center for easy alignment.

Use these to adjust the position of a fitting or an object under load and minimize twisting and knotting.

Adjust the position of a fitting or an object under load and minimize twisting and knotting.

For easy positioning before a load is applied, these rotate to minimize twisting and knotting of rope and chain.

Minimize twisting and knotting of rope and chain and adjust the position of a fitting or an object under load.

A lock slides upward over the latch to lock. The latch opens outward to accept large diameters of rope.

To open, lift and twist the latch 90°.

A latch ensures rope, chain, and fittings won't separate from the hook when the load slackens.

A latch ensures rope, chain, and fittings won't separate from the hook when the load slackens.

These have a removable half-link to attach large rings, links, and other closed fittings.

A ball-bearing swivel allows these to rotate under load. Attach to chain by inserting the included pin through a link.

These rotate for easy positioning before a load is applied.

For a more secure connection than standard hooks, the latch locks closed when a load is applied.

Screw these hooks into place and secure with the included nut.

Also known as foundry hooks, use these on thick molds, castings, and objects that don't have attachment points.

These kits fit most hooks with a drilled pinhole.

Easily slip chain, rope, and fittings on and off these open-mouth hooks. Attach your chain to the clevis end.

Weld these hooks into place.

Easily slip chain, rope, and fittings on and off these open-mouth hooks. Attach your chain to the eye end.